Search

The COVID-19 pandemic has revealed the importance of the detection of airborne pathogens. Here, we present composite air filters featuring a bioinspired liquid coating that facilitates the removal of captured aerosolized bacteria and viruses for further analysis. We tested three types of air filters: commercial polytetrafluoroethylene (PTFE), which is well known for creating stable liquid coatings, commercial high-efficiency particulate air (HEPA) filters, which are widely used, and in-house-manufactured cellulose nanofiber mats (CNFMs), which are made from sustainable materials. All filters were coated with omniphobic fluorinated liquid to maximize the release of pathogens. We found that coating both the PTFE and HEPA filters with liquid improved the rate at which Escherichia coli was recovered using a physical removal process compared to uncoated controls. Notably, the coated HEPA filters also increased the total number of recovered cells by 57%. Coating the CNFM filters did not improve either the rate of release or the total number of captured cells. The most promising materials, the liquid-coated HEPA, filters were then evaluated for their ability to facilitate the removal of pathogenic viruses via a chemical removal process. Recovery of infectious JC polyomavirus, a nonenveloped virus that attacks the central nervous system, was increased by 92% over uncoated controls; however, there was no significant difference in the total amount of genomic material recovered compared to that of controls. In contrast, significantly more genomic material was recovered for SARS-CoV-2, the airborne, enveloped virus, which causes COVID-19, from liquid-coated filters. Although the amount of infectious SARS-CoV-2 recovered was 58% higher, these results were not significantly different from uncoated filters due to high variability. These results suggest that the efficient recovery of airborne pathogens from liquid-coated filters could improve air sampling efforts, enhancing biosurveillance and global pathogen early warning.

We designed and synthesized epoxy-encapsulated microparticles with core-shell structures via suspension polymerization to enable high-efficiency, room-temperature cold spray processing. The soft core of the microparticles was comprised of a thermoset resin, diglycidyl ether of bisphenol A (DGEBA), which was optionally blended with the thermoplastic, poly(butyl acrylate); the protective shell was formed using polyurea. The composition, morphology, and thermal behavior of the microparticles were investigated. An inverse relationship between deposition efficiency and particle size was demonstrated by varying the surfactant concentration that was used during particle synthesis. We also determined that the microparticles that had pure resin as the core had the lowest viscosity, exhibited a decrease in the critical impact velocity required for adhesion, had the best flowability, and yielded a dramatic increase in deposition efficiency (56%). We have demonstrated that our in-house synthesized particles can form homogeneous, smooth, and fully coalesced coatings using room-temperature cold spray.

Biofouling is a serious problem in ultrafiltration (UF) membrane applications. Modifying the surface of membranes with low molecular weight, commercially available antibacterial chemistries is an excellent strategy to mitigate biofouling. Herein, we report a new strategy to impart antibacterial and anti-biofouling behavior without changing the support membrane's size selectivity and pure water permeance (PWP). To this end, a strong antibacterial agent, cetyltrimethylammonium bromide (CTAB), was codeposited with dopamine onto commercial polyethersulfone (PES) UF membranes in the presence of nitrogen (N

Antifouling membranes that offer excellent operational lifetimes are critical technologies needed to meet the growing demand for clean water. In this study, we demonstrate antifouling membranes featuring an ultrathin oil layer that stayed immobilized on the surface and in the pore walls of poly(vinylidene fluoride) membranes for multiple cycles of operation at industrially relevant transmembrane pressures. An optimized quantity of a commercial Krytox oil with either a low (K103) or a high viscosity (K107) was infused onto the active surface and into the pores of membranes with a 0.45 μm pore size. The presence of the oil layer was qualitatively confirmed using crystal violet staining and variable pressure scanning electron microscopy. Using a dead-end stirred cell, a consistent pure water permeance value of 3000 L m

Bacterial attachment and proliferation on surfaces threaten human health and negatively impact the medical, food processing, and marine industries. In this study, we synthetically produced bioinspi...

