Search

When a drop of a polar liquid slides over a hydrophobic surface, it acquires a charge. As a result, the surface charges oppositely. For applications such as the generation of electric energy, lubricant-infused surfaces (LIS) may be important because they show a low friction for drops. However, slide electrification on LIS has not been studied yet. Here, slide electrification on lubricant-infused surfaces was studied by measuring the charge generated by series of water drops sliding down inclined surfaces. As LIS, we used PDMS-coated glass with micrometer-thick silicone oil films on top. For PDMS-coated glass without lubricant, the charge for the first drop is highest. Then it decreases and saturates at a steady state charge per drop. With lubricant, the drop charge starts from 0, then it increases and reaches a maximum charge per drop. Afterward, it decreases again before reaching its steady-state value. This dependency is not a unique phenomenon for lubricant-infused PDMS; it also occurs on lubricant-infused micropillar surfaces. We attribute this dependency of charge on drop numbers to a change in surface conductivity and depletion of lubricant. These findings are helpful for understanding the charge process and optimizing solid-liquid nanogenerator devices in applications.

In this work, 1,2,4,5-benzenetetracarboxylic acid (BT) is used as a cross-linker to improve the oxidative thermostabilization of lignin-rich nanofibers so that the activated carbon nanofiber (ACNF)...

Wetting imperfections are omnipresent on surfaces. They cause contact angle hysteresis and determine the wetting dynamics. Still, existing techniques (e.g., contact angle goniometry) are not sufficient to localize inhomogeneities and image wetting variations. We overcome these limitations through scanning drop friction force microscopy (sDoFFI). In sDoFFI, a 15 μL drop of Milli-Q water is raster-scanned over a surface. The friction force (lateral adhesion force) acting on the moving contact line is plotted against the drop position. Using sDoFFI, we obtained 2D wetting maps of the samples having sizes in the order of several square centimeters. We mapped areas with distinct wetting properties such as those present on a natural surface (e.g., a rose petal), a technically relevant superhydrophobic surface (e.g., Glaco paint), and an in-house prepared model of inhomogeneous surfaces featuring defined areas with low and high contact angle hysteresis. sDoFFI detects features that are smaller than 0.5 mm in size. Furthermore, we quantified the sliding behavior of drops across the boundary separating areas with different contact angles on the model sample. The sliding of a drop across this transition line follows a characteristic stick-slip motion. We use the variation in force signals, advancing and receding contact line velocities, and advancing and receding contact angles to identify zones of stick and slip. When scanning the drop from low to high contact angle hysteresis, the drop undergoes a stick-slip-stick-slip motion at the interline. Sliding from high to low contact angle hysteresis is characterized by the slip-stick-slip motion. The sDoFFI is a new tool for 2D characterization of wetting properties, which is applicable to laboratory-based samples but also characterizes biological and commercial surfaces.

The attachment of bio-fluids to surfaces promotes the transmission of diseases. Superhydrophobic textiles may offer significant advantages for reducing the adhesion of bio-fluids. However, they have not yet found widespread use because dried remnants adhere strongly and have poor mechanical or chemical robustness. In addition, with the massive use of polymer textiles, features such as fire and heat resistance can reduce the injuries and losses suffered by people in a fire accident. We developed a superhydrophobic textile covered with a hybrid coating of titanium dioxide and polydimethylsiloxane (TiO

Metallodrugs are widely used in cancer treatment. The modification of metallodrugs with polyethylene glycol (PEGylation) prolongs blood circulation and improves drug accumulation in tumors; it represents a general strategy for drug delivery. However, PEGylation hinders cellular internalization and tumor penetration, which reduce therapeutic efficacy. Herein, the red-light-enhanced cellular internalization and tumor penetration of a PEGylated anticancer agent, PEGylated Ru complex (Ru-PEG), are reported upon. Ru-PEG contains a red-light-cleavable PEG ligand, anticancer Ru complex moiety, and fluorescent pyrene group for imaging and self-assembly. Ru-PEG self-assembles into vesicles that circulate in the bloodstream and accumulate in the tumors. Red-light irradiation induces dePEGylation and changes the Ru-PEG vesicles to large compound micelles with smaller diameters and higher zeta potentials, which enhance tumor penetration and cellular internalization. Red-light irradiation also generates intracellular

The control of liquid motion on the micrometer scale is important for many liquid transport and biomedical applications. An efficient way to trigger liquid motion is by introducing surface tension gradients on free liquid interfaces leading to the Marangoni effect. However, a pronounced Marangoni-driven flow generally only occurs at a liquid–air or liquid–liquid interface but not at solid–liquid interfaces. Using superhydrophobic surfaces, the liquid phase stays in the Cassie state (where liquid is only in contact with the tips of the rough surface structure and air is enclosed in the indentations of the roughness) and hence provides the necessary liquid–air interface to trigger evident Marangoni flows. We use light to asymmetrically heat this interface and thereby control liquid motion near superhydrophobic surfaces. By laser scanning confocal microscopy, we determine the velocity distribution evolving through optical excitation. We show that Marangoni flow can be induced optically at structured, air-entrapping superhydrophobic surfaces. Furthermore, by comparison with numerical modeling, we demonstrate that in addition to the Marangoni flow, buoyancy-driven flow occurs. This effect has so far been neglected in similar approaches and models of thermocapillary driven flow at superhydrophobic surfaces. Our work yields insight into the physics of Marangoni flow and can help in designing new contactless, light-driven liquid transport systems, e.g., for liquid pumping or in microfluidic devices.

