Search

Gas reservoirs have significant engineering characteristics of injection and extraction. The reservoir cap rock is subjected to cyclic alternating loading and has the potential risk of seal failure. Therefore, it is necessary to study the stress−percolation−damage mechanism of the reservoir cap rock in depleted gas reservoirs. The rock Mechanics Test System (MTS) was used to study the permeability characteristics of a typical mud shale cap layer under different loading and unloading rates, analyze the deformation characteristics and permeability performance evolution law of the rock under the confining pressure alternation, and study the effects of loading and unloading rate, confining pressure and number of cycles on the permeability of the cap rock. The test results show that with the increase in the number of cycles, the hysteresis loop moves in the direction of axial strain increase offset. The overall morphology is presented as an elongated type, and the damage of the specimen is small in the cyclic confining pressure; At the beginning of the cycling period, the permeability decreases with the increase in the confining pressure in the form of a negative exponential. At the later stage of the cycling period, the permeability basically stays unchanged, and is maintained at a low level; At low confining pressure, permeability also decreases in a negative exponential form with the increase in the number of confining pressure cycles; The greater the loading and unloading rate at the beginning of the cycle, the more the permeability decreases; There is a tendency of sealing improvement under cyclic loading in the gas storage of depleted reservoirs with mud shale as the cap layer. The results of the study can provide technical parameters for the evaluation of the cap sealing of gas storage of depleted reservoirs. [ABSTRACT FROM AUTHOR]

The good sealing caprocks are significant for the integrity of underground gas storage (UGS) in depleted natural gas reservoirs. The screening of parameters, weight assignment, and evaluation method are important for evaluating the sealing performance of caprocks. Many factors can affect the sealing performance of caprocks, including caprock thickness, lithology, brittleness, porosity and permeability, breakthrough pressure, etc. In this paper, the dominant factors in the sealing performance of caprocks in UGSs are systematically analyzed, and the weights of these factors are analyzed by the analytic hierarchy process (AHP). The fuzzy comprehensive evaluation method (FCEM) is applied in the sealing evaluation of caprocks in three typical underground gas reservoirs (i.e., Zhujiadun, Xu-2, and Xing-9) in China. The sandstone reservoir in the Zhujiadun gas field is only about 20 m, and the thickness of the overlying mudstone is about 600 m. The caprock of the Xu-2 gas reservoir in Zhongba gas field is well distributed and developed, and the breakthrough pressure is relatively large. The caprock of Xing-9 gas field is mudstone with a thickness of over 400 m. The results show that the breakthrough pressure and permeability are the key parameters affecting the sealing ability of caprocks, with weights of 0.4291 and 0.2157, respectively. Among these three examples of gas fields, the sealing performance of caprocks in Zhujiadun gas storage is the best. The evaluation procedure and methods proposed in this paper are valuable for the evaluation of the tightness of caprocks in depleted gas reservoirs. [ABSTRACT FROM AUTHOR]

The structure of caprocks is often greatly altered by different scales of faults or fissures in long-term geological tectonic evolution, and the sealing performance may be deteriorated. In this paper, a simplified geological model characterized as multilayered sandstone and fault-bearing caprocks extracted from the Shuang 6 underground gas storage located in the Liaohe oilfield was established. Different fault geometry (e.g., fault length, fault dip angle, and fault type) and seepage attributes (porosity and permeability) were considered to illustrate their impacts on natural gas migration during the cyclic high rate of injection and production of natural gas. The results showed that the seepage anisotropy and the natural gas front are strongly affected by the formation properties and, especially, are hindered by the low permeability sandstone layers. The difference in the lateral migration distance of natural gas in different layers can reach 110 m at the end of the injection period, with an annual injection volume of 108 m3. The migration of natural gas along the fault zone is mainly controlled by the permeability of faults, followed by fault scale, fault dip angle, and fault type. The sealing failure of caprocks in the fault zone does not occur based on the simulated gas migration distribution, showing that a very limited amount of natural gas migrates into the caprocks. [ABSTRACT FROM AUTHOR]

