Search

The increasing amount of data exchange requires higher-capacity optical communication links. Mode division multiplexing (MDM) is considered as a promising technology to support the higher data throughput. In an MDM system, the mode generator and sorter are the backbone. However, most of the current schemes lack the programmability and universality, which makes the MDM link susceptible to the mode crosstalk and environmental disturbances. In this paper, we propose an intelligent multimode optical communication link using universal mode processing (generation and sorting) chips. The mode processor consists of a programmable 4*4 Mach Zehnder interferometer (MZI) network and can be intelligently configured to generate or sort both quasi linearly polarized (LP) modes and orbital angular momentum (OAM) modes in any desired routing state. We experimentally establish a chip-to-chip MDM communication system. The mode basis can be freely switched between four LP modes and four OAM modes. We also demonstrate the multimode optical communication capability at a data rate of 25 Gbit/s. The proposed scheme shows significant advantages in terms of universality, intelligence, programmability and resistance to mode crosstalk, environmental disturbances and fabrication errors, demonstrating that the MZI-based reconfigurable mode processor chip has great potential in long-distance chip-to-chip multimode optical communication systems.

Thermo-optic (TO) phase shifters are very fundamental units in large-scale active silicon photonic integrated circuits (PICs). However, due to the limitation of microheater materials with a trade-off between heating efficiency and absorption loss, designs reported so far typically suffer from slow response time, high power consumption, low yields, and so on. Here, we demonstrate an energy-efficient, fast-response, and low-loss TO phase shifter by introducing hydrogen-doped indium oxide (IHO) films as microheater, and the optimized electron concentration with enhanced mobility endows the IHO high conductivity as well as high near-infrared (NIR) transparency, which allow it to directly contact the silicon waveguide without any insulating layer for efficient tuning and fast response. The TO phase shifter achieves a sub-microsecond response time (970 ns/980 ns) with a {\pi} phase shift power consumption of 9.6 mW. And the insertion loss introduced by the IHO microheater is ~ 0.5 dB. The proposed IHO-based microheaters with compatible processing technology illustrate the great potential of such material in the application of large-scale silicon PICs., Comment: 10 pages, 4 figures, journal

The integration density of photonic integrated circuits has been limited by light coupling between waveguides. Traditional approaches to layout the waveguide with high density are based on refractive index engineering to suppress the light coupling between waveguides. However, these methods mostly require sophisticated and sensitive structure design, thus lack universality. Herein, we propose high-density multi-mode-multi-core integrated photonic waveguides by inserting high-loss metal strips between waveguides. We have achieved a 10-spatial-channel multi-mode-multi-core waveguide with total occupying spacing of 6.6 um. The multi-mode waveguides have a close spacing of 400 nm. The proposed scheme has high fabrication tolerance, ultra-large bandwidth and good compatibility to the complementary metal-oxide-semiconductor technology. It can be applied to any integration platform, any working waveband and any operating mode, providing a universal solution for high-density photonic circuits.

Microlaser with multiple lasing bands is critical in various applications, such as full-colour display, optical communications and computing. Here, we propose a simple and efficient method for homogeneously doping rare earth elements into a silica whispering-gallery-mode microcavity. By this method, we demonstrate simultaneous and stable lasing covering ultraviolet, visible and near-infrared bands in an ultrahigh-Q (exceeding 108) Er-Yb co-doped silica microsphere under room temperature and continuous-wave pump for the first time. The lasing thresholds of the 380, 410, 450, 560, 660, 800, 1080 and 1550 nm-bands are estimated to be 380, 150, 2.5, 12, 0.17, 1.7, 10 and 38 {\mu}W, respectively, where the lasing in the 380, 410 and 450 nm-bands by Er element have not been separately demonstrated under room temperature and continuous-wave pump until this work. This ultrahigh-Q doped microcavity is an excellent platform for high-performance multi-band microlasers, ultrahigh-precise sensors, optical memories and cavity-enhanced light-matter interaction studies., Comment: 28 pages, 5 figures, 49 references

We demonstrate a fully-integrated multipurpose microwave frequency identification system on silicon-on-insulator platform. Thanks to its multipurpose features, the chip is able to identify different types of microwave signals, including single-frequency, multiple-frequency, chirped and frequency-hopping microwave signals, as well as discriminate instantaneous frequency variation among the frequency-modulated signals. This demonstration exhibits fully integrated solution and fully functional microwave frequency identification, which can meet the requirements in reduction of size, weight and power for future advanced microwave photonic processor., 23 pages,6 figures