It is challenging to treat multidrug-resistant tumors because such tumors are resistant to a broad spectrum of structurally and functionally unrelated drugs. Herein, treatment of multidrug-resistant tumors using red-light-responsive metallopolymer nanocarriers that are conjugated with the anticancer drug chlorambucil (CHL) and encapsulated with the anticancer drug doxorubicin (DOX) is reported. An amphiphilic metallopolymer PolyRuCHL that contains a poly(ethylene glycol) (PEG) block and a red-light-responsive ruthenium (Ru)-containing block is synthesized. Chlorambucil is covalently conjugated to the Ru moieties of PolyRuCHL. Encapsulation of DOX into PolyRuCHL in an aqueous solution results in DOX@PolyRuCHL micelles. The DOX@PolyRuCHL micelles are efficiently taken up by the multidrug-resistant breast cancer cell line MCF-7R and which carries DOX into the cells. Free DOX, without the nanocarriers, is not taken up by MCF-7R or pumped out of MCF-7R via P-glycoproteins. Red light irradiation of DOX@PolyRuCHL micelles triggers the release of chlorambucil-conjugated Ru moieties and DOX. Both act synergistically to inhibit the growth of multidrug-resistant cancer cells. Furthermore, the inhibition of the growth of multidrug-resistant tumors in a mouse model using DOX@PolyRuCHL micelles is demonstrated. The design of red-light-responsive metallopolymer nanocarriers with both conjugated and encapsulated drugs opens up an avenue for photoactivated chemotherapy against multidrug-resistant tumors.

Solid surfaces, in particular polymer surfaces, are able to adapt upon contact with a liquid. Adaptation results in an increase in contact angle hysteresis and influences the mobility of sliding drops on surfaces. To study adaptation and its kinetics, we synthesized a random copolymer composed of styrene and 11–25 mol% acrylic acid (PS/PAA). We measured the dynamic advancing (θA) and receding (θR) contact angles of water drops sliding down a tilted plate coated with this polymer. We measured θA ≈ 87° for velocities of the contact line

Resolving the long-standing problem of hydrate plugging in oil and gas pipelines has driven an intense quest for mechanisms behind the plug formation. However, existing theories of hydrate agglomeration have critical shortcomings, for example, they cannot describe nanometer-range capillary forces at hydrate surfaces that were recently observed by experiments. Here, we present a new model for hydrate agglomeration which includes premelting of hydrate surfaces. We treat the premelting layer on hydrate surfaces such as a thin liquid film on a substrate and propose a soft-sphere model of hydrate interactions. The new model describes the premelting-induced capillary force between a hydrate surface and a pipe wall or another hydrate. The calculated adhesive force between 0, degree a hydrate sphere (R = 300 mu m) and a solid surface varies from 0.3 mN on a hydrophilic surface (contact angle, theta = 0 degrees) to 0.008 mN on a superhydrophobic surface (theta = 160 degrees). The initial contact area is 4 orders of magnitude smaller than the cross-sectional area of the hydrate sphere and can expand with increasing contact time because of the consolidation of hydrate particles on the solid surface. Our model agrees with the available experimental results and can serve as a conceptual guidance for developing a chemical-free environmentally friendly method for prevention of hydrate plugs via surface coating of pipe surfaces.

The hypersonic phonon propagation in large-area two-dimensional colloidal crystals is probed by spontaneous micro Brillouin light scattering. The dispersion relation of thermally populated Lamb waves reveals multiband filtering due to three distinct types of acoustic band gaps. We find Bragg gaps accompanied by two types of hybridization gaps in both sub- and superwavelength regimes resulting from contact-based resonances and nanoparticle eigenmodes, respectively. The operating GHz frequencies can be tuned by particle size and depend on the adhesion at the contact interfaces. The experimental dispersion relations are well represented by a finite element method model enabling identification of observed modes. The presented approach also allows for contactless study of the contact stiffness of submicrometer particles, which reveals size effect deviating from macroscopic predictions.

Superamphiphobic surfaces are commonly associated with superior anticontamination and antifouling properties. Visually, this is justified by their ability to easily shed off drops and contaminants. However, on micropillar arrays, tiny droplets are known to remain on pillars' top faces while the drop advances. This raises the question of whether remnants remain even on nanostructured superamphiphobic surfaces. Are superamphiphobic surfaces really self-cleaning? Here we investigate the presence of microdroplet contaminants on three nanostructured superamphiphobic surfaces. After brief contact with liquids having different volatilities and surface tension (water, ethylene glycol, hexadecane, and an ionic liquid), confocal microscopy reveals a "blanket-like" layer of microdroplets remaining on the surface. It appears that the phenomenon is universal. Notably, when placing subsequent drops onto the contaminated surface, they are still able to roll off. However, adhesion forces can gradually increase by up to 3 times after repeated liquid drop contact. Therefore, we conclude that superamphiphobic surfaces do not warrant self-cleaning and anticontamination capabilities at sub-micrometric length scales.