Encapsulation technologies are imperative for the safe delivery of live bacteria into the gut where they regulate bodily functions and human health. In this study, we develop alginate-based nanofibers that could potentially serve as a biocompatible, edible probiotic delivery system. By systematically exploring the ratio of three components, the biopolymer alginate (SA), the carrier polymer poly(ethylene oxide) (PEO), and the FDA approved surfactant polysorbate 80 (PS80), the surface tension and conductivity of the precursor solutions were optimized to electrospin bead-free fibers with an average diameter of 167 ± 23 nm. Next, the optimized precursor solution (2.8/1.2/3 wt% of SA/PEO/PS80) was loaded with Escherichia coli (E. coli, 108 CFU mL-1), which served as our model bacterium. We determined that the bacteria in the precursor solution remained viable after passing through a typical electric field (∼1 kV cm-1) employed during electrospinning. This is because the microbes are pulled into a sink-like flow, which encapsulates them into the polymer nanofibers. Upon electrospinning the E. coli-loaded solutions, beads that were much smaller than the size of an E. coli were initially observed. To compensate for the addition of bacteria, the SA/PEO/PS80 weight ratio was reoptimized to be 2.5/1.5/3. Smooth fibers with bulges around the live microbes were formed, as confirmed using fluorescence and scanning electron microscopy. By dissolving and plating the nanofibers, we found that 2.74 × 105 CFU g-1 of live E. coli cells were contained within the alginate-based fibers. This work demonstrates the use of electrospinning to encapsulate live bacteria in alginate-based nanofibers for the potential delivery of probiotics to the gut.

Recent advances in memristive nanocrystal assemblies leverage controllable colloidal chemistry to induce a broad range of defect-mediated electrochemical reactions, switching phenomena, and modulate active parameters. The sample geometry of virtually all resistive switching studies involves thin film layers comprising monomodal diameter nanocrystals. Here we explore the evolution of bipolar and threshold resistive switching across highly ordered, solution-processed nanoribbon assemblies and mixtures comprising BaZrO3 (BZO) and SrZrO3 (SZO) nanocrystals. The effects of nanocrystal size, packing density, and A-site substitution on operating voltage (V-SET and V-TH) and switching mechanism were studied through a systematic comparison of nanoribbon heterogeneity (i.e., BZO-BZO vs BZO-SZO) and monomodal vs bimodal size distributions (i.e., small-small and small-large). Analysis of the current-voltage response confirms that tip-induced, trap-mediated space-charge-limited current and trap-assisted tunneling processes drive the low- and high-resistance states, respectively. Our results demonstrate that both smaller nanocrystals and heavier alkaline earth substitution decrease the onset voltage and improve stability and state retention of monomodal assemblies and bimodal nanocrystal mixtures, thus providing a base correlation that informs fabrication of solution-processed, memristive nanocrystal assemblies.

With an ever increasing scientific, technological, and industrial interest in high surface area, porous nanofiber mats, electrospinning has emerged as a popular method to produce fibrous assemblies for use across biomedical, energy, and environmental applications. However, not all precursor solutions nor complex geometries can be easily fabricated using the traditional single-nozzle apparatus. Therefore, coaxial electrospinning, a modified version of electrospinning that features a concentrically aligned dual nozzle, has been developed. This review will first describe the mechanism of electrospinning two precursor solutions simultaneously and the operational parameters that need to be optimized to fabricate continuous fibers. Modifications that can be made to the coaxial electrospinning process, which enable the fabrication of uniform fibers with improved properties, as well as the fabrication of fibers that are hollow, functionalized, and from "nonspinnable precursors" will be discussed as a means of promoting the advantages of using a coaxial setup. Examples of how coaxially electrospun nanofibers are employed in diverse applications will be provided throughout this review. We conclude with a timely discussion about the current limitations and challenges of coaxial electrospinning.