Integrated optical filter based on microring resonators plays a critical role in many applications, ranging from wavelength division multiplexing and switching to channel routing. Bandwidth tunable filters are capable of meeting the on-demand flexible operations in complex situations, due to their advantages of scalability, multi-function, and energy-saving. It has been investigated recently that parity-time (PT) symmetry coupled-resonant systems can be applied to the bandwidth-tunable filters. However, due to the trade-off between the bandwidth-tunable contrast ratio and insertion loss of system, the bandwidth-tunable contrast ratio of this method is severely limited. Here, the bandwidth-tunable contrast ratio is defined as the maximum bandwidth divided by the minimum bandwidth. In this work, we show that high bandwidth-tunable contrast ratio and low insertion loss of system can be achieved simultaneously by increasing the coupling strength between the input port and the resonant. System characterizations under different coupling states reveal that the low insertion loss can be obtained when the system initially operates at the over-coupling condition. A high bandwidth-tunable contrast ratio PT-symmetry band-pass filter with moderate insertion loss is shown on the Silicon platform. Our scheme provides an effective method to reduce the insertion loss of on-chip tunable filters, which is also applicable to the high-order cascaded microring systems., Comment: 13 pages, 5 figures

Encircling an exceptional point (EP) in a parity-time (PT) symmetric system has shown great potential for chiral optical devices, such as chiral mode switching for symmetric and anti-symmetric modes. However, the chiral switching for polarization states has never been reported although chiral polarization manipulation has significant applications in imaging, sensing, and communication etc. Here inspired by the anti-PT symmetry, we demonstrate an on-chip chiral polarizer by constructing polarization-coupled anti-PT symmetric system for the first time. The transmission axes of the chiral polarizer are different for forward and backward propagation. A polarization extinction ratio of over 10 dB is achieved for both propagating directions. Moreover, a telecommunication experiment is performed to demonstrate the potential applications in polarization encoding signals. It provides a novel functionality for encircling-an-EP parametric evolution and offer a new approach for on-chip chiral polarization manipulation.

We raise a detuning-dependent loss mechanism to describe the soliton formation dynamics when the lumped filtering operation is manipulated in anomalous group velocity dispersion regime, using stability analysis of generalized Lugiato-Lefever equation., Comment: 3 pages, 2 figures

Thermo-optic microheater is indispensable in silicon photonic devices for smart and reconfigurable photonic networks. Much efforts have been made to improve the metallic microheater performance in the past decades. However, because of the metallic nature of light absorption, placing the metallic microheater very close to the waveguide for fast response is impractical and has not been done experimentally. Here, we experimentally demonstrate a metallic microheater placed very close to the waveguide based on parity-time (PT) symmetry breaking. The intrinsic high loss of metallic heater ensures the system will operate in the PT-symmetry-broken region, which guarantee the low loss of light in the silicon waveguide. Moreover, heating at a close range significantly reduces the response time. A fast response time of ~1 us is achieved without introducing extra loss. The insertion loss is only 0.1 dB for the long heater. The modulation bandwidth is 280 kHz, which is an order of magnitude improvement when compared with that of the mainstream thermo-optic phase shifters. To verify the capability of large-scale integration, a 1*8 phased array for beam steering is also demonstrated experimentally with the PT-symmetry-broken metallic heaters. Our work provides a novel design concept for low-loss fast-response optical switches with dissipative materials and offers a new approach to enhance the performance of thermo-optic phase shifters.

On-chip manipulation of single resonance over broad background comb spectra of microring resonators is indispensable, ranging from tailoring laser emission, optical signal processing to non-classical light generation, yet challenging without scarifying the quality factor or inducing additional dispersive effects. Here, we propose an experimentally feasible platform to realize on-chip selective depletion of single resonance in microring with decoupled dispersion and dissipation, which are usually entangled by Kramer-Kroning relation. Thanks to the existence of non-Hermitian singularity, unsplit but significantly increased dissipation of the selected resonance is achieved due to the simultaneous collapse of eigenvalues and eigenvectors, fitting elegantly the requirement of pure single-mode depletion. With delicate yet experimentally feasible parameters, we show explicit evidence of modulation instability as well as deterministic single soliton generation in microresonators induced by depletion in normal and anomalous dispersion regime, respectively. Our findings connect non-Hermitian singularities to wide range of applications associated with selective single mode manipulation in microwave photonics, quantum optics, ultrafast optics and beyond., Comment: 5 pages, 4 figures