Stretchable superamphiphobic surfaces with a high deformation resistance are in demand to achieve liquid-repellent performance in flexible electronics, artificial skin, and textile dressings. However, it is challenging to make mechanically robust superamphiphobic coatings, which maintain their superliquid repellency in a highly stretched state. Here, a stretchable superamphiphobic surface is reported, on which the microstructures can rearrange during stretching to maintain a stable superamphiphobicity even under a high tensile strain. The surface is prepared by spray-coating silicone nanofilaments onto a prestretched substrate (e.g., cis-1,4-polyisoprene) with poly(dimethylsiloxane) (PDMS) layer as a binder. After subsequent fluorination, this surface keeps its superamphiphobicity to both water and n-hexadecane up to the tensile strain of at least 225%. The binding PDMS layer and rearrangeable structures maximize the deformation resistance of the surface during the stretching process. The superamphiphobicity and morphology of the surface are maintained even after 1000 stretch-release cycles. Taking advantage of the mentioned benefits, a liquid manipulation system is designed, which has the potential for fabricating reusable and low-cost platforms for biochemical detection and lab-on-a-chip systems.

When a water drop slides over a hydrophobic surface, it usually acquires a positive charge and deposits the negative countercharge on the surface. Although the electrification of solid surfaces induced after contact with a liquid is intensively studied, the actual mechanisms of charge separation, so-termed slide electrification, are still unclear. Here, slide electrification is studied by measuring the charge of a series of water drops sliding down inclined glass plates. The glass was coated with hydrophobic (hydrocarbon/fluorocarbon) and amine-terminated silanes. On hydrophobic surfaces, drops charge positively while the surfaces charge negatively. Hydrophobic surfaces coated with a mono-amine (3-aminopropyltriethyoxysilane) lead to negatively charged drops and positively charged surfaces. When coated with a multiamine (

The force required to detach a particle from a liquid-fluid interface is a direct measure of the capillary adhesion between the particle and the interface. Analytical expressions for the detachment force are available but are limited to nonrotating particles. In this work, we derive analytical expressions for the force required to detach a rotating spherical particle from a liquid-fluid interface. Our theory predicts that the rotation reduces the detachment force when there is a finite contact angle hysteresis between the particle and the liquid. For example, the force required to detach a particle with an advancing contact angle of 120° and a receding contact angle of 80° (e.g., polydimethylsiloxane particle at a water-air interface) is expected to be 25% lower when the particle rotates while it is detached.

It is often assumed that carbon nanotubes (CNTs) stimulate neuronal differentiation by transferring electrical signals and enhancing neuronal excitability. Given this, CNT-hydrogel composites are regarded as potential materials able to combine high electrical conductivity with biocompatibility, and therefore promote nerve regeneration. However, whether CNT-hydrogel composites actually influence neuronal differentiation and maturation, and how they do so remain elusive. In this study, CNT-hydrogel composites are prepared by in situ polymerization of poly(ethylene glycol) around a preformed CNT meshwork. It is demonstrated that the composites facilitate long-term survival and differentiation of pheochromocytoma 12 cells. Adult neural stem cells cultured on the composites show an increased neuron-to-astrocyte ratio and higher synaptic connectivity. Moreover, primary hippocampal neurons cultured on composites maintain morphological synaptic features as well as their neuronal network activity evaluated by spontaneous calcium oscillations, which are comparable to neurons cultured under control conditions. These results indicate that the composites are promising materials that could indeed facilitate neuronal differentiation while maintaining neuronal homeostasis.

A large amount of energy is lost in industrial active deicing. One problem is that water retention on the surface after ice melting decreases the overall heat-transfer coefficient by up to 20%. The Miljkovic group utilizes heterogeneous biphilic surfaces to enhance defrosting performance. They avoid water retention as the slush is rapidly drawn toward the hydrophilic regions before it completely melts.

Polydimethylsiloxane (PDMS) can be linked to the surface of metal-oxide photocatalysts by immersion and UV illumination. The surfaces become hydrophobic and keep their hydrophobicity even under extended UV exposure. Titanium dioxide (TiO2) is a prominent example of a metal-oxide photocatalyst. Here, we studied the influence of a grafted PDMS layer on the photocatalytic activity and wetting properties of TiO2. By varying the molecular weight of PDMS, we controlled the thickness of the polymer layer from 0.6 to 5.5 nm. We recommend a PDMS molecular weight of 6.0 kDa. It leads to a grafted PDMS layer thickness of 2.2 nm, a receding contact angle of 94°, a low contact angle hysteresis of 9°, and the layer is still photocatalytically active.