Current strategies to treat chronic wounds offer limited relief to the 7.75 million patients who suffer from burns or chronic skin ulcers. Thus, as long as chronic wounds remain a global healthcare problem, the development of alternate treatments remain desperately needed. This review explores the recent strategies employed to tailor electrospun nanofiber mats towards accelerating the wound healing process. Porous nanofiber mats readily produced by the electrospinning process offer a promising solution to the management of wounds. The matrix chemistry, surface functionality, and mat degradation rate all can be fine-tuned to govern the interactions that occur at the materials-biology interface. In this review, first we briefly discuss the wound healing process and then highlight recent advances in drug release, biologics encapsulation, and antibacterial activity that have been demonstrated via electrospinning. While this versatile biomaterial has shown much progress, commercializing nanofiber mats that fully address the needs of an individual patient remains an ambitious challenge.

Surface-associated transport of flowing bacteria, including cell rolling, is a mechanism for otherwise immobile bacteria to migrate on surfaces and could be associated with biofilm formation or the spread of infection. This work demonstrates how the moduli and/or local polymer concentration play critical roles in sustaining contact, dynamic adhesion, and transport of bacterial cells along a hydrogel or hydrated brush surface. In particular, stiffer more concentrated hydrogels and brushes maintained the greatest dynamic contact, still allowing cells to travel along the surface in flow. This study addressed how the mechanical properties, molecular architectures, and thicknesses of minimally adhesive poly(ethylene glycol) (PEG)-based coatings influence the flow-driven surface motion of Staphylococcus aureus MS2 cells. Three protein-repellant PEG-dimethylacrylate hydrogel films (∼100 μm thick) and two protein-repellant PEG brushes (8-16 nm thick) were sufficiently fouling-resistant to prevent the accumulation of flowing bacteria. However, the rolling or hopping-like motions of gently flowing S. aureus cells along the surfaces were specific to the particular hydrogel or brush, distinguishing these coatings in terms of their mechanical properties (with moduli from 2 to 1300 kPa) or local PEG concentrations (in the range 10-50% PEG). On the stiffer hydrogel coatings having higher PEG concentrations, S. aureus exhibited long runs of surface rolling, 20-50 μm in length, an increased tendency of cells to repeatedly return to some surfaces after rolling and escaping, and relatively long integrated contact times. By contrast, on the softer more dilute hydrogels, bacteria tended to encounter the surface for brief periods before escaping without return. The dynamic adhesion and motion signatures of the cells on the two brushes were bracketed by those on the soft and stiff hydrogels, demonstrating that PEG coating thickness was not important in these studies where the vertically oriented surfaces minimized the impact of gravitational forces. Control studies with similarly sized poly(ethylene oxide)-coated rigid spherical microparticles, that also did not arrest on the PEG coatings, established that the bacterial skipping and rolling signatures were specific to the S. aureus cells and not simply diffusive. Dynamic adhesion of the S. aureus cells on the PEG hydrogel surfaces correlated well with quiescent 24 h adhesion studies in the literature, despite the orientation of the flow studies that eliminated the influence of gravity on bacteria-coating normal forces.

We demonstrate antifouling ultrafiltration membranes with retained selectivity and pure water flux through the controlled deposition of zwitterionic polymers and poly(ethylene glycol) (PEG). Molecules for polymerization were immobilized on the membrane’s surface yet prevented from attaching to the membrane’s pores due to a backflow of nitrogen (N2) gas achieved using an in-house constructed apparatus that we named the polymer prevention apparatus, or “PolyPrev”. First, the operating parameters of the PolyPrev were optimized by investigating the polymerization of dopamine, which was selected due to its versatility in enabling further chemical reactions, published metrics for comparison, and its oxidative self-polymerization. Membrane characterization revealed that the polydopamine-modified membranes exhibited enhanced hydrophilicity; moreover, their size selectivity and pure water flux were statistically the same as those of the unmodified membranes. Because it is well documented that polydopamine coatings do not provide a long-lasting antifouling activity, poly(2-methacryloyloxyethyl phosphorylcholine) (polyMPC, Mn = 30 kDa) and succinimidyl-carboxymethyl-ester-terminated PEG (Mn = 40 kDa) were codeposited while dopamine was polymerizing to generate antifouling membranes. Statistically, the molecular-weight cutoff of the polyMPC- and PEG-functionalized membranes synthesized in the PolyPrev was equivalent to that of the unmodified membranes, and the pure water flux of the PEG membranes was equivalent to that of the unmodified membranes. Notably, membranes prepared in the PolyPrev with polyMPC and PEG decreased bovine serum albumin fouling and Escherichia coli attachment. This study demonstrates that by restricting antifouling chemistries from attaching within the pores of membranes, we can generate high-performance, antifouling membranes appropriate for a wide range of water treatment applications without compromising intrinsic transport properties.