White laser covering the visible color spectrum is critical in various applications including vivid display, holographic imaging and light-based version of Wi-Fi, but it is still challenging to realize the white microlaser due to the rigorous requirement in the balance between the optical gain and the feedback at different wavelengths. Here, we employ Tm, Er and Yb ions corporately for the upconversion white lasing in a single ultrahigh quality (Q) (up to 108) doped microcavity, where the thresholds of the red, green and blue lasers are about 90, 500 and 300 {\mu}W, respectively. To the best of our knowledge, it is the first rare-earth elements based room-temperature, continuous-wave white microlaser, which exhibits relatively stable chromaticity over 180 minutes, making it possible for practical applications.

On-chip optical interconnect has been widely accepted as a promising technology to realize future large-scale multiprocessors. Mode-division multiplexing (MDM) provides a new degree of freedom for optical interconnects to dramatically increase the link capacity. Present on-chip multimode devices are based on traditional wave-optics. Although large amount of computation and optimization are adopted to support more modes, mode-independent manipulation is still hard to be achieved due to severe mode dispersion. Here, we propose a universal solution to standardize the design of fundamental multimode building blocks, by introducing a geometrical-optics-like concept adopting waveguide width larger than the working wavelength. The proposed solution can tackle a group of modes at the same time with very simple processes, avoiding demultiplexing procedure and ensuring compact footprint. Compare to conventional schemes, it is scalable to larger mode channels without increasing the complexity and whole footprint. As a proof of concept, we demonstrate a set of multimode building blocks including crossing, bend, coupler and switches. Low losses of multimode waveguide crossing and bend are achieved, as well as ultra-low power consumption of the multimode switch is realized since it enables reconfigurable routing for a group of modes simultaneously. Our work promotes the multimode photonics research and makes the MDM technique more practical.

Filters are key devices in optical systems and are usually applied to signal suppression or selection based on their amplitude frequency responses. Different from amplitude filtering, an all-pass filter (APF) is a unique type of filter that exhibits a uniform amplitude and variable phase in the frequency response. Traditionally, an APF is designed to be ideal and lossless, which is impossible in practice. Here we demonstrate a method of realizing an APF even when transmission loss exists, and a possible structure for realizing the lossy APF is proposed. The method indicates that a lossy APF can be realized by introducing self-compensation of loss to the structure of an ideal single-stage APF, and an APF based on silicon-on-insulator (SOI) foundry is fabricated and demonstrated. The method of self-compensation of loss can also be used to realize APFs in the electrical domain. We anticipate that our work will inspire realizations of more APF-related devices that once seemed impossible in practice.

Photonic signal processing is essential in the optical communication and optical computing. Numerous photonic signal processors have been proposed, but most of them exhibit limited reconfigurability and automaticity. A feature of fully automatic implementation and intelligent response is highly desirable for the multipurpose photonic signal processors. Here, we report and experimentally demonstrate a fully self-learning and reconfigurable photonic signal processor based on an optical neural network chip. The proposed photonic signal processor is capable of performing various functions including multichannel optical switching, optical multiple-input-multiple-output descrambler and tunable optical filter. All the functions are achieved by complete self-learning. Our demonstration suggests great potential for chip-scale fully programmable optical signal processing with artificial intelligence.

Photonic time-stretch overcomes the speed limitation of conventional digitizers, and enables the observation of non-repetitive and statistically rare phenomena that occur on short timescales. In most of the time-stretch applications, large temporal dispersion is highly desired to satisfy the far-field diffraction regime. However, most conventional spatial disperser or chirped fiber Bragg grating are constrained by its spatial volume, which can be overcome by the ultra-low-loss dispersive fiber, as an ideal medium for large temporal dispersion , while it suffers from the third-order dispersion and aberrations. In this paper, an optical phase conjugation based third-order dispersion compensation scheme is introduced, with accumulated dispersion and eliminated third dispersion, and achieved negative and positive 3400-ps2 pure temporal dispersion of over 30-nm bandwidth. Leveraging this pure temporal dispersion, up to 2% temporal aberrations have been eliminated; furthermore, a Fourier domain spectroscopy has achieved a record 15000 optical effective resolvable points, with non-degraded 2-pm resolution over 30-nm range