Superparamagnetism exists only in nanocrystals, and to endow micro/macro-materials with superparamagnetism, superparamagnetic nanoparticles have to be assembled into complex materials. Most techniques currently used to produce such assemblies are inefficient in terms of time and material. Herein, we used evaporation-guided assembly to produce superparamagnetic supraparticles by drying ferrofluid droplets on a superamphiphobic substrate in the presence of an external magnetic field. By tuning the concentration of ferrofluid droplets and controlling the magnetic field, barrel-like, cone-like, and two-tower-like supraparticles were obtained. These assembled supraparticles preserved the superparamagnetism of the original nanoparticles. Moreover, other colloids can easily be integrated into the ferrofluid suspension to produce, by co-assembly, anisotropic binary supraparticles with additional functions. Additionally, the magnetic and anisotropic nature of the resulting supraparticles was harnessed to prepare magnetically actuable microswimmers.

Small particles attach to liquid-fluid interfaces due to capillary forces. The influence of rotation on the capillary force is largely unexplored, despite being relevant whenever particles roll at a liquid-fluid interface or on a moist solid. Here, we demonstrate that due to contact angle hysteresis, a particle needs to overcome a resistive capillary torque to rotate at an interface. We derive a general model for the capillary torque on a spherical particle. The capillary torque is given by M = γRLk(cos ΘR - cos ΘA), where γ is the interfacial tension, R is the radius of the particle, L is the diameter of the contact line, k = 24/π3 is a geometrical constant, and ΘR and ΘA are the receding and advancing contact angles, respectively. The expression for the capillary torque (normalized by the radius of the particle) is equivalent to the expression for the friction force that a drop experiences when moving on a flat surface. Our theory predicts that capillary torque reduces the mobility of wet granular matter and prevents small (nano/micro) particles from rotating when they are in Brownian motion at an interface.

Coatings with low sliding angles for liquid drops have a broad range of applications. However, it remains a challenge to have a fast, easy, and universal preparation method for coatings that are long-term stable, robust, and environmentally friendly. Here, a one-step grafting-from approach is reported for poly(dimethylsiloxane) (PDMS) brushes on surfaces through spontaneous polymerization of dichlorodimethylsilane fulfilling all these requirements. Drops of a variety of liquids slide off at tilt angles below 5°. This non-stick coating with autophobicity can reduce the waste of water and solvents in cleaning. The strong covalent attachment of the PDMS brush to the substrate makes them mechanically robust and UV-tolerant. Their resistance to high temperatures and to droplet sliding erosion, combined with the low film thickness (≈8 nm) makes them ideal candidates to solve the long-term degradation issues of coatings for heat-transfer surfaces.

Fast removal of small water drops from surfaces is a challenging issue in heat transfer, water collection, or anti-icing. Poly(dimethylsiloxane) (PDMS) brushes show good prospects to reach this goal because of their low adhesion to liquids. To further reduce adhesion of water drops, here, the surface to the vapor of organic solvents such as toluene or n-hexane is exposed. In the presence of such vapors, water drops slide at lower tilt angle and move faster. This is mainly caused by the physisorption of vapor and swelling of the PDMS brushes, which serves as a lubricating layer. Enhanced by the toluene vapor lubrication, the limit departure volume of water drop on PDMS brushes decreases by one order of magnitude compared to that in air. As a result, the water harvesting efficiency in toluene vapor increases by 65%. Benefits of vapor lubrication are further demonstrated for de-icing: driven by gravity, frozen water drops slide down the vertical PDMS brush surface in the presence of vapor.

Drug resistance is a major problem in cancer treatment. Herein, the design of a dual-responsive Pt(IV)/Ru(II) bimetallic polymer (PolyPt/Ru) to treat cisplatin-resistant tumors in a patient-derived xenograft (PDX) model is reported. PolyPt/Ru is an amphiphilic ABA-type triblock copolymer. The hydrophilic A blocks consist of biocompatible poly(ethylene glycol) (PEG). The hydrophobic B block contains reduction-responsive Pt(IV) and red-light-responsive Ru(II) moieties. PolyPt/Ru self-assembles into nanoparticles that are efficiently taken up by cisplatin-resistant cancer cells. Irradiation of cancer cells containing PolyPt/Ru nanoparticles with red light generates 1 O2 , induces polymer degradation, and triggers the release of the Ru(II) anticancer agent. Meanwhile, the anticancer drug, cisplatin, is released in the intracellular environment via reduction of the Pt(IV) moieties. The released Ru(II) anticancer agent, cisplatin, and the generated 1 O2 have different anticancer mechanisms; their synergistic effects inhibit the growth of drug-resistant cancer cells. Furthermore, PolyPt/Ru nanoparticles inhibit tumor growth in a PDX mouse model because they circulate in the bloodstream, accumulate at tumor sites, exhibit good biocompatibility, and do not cause side effects. The results demonstrate that the development of stimuli-responsive multi-metallic polymers provides a new strategy to overcome drug resistance.