By combining antifouling shark-skin patterns with antibacterial titanium dioxide (TiO2) nanoparticles (NPs), we present a simple route toward producing durable multifunctional surfaces that decrease microbial attachment and inactivate attached microorganisms. Norland Optical Adhesive, a UV-crosslinkable adhesive material, was loaded with 0, 10, or 50 wt % TiO2 NPs from which shark-skin microstructures were imprinted using solvent-assisted soft nanoimprint lithography on a poly(ethylene terephthalate) (PET) substrate. To obtain coatings with an exceptional durability and an even higher concentration of TiO2 NPs, a solution containing 90 wt % TiO2 NPs and 10 wt % tetraethyl orthosilicate was prepared. These ceramic shark-skin-patterned surfaces were fabricated on a PET substrate and were quickly cured, requiring only 10 s of near infrared (NIR) irradiation. The water contact angle and the mechanical, antibacterial, and antifouling characteristics of the shark-skin-patterned surfaces were investigated as a function of TiO2 composition. Introducing TiO2 NPs increased the contact angle hysteresis from 30 to 100° on shark-skin surfaces. The hardness and modulus of the films were dramatically increased from 0.28 and 4.8 to 0.49 and 16 GPa, respectively, by creating ceramic shark-skin surfaces with 90 wt % TiO2 NPs. The photocatalytic shark-skin-patterned surfaces reduced the attachment of Escherichia coli by ~70% compared with smooth films with the same chemical composition. By incorporating as low as 10 wt % TiO2 NPs into the chemical matrix, over 95% E. coli and up to 80% Staphylococcus aureus were inactivated within 1 h UV light exposure because of the photocatalytic properties of TiO2. The photocatalytic shark-skin-patterned surfaces presented here were fabricated using a solution-processable and roll-to-roll compatible technique, enabling the production of large-area high-performance coatings that repel and inactivate bacteria.

Correction for ‘Encapsulating bacteria in alginate-based electrospun nanofibers’ by Emily Diep et al., Biomater. Sci., 2021, 9, 4364–4373, DOI: 10.1039/D0BM02205E.

Despite lacking visual, auditory, and olfactory perception, bacteria sense and attach to surfaces. Many factors, including the chemistry, topography, and mechanical properties of a surface, are known to alter bacterial attachment, and in this study, using a library of nine protein-resistant poly(ethylene glycol) (PEG) hydrogels immobilized on glass slides, we demonstrate that the thickness or amount of polymer concentration also matters. Hydrated atomic force microscopy and rheological measurements corroborated that thin (15 μm), medium (40 μm), and thick (150 μm) PEG hydrogels possessed Young's moduli in three distinct regimes, soft (20 kPa), intermediate (300 kPa), and stiff (1000 kPa). The attachment of two diverse bacteria, flagellated Gram-negative Escherichia coli and nonmotile Gram-positive Staphylococcus aureus was assessed after a 24 h incubation on the nine PEG hydrogels. On the thickest PEG hydrogels (150 μm), E. coli and S. aureus attachment increased with increasing hydrogel stiffness. However, when the hydrogel's thickness was reduced to 15 μm, a substantially greater adhesion of E. coli and S. aureus was observed. Twelve times fewer S. aureus and eight times fewer E. coli adhered to thin-soft hydrogels than to thick-soft hydrogels. Although a full mechanism to explain this behavior is beyond the scope of this article, we suggest that because the Young's moduli of thin-soft and thick-soft hydrogels were statistically equivalent, potentially, the very stiff underlying glass slide was causing the thin-soft hydrogels to feel stiffer to the bacteria. These findings suggest a key takeaway design rule; to optimize fouling-resistance, hydrogel coatings should be thick and soft.