We demonstrate a multipurpose microwave frequency identification solution that is implemented based on a photonic integrated chip and is able to identify different types of microwave signals, including single-frequency, multiple-frequency, chirped and frequency-hopping microwave signals. The key component is a thermally-tunable high-Q-factor silicon microring resonator which is used to implement the frequency-to-time mapping. The frequency measurement range is ultra-wide, from 1 to 30 GHz, with a high resolution of 375 MHz and a low measurement error of 237.3 MHz. This demonstration opens the door for future fully integrated solution for high speed, wideband and multipurpose signal identification with high resolution., First and second author contributed equally to this work

Controlling the directionality of surface plasmon polaritons (SPPs) has been widely studied, while the direction of SPPs was always switched by orthogonal polarizations in the reported methods. Here, we present a scheme to control the directionality of SPPs by arbitrary spin polarizations. Extremely, the device can split two quite adjacent polarization components to two opposite directions. The versatility of the presented design scheme can offer opportunities for polarization sensing, polarization splitting and polarization-controlled plasmonic devices., Comment: First and second author contributed equally to this work

Surface plasmon polaritons have attracted varies of interests due to its special properties, especially in the polarization-controlled devices. Typically, the polarization-controlled devices include directional coupling, focusing lens and plasmonic vortex lens, and almost all of them are controlled by the input circularly polarized light or the linearly polarized light. We present a novel device that realize the functions of directional coupling and focusing with high polarization extinction ratio for arbitrary spin of input light. This device offers opportunities for polarization sensing, polarization splitting and polarization-multiplexed near-field images and surface plasmon holography in the future., Comment: First and second authors contributed equally to this work

The ability to manipulate the frequency of light is of great importance in both fundamental quantum sciences and practical applications. Traditional method for frequency conversion relies on nonlinear optical processes, which are faced with the obstacles of low efficiency and limited bandwidth. Recent developments of topological photonics introduce the concepts of gauge potentials and magnetic fields to the realm of photons. Here, we demonstrate versatile frequency manipulation of light via photonic gauge potentials in a fiber-optic communication system. The gauge potential of frequency dimension is realized by controlling the initial phase of electro-optic phase modulation. A maximum 50 GHz frequency shift and three-fold bandwidth expansion for frequency combs are achieved by choosing different gauge potentials. By adopting two cascaded phase modulators with different gauge potentials, we also realize "negative refraction" for frequency combs and frequency "perfect imaging"for arbitrarily input spectra. These results may pave the way towards versatile frequency management in quantum optics and classical optical communications., 14 pages,5 figures

Manipulation of orbital angular momentum (OAM) of light is essential in OAM-based optical systems. Especially, OAM divider, which can convert the incoming OAM mode into one or several new smaller modes in proportion at different spatial paths, is very useful in OAM-based optical networks. However, this useful tool was never reported yet. For the first time, we put forward a passive OAM divider based on coordinate transformation. The device consists of a Cartesian to log-polar coordinate converter and an inverse converter. The first converter converts the OAM light into a rectangular-shaped plane light with a transverse phase gradient. And the second converter converts the plane light into multiple diffracted light. The OAM of zeroth-order diffracted light is the product of the input OAM and the scaling parameter. The residual light is output from other diffracted orders. Furthermore, we extend the scheme to realize equal N-dividing of OAM and arbitrary dividing of OAM. The ability of dividing OAM shows huge potential for OAM-based classical and quantum information processing., 7

The function to measure orbital angular momentum (OAM) distribution of vortex light is essential for OAM applications. Although there are lots of works to measure OAM modes, it is difficult to measure the power distribution of different OAM modes quantitatively and instantaneously, let alone measure the phase distribution among them. In this work, we demonstrate an OAM complex spectrum analyzer, which enables to measure the power and phase distribution of OAM modes simultaneously by employing rotational Doppler Effect. The original OAM mode distribution is mapped to electrical spectrum of beating signals with a photodetector. The power distribution and phase distribution of superimposed OAM beams are successfully retrieved by analyzing the electrical spectrum. We also extend the measurement to other spatial modes, such as linear polarization modes. These results represent a new landmark of spatial mode analysis and show great potentials in optical communication and OAM quantum state tomography., Comment: 17 pages, 8 figures

We theoretically investigate the optical rotational Doppler Effect using modal expansion method. We find that the frequency shift content is only determined by the surface of spinning object and the reduced Doppler shift is linear to the change of mode index. The theoretical model makes us better understand the physical processes of rotational Doppler Effect. It can provide theoretical guidance for many related applications, such as detection of rotating bodies, detection of OAM and frequency shift., Comment: 8 pages, 4 figures