Previous studies indicate that 2D materials such as graphene, WS2, and MoS2 deposited on oxidized silicon substrate are susceptible to aging due to the adsorption of airborne contamination. As a result, their surfaces become more hydrophobic. However, it is not clear how ubiquitous such a hydrophobization is, and the interplay between the specific adsorbed species and resultant wetting aging remains elusive. Here, we report a pronounced and general hydrophilic-to-hydrophobic wetting aging on 2D InSe films, which is independent of the substrates to synthesize these films (silicon, glass, nickel, copper, aluminum oxide), though the extent of wetting aging is sensitive to the layer of films. Our findings are ascribed to the occurrence and enrichment of airborne contamination that contains alkyl chains. Our results also suggest that the wetting aging effect might be universal to a wide range of 2D materials.

Biofilm formation is most commonly combatted with antibiotics or biocides. However, proven toxicity and increasing resistance of bacteria increase the need for alternative strategies to prevent adhesion of bacteria to surfaces. Chemical modification of the surfaces by tethering of functional polymer brushes or films provides a route toward antifouling coatings. Furthermore, nanorough or superhydrophobic surfaces can delay biofilm formation. Here we show that submicrometer-sized roughness can outweigh surface chemistry by testing the adhesion of E. coli to surfaces of different topography and wettability over long exposure times (>7 days). Gram-negative and positive bacterial strains are tested for comparison. We show that an irregular three-dimensional layer of silicone nanofilaments suppresses bacterial adhesion, both in the presence and absence of an air cushion. We hypothesize that a 3D topography can delay biofilm formation (i) if bacteria do not fit into the pores of the coating or (ii) if bending of the bacteria is required to adhere. Thus, such a 3D topography offers an underestimated possibility to design antibacterial surfaces that do not require biocides or antibiotics.

Silicones are usually considered to be inert and, thus, not reactive with surfaces. Here we show that the most common silicone, methyl-terminated polydimethylsiloxane, spontaneously and stably bonds on glass-and any other material with silicon oxide surface chemistry-even at room temperature. As a result, a 2-5 nm thick and transparent coating, which shows extraordinary nonstick properties toward polar and nonpolar liquids, ice, and even super glue, is formed. Ten microliter drops of various liquids slide off a coated glass when the sample is inclined by less than 10°. Ice adhesion strength on a coated glass is only 2.7 ± 0.6 kPa, that is, more than 98% less than ice adhesion on an uncoated glass. The mechanically stable coating can be easily applied by painting, spraying, or roll-coating. Notably, the reaction does not require any excess energy or solvents, nor does it induce hazardous byproducts, which makes it an ideal option for environmentally sustainable surface modification in a myriad of technological applications.

When a liquid drop gets into contact with a soft array of microstructures, capillary forces at the three-phase contact line can lead to critical deformations. Microstructures may collapse and form bundles or even patterns. So far, viewing the kinetics of bundling at the menisci scale has remained elusive. Here, we use laser scanning confocal microscopy to directly image the menisci between micropillars. We image structural changes in polydimethylsiloxane micropillar arrays during the Cassie-to-Wenzel transitions of a water drop evaporating on top of the array. We demonstrate how the regular pillar array undergoes a spontaneous symmetry breaking as the first step to the formation of pillar bundles. A comparison of the Cassie-to-Wenzel transition in air and FC40 indicates that the local contact angle determines the outcome of the bundling process. Based on these observations, we develop a simple model using the local contact angle, stiffness of the pillars, and interfacial tension of the liquid to predict the onset of the symmetry breaking.

To better understand the wetting of cross-linked polydimethylsiloxane (PDMS), we measured advancing and receding contact angles of sessile water drops on cross-linked PDMS as a function of contact line velocity (up to 100 μm/s). Three types of samples were investigated: pristine PDMS, PDMS where oligomers were removed by toluene treatment, and PDMS with an enriched concentration of oligomers. Depending on the velocity of advancing contact lines and the contact time with water, different modes of wetting were observed: one with a relatively low contact angle hysteresis (Δθ ≈ 10°) and one with a larger hysteresis. We attribute the low hysteresis state, called the lubricated state, to the enrichment of free oligomers at the water-PDMS interface. The enrichment of oligomers is induced by drop contact. The kinetics of the transition to the lubricated state can be described by adaptation theory. PDMS adapts to the presence of water by an enrichment of free oligomers at the interface and a correlated reduction in interfacial tension.

Janus nanoparticles could exhibit a higher interfacial activity and adsorb stronger to fluid interfaces than homogeneous nanoparticles of similar sizes. However, little is known about the interfacial diffusion of Janus nanoparticles and how it compares to that of homogeneous ones. Here, we employed fluorescence correlation spectroscopy to study the lateral diffusion of ligand-grafted Janus nanoparticles adsorbed at water/oil interfaces. We found that the diffusion was significantly slower than that of homogeneous nanoparticles. We carried out dissipative particle dynamic simulations to study the mechanism of interfacial slowdown. Good agreement between experimental and simulation results has been obtained only provided that the flexibility of ligands grafted on the nanoparticle surface was taken into account. The polymeric ligands were deformed and oriented at an interface so that the effective radius of Janus nanoparticles is larger than the nominal one obtained by measuring the diffusion in bulk solution. These findings highlight further the critical importance of the ligands grafted on Janus nanoparticles for applications involving nanoparticle adsorption at an interface, such as oil recovery or two-dimensional self-assembly.