In this study, we exploit the excellent fouling resistance of polymer zwitterions and present electrospun nanofiber mats surface functionalized with poly(2-methacryloyloxyethyl phosphorylcholine) (polyMPC). This zwitterionic polymer coating maximizes the accessibility of the zwitterion to effectively limit biofouling on nanofiber membranes. Two facile, scalable methods yielded a coating on cellulose nanofibers: (i) a two-step sequential deposition featuring dopamine polymerization followed by the physioadsorption of polyMPC, and (ii) a one-step codeposition of polydopamine (PDA) with polyMPC. While the sequential and codeposited nanofiber mat assemblies have an equivalent average fiber diameter, hydrophilic contact angle, surface chemistry, and stability, the topography of nanofibers prepared by codeposition were smoother. Protein and microbial antifouling performance of the zwitterion modified nanofiber mats along with two controls, cellulose (unmodified) and PDA coated nanofiber mats were evaluated by dynamic protein fouling and prolonged bacterial exposure. Following 21 days of exposure to bovine serum albumin, the sequential nanofiber mats significantly resisted protein fouling, as indicated by their 95% flux recovery ratio in a water flux experiment, a 300% improvement over the cellulose nanofiber mats. When challenged with two model microbes Escherichia coli and Staphylococcus aureus for 24 h, both zwitterion modifications demonstrated superior fouling resistance by statistically reducing microbial attachment over the two controls. This study demonstrates that, by decorating the surfaces of chemically and mechanically robust cellulose nanofiber mats with polyMPC, we can generate high performance, free-standing nanofiber mats that hold potential in applications where antifouling materials are imperative, such as tissue engineering scaffolds and water purification technologies.

Corrosion causes over $100 billion in damage annually. Cinnamaldehyde, a bioactive agent derived from cinnamon bark, can mitigate the corrosion of metals but has a negative effect on hydration when incorporated in cementitious systems. In order to avoid these negative consequences while harnessing anti-corrosive properties, cinnamaldehyde was incorporated in a cementitious mixture through the use of lightweight aggregate (LWA). The same method was used for penetrating corrosion inhibitors in an attempt to reduce the time required for the inhibitor to reach and protect reinforcing steel. The setting time, compressive strength, heat evolution (via semi-adiabatic calorimetry), and autogenous shrinkage of the experimental mixtures were measured and an accelerated corrosion test (ACT) was used to quantify performance in a corrosive environment. Experimental mortars showed prolonged setting times, reduced compressive strength, heat evolution, and autogenous expansion. However, the experimental mortars showed an increase in time to cracking when exposed to a corrosive environment.

In this study, we exploit the high silver ion exchange capability of Linde Type A (LTA) zeolites and present, for the first time, electrospun nanofiber mats decorated with in-house synthesized silver (Ag(+)) ion exchanged zeolites that function as molecular delivery vehicles. LTA-Large zeolites with a particle size of 6.0 μm were grown on the surface of the cellulose nanofiber mats, whereas LTA-Small zeolites (0.2 μm) and three-dimensionally ordered mesoporous-imprinted (LTA-Meso) zeolites (0.5 μm) were attached to the surface of the cellulose nanofiber mats postsynthesis. After the three zeolite/nanofiber mat assemblies were ion-exchanged with Ag(+) ions, their ion release profiles and ability to inactivate Escherichia coli (E. coli) K12 were evaluated as a function of time. LTA-Large zeolites immobilized on the nanofiber mats displayed more than an 11 times greater E. coli K12 inactivation than the Ag-LTA-Large zeolites that were not immobilized on the nanofiber mats. This study demonstrates that by decorating nanometer to micrometer scale Ag(+) ion-exchanged zeolites on the surface of high porosity, hydrophilic cellulose nanofiber mats, we can achieve a tunable release of Ag(+) ions that inactivate bacteria faster and are more practical to use in applications over powder zeolites.

