Search

Efficiencies of organic solar cells have practically doubled since the development of non‐fullerene acceptors (NFAs). However, generic chemical design rules for donor‐NFA combinations are still needed. Such rules are proposed by analyzing inhomogeneous electrostatic fields at the donor–acceptor interface. It is shown that an acceptor–donor–acceptor molecular architecture, and molecular alignment parallel to the interface, results in energy level bending that destabilizes the charge transfer state, thus promoting its dissociation into free charges. By analyzing a series of PCE10:NFA solar cells, with NFAs including Y6, IEICO, and ITIC, as well as their halogenated derivatives, it is suggested that the molecular quadrupole moment of ≈75 Debye Å balances the losses in the open circuit voltage and gains in charge generation efficiency. [ABSTRACT FROM AUTHOR]

Abstract: Organic bulk heterojunction solar cells based on small molecule acceptors have recently seen a rapid rise in the power conversion efficiency with values exceeding 13%. This impressive achievement has been obtained by simultaneous reduction of voltage and charge recombination losses within this class of materials as compared to fullerene‐based solar cells. In this contribution, the authors review the current understanding of the relevant photophysical processes in highly efficient nonfullerene acceptor (NFA) small molecules. Charge generation, recombination, and charge transport is discussed in comparison to fullerene‐based composites. Finally, the authors review the superior light and thermal stability of nonfullerene small molecule acceptor based solar cells, and highlight the importance of NFA‐based composites that enable devices without early performance loss, thus resembling so‐called burn‐in free devices. [ABSTRACT FROM AUTHOR]

Abstract: Nonfullerene acceptors (NFAs) in blends with highly crystalline donor polymers have been shown to yield particularly high device voltage outputs, but typically more modest quantum yields for photocurrent generation as well as often lower fill factors (FF). In this study, we employ transient optical and optoelectronic analysis to elucidate the factors determining device photocurrent and FF in blends of the highly crystalline donor polymer PffBT4T‐2OD with the promising NFA FBR or the more widely studied fullerene acceptor PC71BM. Geminate recombination losses, as measured by ultrafast transient absorption spectroscopy, are observed to be significantly higher for PffBT4T‐2OD:FBR blends. This is assigned to the smaller LUMO‐LUMO offset of the PffBT4T‐2OD:FBR blends relative to PffBT4T‐2OD:PC71BM, resulting in the lower photocurrent generation efficiency obtained with FBR. Employing time delayed charge extraction measurements, these geminate recombination losses are observed to be field dependent, resulting in the lower FF observed with PffBT4T‐2OD:FBR devices. These data therefore provide a detailed understanding of the impact of acceptor design, and particularly acceptor energetics, on organic solar cell performance. Our study concludes with a discussion of the implications of these results for the design of NFAs in organic solar cells. [ABSTRACT FROM AUTHOR]

Organic solar cells that are free of burn-in, the commonly observed rapid performance loss under light, are presented. The solar cells are based on poly(3-hexylthiophene) (P3HT) with varying molecular weights and a nonfullerene acceptor (rhodanine-benzothiadiazole-coupled indacenodithiophene, IDTBR) and are fabricated in air. P3HT:IDTBR solar cells light-soaked over the course of 2000 h lose about 5% of power conversion efficiency (PCE), in stark contrast to [6,6]-Phenyl C61 butyric acid methyl ester (PCBM)-based solar cells whose PCE shows a burn-in that extends over several hundreds of hours and levels off at a loss of ≈34%. Replacing PCBM with IDTBR prevents short-circuit current losses due to fullerene dimerization and inhibits disorder-induced open-circuit voltage losses, indicating a very robust device operation that is insensitive to defect states. Small losses in fill factor over time are proposed to originate from polymer or interface defects. Finally, the combination of enhanced efficiency and stability in P3HT:IDTBR increases the lifetime energy yield by more than a factor of 10 when compared with the same type of devices using a fullerene-based acceptor instead. [ABSTRACT FROM AUTHOR]

The photovoltaic performance of blends of a series of 4,4′-Difluoro-4-bora-3a,4a-diaza-s-indacenes)-based (BODIPY) conjugated polymers donors with fullerene electron acceptors is investigated. Despite the high Voc values observed, solar cell device yields relatively low power conversion efficiencies. Our study takes into account the materials’ structure-property relationship, light harvesting capabilities, charge transport, collection properties and morphological characteristics to elucidate factors affecting the photovoltaic performance in this class of polymers. We show that elimination of low molecular weight species and suitable electrodes for hole collection can be used to overcome some of the observed limitations on photovoltaic performance. [ABSTRACT FROM AUTHOR]

Abstract: 4,7-Bis(2,3-dihydrothieno [3,4-b] [1,4] dioxin-5-yl)-2-dodecyl-2H-benzo [1,2,3] triazole (BEBT) was polymerized both electrochemically (ePBEBT) and chemically (cPBEBT). Since chemical polymerization enabled a soluble polymer in common organic solvents, a single layer electrochromic device of ePBEBT was constructed. The polymer cPBEBT was also used in bulk heterojunction (BHJ) solar cells as the active layer in combination with a soluble fullerene derivative, 1-(3-methoxycarbonyl)-propyl-1-1-phenyl-(6,6)C61 PCBM. [Copyright &y& Elsevier]