Supraparticles consisting of nano- or microparticles have potential applications as, for example, photonic crystals, drug carriers, or heterogeneous catalysts. To avoid the use of solvent or processing liquid, one can make supraparticles by evaporating droplets of aqueous suspensions from super-liquid-repellent surfaces. Herein, a method to adjust the porosity of supraparticles is described; a high porosity is desired, for example, in catalysis. To prepare highly porous TiO2 supraparticles, polymer nanoparticles are co-dispersed in the suspension. Supraparticles are formed through evaporation of aqueous suspension droplets on superamphiphobic surfaces followed by calcination of the sacrificial polymer particles. The increase of porosity of up to 92% resulted in enhanced photocatalytic activity while maintaining sufficient mechanical stability.

Durable and biocompatible superhydrophobic surfaces are of significant potential use in biomedical applications. Here, a nonfluorinated, elastic, superhydrophobic film that can be used for medical wound dressings to enhance their hemostasis function is introduced. The film is formed by titanium dioxide nanoparticles, which are chemically crosslinked in a poly(dimethylsiloxane) (PDMS) matrix. The PDMS crosslinks result in large strain elasticity of the film, so that it conforms to deformations of the substrate. The photocatalytic activity of the titanium dioxide provides surfaces with both self-cleaning and antibacterial properties. Facile coating of conventional wound dressings is demonstrated with this composite film and then resulting improvement for hemostasis. High gas permeability and water repellency of the film will provide additional benefit for medical applications.

Many temperature-responsive polymers exhibit a single-phase transition at the lower critical solution temperature (LCST). One exception is poly(N-isopropylacryamide) (PNIPAM). PNIPAM brush layers (51 ± 3 nm thick) that are end-grafted onto glass beads collapse in two stages. The viscoelastic changes of a PNIPAM brush layers were investigated with an interferometric laser method at different temperatures. This method is able to measure the two-stage collapse of beads coated with a polymer brush layer. When these beads are situated close to a hydrophilic glass surface, they exhibit Brownian motion. As this Brownian motion changes with temperature, the collapse of the polymer layer is revealed. The characteristic spectrum of the Brownian motion of beads is modeled by a damped harmonic oscillator, where the polymer layer acts as both spring and damping elements. The change of the Brownian motion spectrum with temperature indicates two transitions of the PNIPAM brush layer, one at 36 °C and one at 46 °C. We attribute the first transition to the LCST volume collapse of PNIPAM. Here, changes of the density and viscosity of the brush dominate. The second transition is dominated by a stiffening of the brush layer.

Controlling the droplet evaporation on surfaces is desired to get uniform depositions of materials in many applications, for example, in two- and three-dimensional printing and biosensors. To explore a new route to control droplet evaporation on surfaces and produce asymmetric particles, sessile droplets of aqueous dispersions were allowed to evaporate from surfaces coated with oil films. Here, we applied 1-50 μm thick films of different silicone oils. Two contact lines were observed during droplet evaporation: an apparent liquid-liquid-air contact line and liquid-liquid-solid contact line. Because of the oil meniscus covering part of the rim of the drop, evaporation at the periphery is suppressed. Consequently, the droplet evaporates mainly in the central region of the liquid-air interface rather than at the droplet's edge. Colloidal particles migrate with the generated upward flow inside the droplet and are captured by the receding liquid-air interface. A uniform deposition ultimately forms on the substrate. With this straightforward approach, asymmetric supraparticles have been successfully fabricated independent of particle species.

The removal of hydrophobic polymer coatings from artistic surfaces is a ubiquitous challenge in art restoration. Over the years, nanostructured fluids (NSFs), aqueous surfactant solutions containing a good solvent for the polymer, have been successfully applied in polymer removal interventions; however, the precise role of the surfactant in promoting polymer film dewetting is not fully understood. This contribution addresses the interaction of a NSF of water/propylene carbonate containing a nonionic surfactant with an acrylic polymer film commonly used in art conservation. Combining confocal microscopy and fluorescence correlation spectroscopy, we monitored the penetration of the fluid into the polymer film, defining its compositional changes and following the polymer swelling. The ensemble of results highlights that the surfactant role is twofold: (i) at the polymer-support interface, it promotes the detachment of the polymer film from the underlying support; (ii) inside the polymer film, it accelerates polymer swelling by increasing the chains' mobility.