Clinically, biofilm-associated infections commonly form on intravascular catheters and other hydrogel surfaces. The overuse of antibiotics to treat these infections has led to the spread of antibiotic resistance and underscores the importance of developing alternative strategies that delay the onset of biofilm formation. Previously, it has been reported that during surface contact, bacteria can detect surfaces through subtle changes in the function of their motors. However, how the stiffness of a polymer hydrogel influences the initial attachment of bacteria is unknown. Systematically, we investigated poly(ethylene glycol) dimethacrylate (PEGDMA) and agar hydrogels that were twenty times thicker than the cumulative size of bacterial cell appendages, as a function of Young’s moduli. Soft (44.05 – 308.5 kPa), intermediate (1495 – 2877 kPa), and stiff (5152 – 6489 kPa) hydrogels were synthesized. Escherichia coli and Staphylococcus aureus attachment onto the hydrogels was analyzed using confocal microscopy after 2 and 24 hr incubation periods. Independent of hydrogel chemistry and incubation time, E. coli and S. aureus attachment correlated positively to increasing hydrogel stiffness. For example, after a 24 hr incubation period, there were 52% and 82% less E. coli adhered to soft PEGDMA hydrogels, than to the intermediate and stiff PEGDMA hydrogels, respectively. A 62% and 79% reduction in the area coverage by the Gram-positive microbe S. aureus occurred after 24 hr incubation on the soft versus intermediate and stiff PEGDMA hydrogels. We suggest that hydrogel stiffness is an easily tunable variable that, potentially, could be used synergistically with traditional antimicrobial strategies to reduce early bacterial adhesion, and therefore the occurrence of biofilm-associated infections.

In this study, we have fabricated robust patterned surfaces that contain biocompatible and antifouling stripes, which cause microorganisms to consolidate into bare silicon spaces. Copolymers of methacryloyloxyethyl phosphorylcholine (MPC) and a methacrylate-substituted dihydrolipoic acid (DHLA) were spin-coated onto silicon substrates. The MPC units contributed biocompatibility and antifouling properties, while the DHLA units enabled crosslinking and the formation of robust thin films. Photolithography enabled the formation of 200 μm wide poly(MPC-DHLA) stripped patterns that were characterized using atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and rhodamine 6G staining. Regardless of the spacing between the poly(MPC-DHLA) stripes (10, 50, or 100 μm) Escherichia coli (E. coli) rapidly adhered to the bare silicon gaps that lacked the copolymer, confirming the antifouling nature of MPC. Overall, this work provides a surface modification strategy to generate alternating bio-fouling and non-fouling surface structures that are potentially applicable for researchers studying cell biology, drug screening, and biosensor technology.

Electrospinning is a cost effective and facile method to manufacture fiber mats appropriate for biomedical applications. Due to its high molecular weight and charged backbone, hyaluronic acid (HA) fiber mats with consistent fiber morphology have been difficult to electrospin from neutral pH solutions. Here, we present that the electrospinning of HA fibers in aqueous dimethylformamide solutions is facilitated by the addition of three phosphate salts. The salts—glycerol phosphate (GP), sodium phosphate (SP), and tripolyphosphate (TPP)—facilitated electrospinning of the solutions as characterized by conductivity measurements and fiber morphology. From tensile experiments, HA mats electrospun with SP demonstrated improved Young’s modulus (12 MPa) over HA mats spun with either GP or TPP (5 and 3 MPa, respectively). This work demonstrates that a new neutral solvent system can be employed to spin HA fibers, which offers the potential for using the fibers for biomedical applications, such as a bone biomimetic.

