Search

BaAl 2 Si 2 O 8 /BN (BAS/BN) ceramic composites were prepared using hot press sintering. The amorphous state of BAS ceramics exhibits a low melting point, high liquid-phase mobility, and good infiltration with BN grains, facilitating the sintering process. Conversely, the crystalline state of BAS has a high melting point and strength, contributing to the strengthening and toughening of the composite. The mechanical properties, thermal properties and thermal shock resistance of BAS/BN ceramic composite was investigated. Ceramic composites containing 40 vol% BAS have the best overall mechanical properties with bending strength, elastic modulus, fracture toughness, and hardness of 175 ± 3 MPa, 114.0 ± 1.2 GPa, 2.02 ± 0.10 MPa · m1/2, and 1.08 ± 0.01 GPa, respectively. The BAS/BN ceramic composite has excellent thermal shock resistance, and the residual bending strength shows a pattern of increasing and then decreasing with increasing thermal shock temperature difference. Finite element calculation results show that the cooling process is basically completed after 20 s of water quenching, the maximum thermal stress generated is about 22 MPa. [Display omitted] • The mechanical properties and thermal shock resistance of h -BN ceramics are enhanced by the introduction of BAS. • The main phases of BAS/BN ceramic composites are h -BN and h -BaAl 2 Si 2 O 8. • The thermal shock damage mechanism of BAS/BN ceramic composites is elucidated. [ABSTRACT FROM AUTHOR]

Achieving an optimal balance between mechanical properties, dielectric properties, and thermal shock resistance presents a significant challenge in the development of advanced ceramics. This study investigates Si 3 N 4 -BN composite materials, prepared by hot-press sintering with magnesium aluminum silicate (MAS) as the sintering additive, to assess the impact of varying hexagonal boron nitride (h -BN) content on their mechanical and dielectric properties, as well as their thermal shock resistance. At an h -BN content of 20 wt%, the BN layers act as a toughening phase through a pull-out mechanism, minimally impacting the composite's density. This composition results in superior fracture toughness (7.4 MPa m1/2), high strength (598 MPa), low dielectric constants (∼6.8), and dielectric loss (∼7.4 × 10−3). Notably, after a thermal shock at 1000 °C, the composite exhibits a peak residual strength of 621 MPa, surpassing its initial strength. This enhanced performance is attributed to the formation of a dense Mg–Al–Si–B–O oxide glass layer on the surface during thermal shock, which not only repairs surface defects but also induces compressive stress. The development of the Si 3 N 4 -BN-MAS composite, with its outstanding comprehensive performance, marks a significant advancement for materials used in high-temperature wave transmission applications. [ABSTRACT FROM AUTHOR]

MXenes have good application prospects due to the attractive mechanical and physicochemical properties. Here, for the first time, silicoboron carbonitride (Si–B–C–N) ceramics with the integration of MXene(Ti 3 C 2 T x) nanosheets were developed, and the influences of MXene additives (1.0–3.0 wt%) on mechanical properties and microstructures were investigated. The ceramics containing 3.0 wt% MXene(Ti 3 C 2 T x) show better mechanical properties including fracture toughness of 7.6 MPa‧m1/2, 36% higher than ceramics without any additives. The toughening mechanisms consist of pull-out, delamination, crack bridging, and crack deflection. This work demonstrates that MXenes are good reinforcements for enhancing the fracture toughness of structural ceramics, and also paves the way for the investigation of high-temperature properties of MXene-containing ceramics. [ABSTRACT FROM AUTHOR]

The processing of 3D carbon fiber reinforced SiCN ceramic matrix composites prepared by polymer impregnation and pyrolysis (PIP) route was improved, and factors that determined the mechanical performance of the resulting composites were discussed. 3D C f /SiCN composites with a relative density of ∼81% and uniform microstructure were obtained after 6 PIP cycles. The optimum bending strength, Young's modulus and fracture toughness of the composites were 75.2 MPa, 66.3 GPa and 1.65 MPa m1/2, respectively. The residual strength retention rate of the as-pyrolyzed composites was 93.3% after thermal shock test at Δ T = 780 °C. It further degraded to 14.6% when the thermal shock temperature difference reached to 1180 °C. The bending strength of the composites was 35.6 MPa after annealing at 1000 °C in static air. The deterioration of the bending strength should be attributed to the strength degradation of carbon fibers and decomposition of interfacial structure. [ABSTRACT FROM AUTHOR]

Si-B-C-N ceramic monoliths with LaB 6 additive were prepared by mechanical alloying followed by spark plasma sintering. The microstructures and mechanical properties were investigated compared to LaB 6 -free Si-B-C-N counterparts. After sintered at 1900 °C/50 MPa, the La/Si-B-C-N monoliths provide well-developed BN(C) flakes (≤100 nm in thickness) and improved fracture toughness, while the BN(C) ones show no lamellar microstructures in Si-B-C-N systems. The solid-solution of La in BN(C) grains promotes ordered arrangement of BN(C) along the (0002) plane causing in situ growth of BN(C) thus leading to an increase in toughness by 40% (from 5.6 to 7.8 MPa m −1/2 ). [ABSTRACT FROM AUTHOR]