Slippery lubricant‐infused surfaces allow easy removal of liquid droplets on surfaces. They consist of textured or porous substrates infiltrated with a chemically compatible lubricant. Capillary forces help to keep the lubricant in place. Slippery surfaces hold promising prospects in applications including drag reduction in pipes or food packages, anticorrosion, anti‐biofouling, or anti‐icing. However, a critical drawback is that shear forces induced by flow lead to depletion of the lubricant. In this work, a way to overcome the shear‐induced lubricant depletion by replenishing the lubricant from the flow of emulsions is presented. The addition of small amounts of positively charged surfactant reduces the charge repulsion between the negatively charged oil droplets contained in the emulsion. Attachment and coalescence of oil droplets from the oil‐in‐water emulsion at the substrate surface fills the structure with the lubricant. Flow‐induced lubrication of textured surfaces can be generalized to a broad range of lubricant–solid combinations using minimal amounts of oil.

When a colloidal suspension droplet evaporates from a solid surface, it leaves a characteristic deposit in the contact region. These deposits are common and important for many applications in printing, coating, or washing. By the use of superamphiphobic surfaces as a substrate, the contact area can be reduced so that evaporation is almost radially symmetric. While drying, the droplets maintain a nearly perfect spherical shape. Here, we exploit this phenomenon to fabricate supraparticles from bidisperse colloidal aqueous suspensions. The supraparticles have a core-shell morphology. The outer region is predominantly occupied by small colloids, forming a close-packed crystalline structure. Toward the center, the number of large colloids increases and they are packed amorphously. The extent of this stratification decreases with decreasing the evaporation rate. Complementary simulations indicate that evaporation leads to a local increase in density, which, in turn, exerts stronger inward forces on the larger colloids. A comparison between experiments and simulations suggest that hydrodynamic interactions between the suspended colloids reduce the extent of stratification. Our findings are relevant for the fabrication of supraparticles for applications in the fields of chromatography, catalysis, drug delivery, photonics, and a better understanding of spray-drying.

The formation of a bridging gas meniscus via cavitation or nanobubbles is considered the most likely origin of the submicrometer long-range attractive forces measured between hydrophobic surfaces in aqueous solution. However, the dynamics of the formation and evolution of the gas meniscus is still under debate, in particular, in the presence of a thin air layer on a superhydrophobic surface. On superhydrophobic surfaces the range can even exceed 10 μm. Here, we report microscopic images of the formation and growth of a gas meniscus during force measurements between a superhydrophobic surface and a hydrophobic microsphere immersed in water. This is achieved by combining laser scanning confocal microscopy and colloidal probe atomic force microscopy. The configuration allows determination of the volume and shape of the meniscus, together with direct calculation of the Young-Laplace capillary pressure. The long-range attractive interactions acting on separation are due to meniscus formation and volume growth as air is transported from the surface layer.

Designing materials for water harvesting has gained much attention in recent years as water scarcity continues to be one of the biggest problems facing mankind. In this issue of ACS Nano, Xu et al. propose a new device for harvesting water from fog. They use conically shaped copper wires with periodic roughness to enhance condensation and transport of water drops. While the periodic roughness enhances drop coalescence and motion, the conical shape of the wires guides the drops in a specific direction. Together, a self-sustained water-harvesting system is described which does not require additional external stimulus but makes use of a smart design and economic production.

The nanoscopic young’s modulus of cement paste during early ages of hydration in water and nano-silica was investigated by the application of atomic force microscopy (AFM). Peak-Force Quantitative Nano-Mechanical (PFQNM) imaging mode in atomic force microscopy was used to determine elastic modulus of cement paste before and after immersion in water and nano-silica solution. The results clearly show how mechanical and physical properties of cement grains changes progressively to higher values during the hydration process in water and nano-silica. Moreover, an empirical theory on mechanism of hydration development is proposed in the current study based on experimental observations. Average Young’s modulus of condensed cement powder was changed from about 15 GPa, for unhydrated state, to 11.3 GPa after two hours of hydration in water environment. The average roughness trend was also altered from 8.31 nm to 18.2 nm during hydration process. Results show that the cement hydration rate in nano-silica solution is much higher than water environment. Moreover transition zone between C-S-H colonies have much higher mechanical properties than the hardest colonies in every ages. In the presence of nano-silica, transition zone has a width of less than 10 nm and a surface area of 5% of the overall surface area.

Controlling the structures and functions of gels is important for both fundamental research and technological applications. Introducing photoresponsive units into gels enables remote control of their properties with light. However, existing gels show photoresponsiveness only at room temperature or elevated temperatures. The development of photoresponsive gels that work below 0 °C can expand their usage in cold environments. Here, photoresponsive metallopolymer organohydrogels that function even at -20 °C are reported. The organohydrogels are prepared using photoresponsive Ru-thioether coordination bonds as reversible crosslinks to form polymer networks. A water/glycerol mixture is used as an anti-freezing solvent. At -20 °C, the Ru-thioether coordination bonds are dissociated under light irradiation and reformed reversibly in the dark, which result in alternating crosslinking densities in the polymer networks. This process enables inducing reversible gel-to-sol transitions, healing damaged gels, controlling the mechanical properties and volumes of the gels, and rewriting microstructures on the gels below 0 °C.

