Search

This paper studies particle motion and flow field characteristics with fly ash as an example and combine the experiments to analyze the separation process of rotary triboelectric separator in detail. Under boundary reference conditions of 22 kV plate voltage, 3 m/s feed flow, and 1815 r/min (189.95 rad/s) friction wheel speed, it simulated single-particle and particle group movement with different plate voltages and different feeding positions. Simulation of particle movement shows that particles may collide with a plate to cause serious particle mixing when plate voltage is higher. The initial velocity direction of particles is vertical downward and particles enter the separation chamber from the middle of the feeding port as much as possible to achieve better separation. The analysis of the flow field shows that the increase of the feeding airflow speed leads to a higher flow velocity inside the friction chamber and increases turbulence intensity; increases in friction wheel speed enhances flow field uniformity in the friction chamber and it is accompanied by an increase in velocity gradient; The co-flow speed mainly affects airflow field in the sorting room, the increase of co-flow speed within a certain range effectively stabilizes airflow field in the sorting room. [ABSTRACT FROM AUTHOR]

The strength properties of fault rocks at shearing rates spanning the transition from crystal–plastic flow to frictional slip play a central role in determining the distribution of crustal stress, strain, and seismicity in tectonically active regions. We review experimental and microphysical modelling work, which is aimed at elucidating the processes that control the transition from pervasive ductile flow of fault rock to rate-and-state-dependent frictional (RSF) slip and to runaway rupture, carried out at Utrecht University in the past 2 decades or so. We address shear experiments on simulated gouges composed of calcite, halite–phyllosilicate mixtures, and phyllosilicate–quartz mixtures performed under laboratory conditions spanning the brittle–ductile transition. With increasing shear rate (or decreasing temperature), the results consistently show transitions from (1) stable velocity-strengthening (v -strengthening) behaviour, to potentially unstable v -weakening behaviour, and (2) back to v strengthening. Sample microstructures show that the first transition seen at low shear rates and/or high temperatures represents a switch from pervasive, fully ductile deformation to frictional sliding involving dilatant granular flow in localized shear bands where intergranular slip is incompletely accommodated by creep of individual mineral grains. A recent microphysical model, which treats fault rock deformation as controlled by competition between rate-sensitive (diffusional or crystal–plastic) deformation of individual grains and rate-insensitive sliding interactions between grains (granular flow), predicts both transitions well. Unlike classical RSF approaches, this model quantitatively reproduces a wide range of (transient) frictional behaviours using input parameters with direct physical meaning, with the latest progress focusing on incorporation of dynamic weakening processes characterizing co-seismic fault rupture. When implemented in numerical codes for crustal fault slip, the model offers a single unified framework for understanding slip patch nucleation and growth to critical (seismogenic) dimensions, as well as for simulating the entire seismic cycle. [ABSTRACT FROM AUTHOR]

The strength properties of fault rocks at shearing rates spanning the transition from crystal-plastic flow to frictional slip play a central role in determining the distribution of crustal stress, strain and seismicity in tectonically-active regions. We review experimental and microphysical modelling work aimed at elucidating the processes that control the transition from pervasive ductile flow of fault rock to rate-and-state dependent frictional (RSF) slip and to runaway rupture, carried out at Utrecht University in the past two or so decades. We address shear experiments on simulated gouges composed of calcite, halite-phyllosilicate mixtures, and phyllosilicate-quartz mixtures, performed under laboratory conditions spanning the brittle-ductile transition. With increasing shear rate (or decreasing temperature), the results consistently show transitions from (1) stable, velocity(v)-strengthening to potentially unstable, v-weakening behavior, and (2) back to v-strengthening. Sample microstructures show that the first transition, seen at low shear rates and/or high temperatures, represents a switch from pervasive, fully ductile deformation to frictional sliding, involving dilatant granular flow in localized shear bands, where intergranular slip is incompletely accommodated by creep of individual mineral grains. A recent microphysical model, treating fault rock deformation as controlled by a competition between rate-sensitive (diffusional or crystal-plastic) deformation of individual grains and rate-insensitive sliding interactions between grains (granular flow), predicts both transitions well. Unlike classical RSF approaches, this model quantitatively reproduces a wide range of (transient) frictional behaviors using input parameters with direct physical meaning. When implemented in numerical codes for crustal fault-slip, it offers a single, unified framework for understanding slip patch nucleation and growth to critical (seismogenic) dimensions, and for simulating the entire seismic cycle. [ABSTRACT FROM AUTHOR]

Understanding what controls the travelling distance of large landslides has been the topic of considerable debate. By combining observation and experimental data with depth-averaged continuum modelling of landslides and generated seismic waves, it was empirically observed that lower effective friction had to be taken into account in the models to reproduce the dynamics and runout distance of larger volume landslides. Moreover, such simulation and observation results are compatible with a friction weakening with velocity as observed in earthquake mechanics. We investigate here as to whether similar empirical reduced friction should be put into discrete element models (DEM) to reproduce observed runout of large landslides on Earth and on Mars. First we show that, in the investigated parameter range and for a given volume, the runout distance simulated by 3D DEM is not much affected by the number (i.e. size) of grains once this number attains ~ 8000. We then calibrate the model on laboratory experiments and simulate other experiments of granular flows on inclined planes, making it possible for the first time to reproduce the observed effect of initial volume and aspect ratio on runout distances. In particular, the normalised runout distance starts to depend on the volume involved only above a critical slope angle > 16–19°, as observed experimentally. Finally, based on field data (volume, topography, deposit), we simulate a series of landslides on simplified inclined topography. The empirical friction coefficient, calibrated to reproduce the observed runout for each landslide, is shown to decrease with increasing landslide volume (or velocity), going down to values as low as 0.1–0.2. No distinguishable difference is observed between the behaviour of terrestrial and Martian landslides. [ABSTRACT FROM AUTHOR]