In the current international situation, energy storage is an important means for countries to stabilize their energy supply, of which underground storage of natural gas is an important part. Depleted gas reservoir type underground gas storage (UGS) has become the key type of gas storage to be built by virtue of safety and environmental protection and low cost. The multi-cycle high injection and production rate of natural gas in the depleted gas reservoir type UGS will cause the in-situ stress disturbance. The slip risk of fault in the geological system increases greatly compared with that before the construction of the storage engineering, which becomes a great threat to the sealing of the gas storage. Reasonable injection and production strategy depend on the reliable assessment of the shear behavior of the fault belt, which can guarantee the sealing characteristics of the UGS geological system and the efficient operation of the UGS. Therefore, the shear behavior of the fault is studied by carrying out experiments, which can provide important parameters for the evaluation of fault stability. However, there is a large gap between the rock samples used in the previous experimental study and the natural faults, and it is difficult to reflect the shear failure characteristics of natural faults. In this paper, similar fault models based on high-precision three-dimensional scanners and engraving machines, filled with three types of fault gouge, are prepared for a batch of representative direct shear tests. The results show that the peak shear strength of the fault rocks with a shear surface is higher than that of the fault rocks with a tensile surface. Compared with the clay mineral content, the roughness of the fault surface is much more significant for the shear strength of the fault rock. For the fault rocks with similar fault surface morphology, the higher the clay content in the fault gouge, the greater the shear strength of the fault rocks. For the fault rocks with different fault surface morphology and the same fault gouge, the cohesion and internal friction angle of the tensile type is generally smaller than that of the shear type. [ABSTRACT FROM AUTHOR]

The underground gas storage (UGS) in depleted sandstone reservoirs forms the largest proportion of the UGS market in China. Multiple cycles of natural gas injection and production in the sandstone cause the rapid increase and drawdown of pore pressure, which may induce damage to the rock skeleton structure, and cause complex fluid flow paths in the sandstone reservoir. In this paper, transverse relaxation time (T2), nuclear magnetism resonance imaging, and high-pressure mercury intrusion analysis are combined to evaluate the variation in pore structure of medium-grained sandstone. The results show that cyclic injection and production of fluid leads to a slight increase in total pore volume, indicating that weak damage to rocks occurs. The T2 spectrum at the low pore pressure (10 MPa) and high pore pressure (25 MPa) both show that the shrinkage of the medium-size pores occurs after multiple cycles of injection and production. The pore volume of large-size pores was not highly correlated with the number of cycles. With the increase in pore pressure, the pore volume ratio under high pore pressure increased with the number of cycles, while it fluctuated strongly under low pore pressure. [ABSTRACT FROM AUTHOR]

The mechanical properties and permeability of gypsum caprock have a significant influence on the tightness and stability of salt cavern gas storage, a series of tests were carried out to investigate the mechanical properties, permeability and AE characteristics of gypsum under THM coupling in this work. The peak strength of gypsum increases with the increase of confining pressure and the decrease of temperature, the failure and dilatation failure criteria are obtained by utilizing Mogi failure criterion. The permeability decreases with the increase of temperature in the compaction and linear elastic deformation stage, and the final permeability decreases with the increase of temperature under the confining pressure of 5 MPa and 15 MPa, while increase with the increase of temperature under the confining pressure of 25 MPa and 35 MPa. And the permeability decreases with the increase of confining pressure in the whole test process because of the constrain of confining pressure on the formation of microcracks and pores. The best fitting formulas of the relationship between permeability and confining pressure is given by fitting at 25 °C and 110 °C, which can be expressed by two exponential functions. The AE characteristics also confirmed that the increase of confining pressure and temperature inhibited the formation of microcracks and pores, and the AE peaks have the same hysteresis effect as the stress peaks. It is noted that the peaks of AE ring count increase with the increase of temperature under the confining pressure of 35 MPa. [ABSTRACT FROM AUTHOR]

Salt cavern gas storage (SCGS) is a mature energy storage method that is applied around the world. Insoluble sediment particle (ISP) accumulated at the bottom of the salt cavern seriously affect the storage capacity of salt caverns. The ISP has greatly restricted large-scale underground energy in salt caverns in China. However, if the void in the ISP can be used for gas storage (SVGS), the gas storage capacity of salt caverns will be greatly improved. The sediment void is related to the grain size distribution, accumulation morphology, mechanical properties, and falling movement. Therefore, four models (grading model, accumulating model, mechanics and motion model, and simulation model) of the SVGS are constructed by the four theories (grading theory, accumulation theory, contact force chain and motion theories, and experiment and numerical theories) to analyze the feasibility of SVGS. Then, the practical application, model validation, and prospects of SVGS are also discussed. The models and practical application show that the SVGS is feasible, and it has wide application prospects. The research provides a favorable reference for the implementation of SVGS in China. • A method of the salt cavern sediment void gas storage is proposed. • The grain model and accumulation model of sediment void gas storage are analyzed. • The mechanics, motion model, and simulation model of sediment void gas storage are analyzed. • The practical applications of sediment void gas storage are analyzed. • The evaluation methods, site problems, key points, prospects of sediment void gas storage are analyzed. [ABSTRACT FROM AUTHOR]