Controlling the organization of particles at liquid–gas interfaces usually relies on multiphasic preparations and external applied forces. Here, we show that micromolar amounts of a conventional cationic surfactant induce, in a single step, both adsorption and crystallization of various types of nanometer- to micrometer-sized anionic particles at the air–water interface, without any additional phase involved or external forces other than gravity. Contrary to conventional surfactant-induced particle adsorption through neutralization and hydrophobization at a surfactant concentration close to the critical micellar concentration (CMC), we show that in our explored concentration regime (CMC/1000-CMC/100), particles adsorb with a low contact angle and maintain most of their charge, leading to the formation of two-dimensional assemblies with different structures, depending on surfactant (Cs) and particle (Cp) concentrations. At low Cs and Cp, particles are repulsive and form disordered assemblies. Increasing Cp...

The directed, long-range and self-propelled transport of droplets on solid surfaces is crucial for many applications from water harvesting to bio-analysis1-9. Typically, preferential transport is achieved by topographic or chemical modulation of surface wetting gradients that break the asymmetric contact line and overcome the resistance force to move droplets along a particular direction10-16. Nonetheless, despite extensive progress, directional droplet transport is limited to low transport velocity or short transport distance. Here we report the high-velocity and ultralong transport of droplets elicited by surface charge density gradients printed on diverse substrates. We leverage the facile water droplet printing on superamphiphobic surfaces to create rewritable surface charge density gradients that stimulate droplet propulsion under ambient conditions17 and without the need for additional energy input. Our strategy provides a platform for programming the transport of droplets on flat, flexible and vertical surfaces that may be valuable for applications requiring a controlled movement of droplets17-19.

Perylene diimide (PDI)-based organic photovoltaic devices can potentially deliver high power conversion efficiency values provided the photon energy absorbed is utilized efficiently in charge transfer (CT) reactions instead of being consumed in nonradiative energy transfer (ET) steps. Hitherto, it remains unclear whether ET or CT primarily drives the photoluminescence (PL) quenching of the PDI excimer state in PDI-based blend films. Here, we affirm the key role of the thermally assisted PDI excimer diffusion and subsequent CT reaction in the process of PDI excimer PL deactivation. For our study we perform PL quenching experiments in the model PDI-based composite made of poly[4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b;4,5-b′]dithiophene-2,6-diyl-alt-(4-(2-ethylhexanoyl)-thieno[3,4-b]thiophene)-2-6-diyl] (PBDTTT-CT) polymeric donor mixed with the N,N′-bis(1-ethylpropyl)-perylene-3,4,9,10-tetracarboxylic diimide (PDI) acceptor. Despite the strong spectral overlap between the PDI excimer PL emission and UV-vis absorption of PBDTTT-CT, two main observations indicate that no significant ET component operates in the overall PL quenching: the PL intensity of the PDI excimer (i) increases with decreasing temperature and (ii) remains unaffected even in the presence of 10 wt % content of the PBDTTT-CT quencher. Temperature-dependent wide-angle X-ray scattering experiments further indicate that nonradiative resonance ET is highly improbable due to the large size of PDI domains. The dominance of the CT over the ET process is verified by the high performance of devices with an optimum composition of 30:70 PBDTTT-CT:PDI. By adding 0.4 vol % of 1,8-diiodooctane we verify the plasticization of the polymer side chains that balances the charge transport properties of the PBDTTT-CT:PDI composite and results in additional improvement in the device efficiency. The temperature-dependent spectral width of the PDI excimer PL band suggests the presence of energetic disorder in the PDI excimer excited state manifold.

The near-infrared (NIR) region of the spectrum is called the "therapeutic window" because NIR light can penetrate deeply into tissue. Therefore, NIR-sensitive materials are attractive for biomedical applications. Recently, upconverting nanoparticles (UCNPs) were used to construct NIR-sensitive materials. UCNPs convert NIR light to UV or visible light, which can trigger photoreactions of photosensitive materials. Here, how to use UCNPs to construct NIR-sensitive materials is introduced, applications of NIR-sensitive materials with a focus on biomedical applications are highlighted, and the associated challenges are discussed.

Many surfaces reversibly change their structure and interfacial energy upon being in contact with a liquid. Such surfaces adapt to a specific liquid. We propose the first order kinetic model to describe dynamic contact angles of such adaptive surfaces. The model is general and does not refer to a particular adaptation process. The aim of the proposed model is to provide a quantitative description of adaptive wetting and to link changes in contact angles to microscopic adaptation processes. By introducing exponentially relaxing interfacial energies and applying Young's equation locally, we predict a change of advancing and receding contact angles depending on the velocity of the contact line. Even for perfectly homogeneous and smooth surfaces, a dynamic contact angle hysteresis is obtained. As possible adaptations, we discuss changes and reconstruction of polymer surfaces or monolayers, diffusion and swelling, adsorption of surfactants, replacement of contaminants, reorientation of liquid molecules, or formation of an electric double layer.