Mechanically robust, non-toxic polymer fiber mats are promising materials for a range of biomedical applications; however, further research into enhancing polymer selection is needed. In this study, poly(allylamine) (PAH), an amine-containing polyelectrolyte, was successfully electrospun from aqueous solutions into continuous, cylindrical fibers with a mean diameter of 150 ± 41 nm. A one-step crosslinking method using glutaraldehyde provides insight into the chemical and morphological changes that result from altering the molar ratio of amine to aldehyde groups, whereas a two-step crosslinking method yielded chemically and mechanically robust mats. These results indicate PAH fibrous mats synthesized from aqueous solutions could potentially be applied in biomedical applications.

Re-engineering the support layers of membranes for forward and pressure retarded osmosis is critical for making these technologies commercially viable. Real-world applications of forward and pressure retarded osmosis, especially those involving natural and waste waters, will require membranes to withstand significant stresses. Therefore, structural changes to the support layer, which are necessary in minimizing internal concentration polarization, must not compromise its critical abilities to resist mechanical stress and provide a suitable surface for the interfacial polymerization of a robust and selective active layer. Electrospinning can provide nanofibers for support layers to potentially overcome the limitations of traditional membrane fabrication techniques in fulfilling these challenging design criteria. In this work, we present the fabrication and evaluation of thin-film composite membranes composed of electrospun polyethylene terephthalate nanofibers, a phase separation formed microporous polysulfone layer, and a polyamide selective layer formed by interfacial polymerization. These membranes have active and support layer transport properties that are suitable for engineered osmosis, with water permeability of 1.13 L m − 2 h − 1 bar − 1 (3.14 × 10 − 7 m s − 1 bar − 1 ), salt permeability of 0.23 L m − 2 h − 1 (6.4 × 10 − 8 m s − 1 ), and a structural parameter of 651 μm. Relevant and easily reproducible tests for membrane resistance to mechanical stress were performed. The use of electrospun fibers in the support layer enhanced membrane resistance to delamination at high cross-flow velocities because the 340 nm diameter electrospun fibers enmesh with the microporous polysulfone layer. A broader discussion of the most promising approaches for using electrospun materials to improve membranes for engineered osmosis is provided.

Quantifying the effect that nanofiber mat chemistry and hydrophilicity have on microorganism collection and inactivation is critical in biomedical applications. In this study, the collection and inactivation of Escherichia coli K12 was examined using cellulose nanofiber mats that were surface-functionalized using three polyelectrolytes: poly (acrylic acid) (PAA), chitosan (CS), and polydiallyldimethylammonium chloride (pDADMAC). The polyelectrolyte functionalized nanofiber mats retained the cylindrical morphology and average fiber diameter (~0.84 µm) of the underlying cellulose nanofibers. X-ray photoelectron spectroscopy (XPS) and contact angle measurements confirmed the presence of polycations or polyanions on the surface of the nanofiber mats. Both the control cellulose and pDADMAC-functionalized nanofiber mats exhibited a high collection of E. coli K12, which suggests that mat hydrophilicity may play a larger role than surface charge on cell collection. While the minimum concentration of polycations needed to inhibit E. coli K12 was 800 µg/mL for both CS and pDADMAC, once immobilized, pDADMAC-functionalized nanofiber mats exhibited a higher inactivation of E. coli K12, (~97%). Here, we demonstrate that the collection and inactivation of microorganisms by electrospun cellulose nanofiber mats can be tailored through a facile polyelectrolyte functionalization process.

In this review, we present a few of the many important objectives in the area of biomedical engineering that could open new pathways for nextgeneration biomaterials. We also provide examples of how materials for these goals can be created in an economically viable means through recent advances in high throughput production. These strategies highlight the potential for nanomanufacturing in a variety of areas of importance for human health and safety.

Biofilm-associated infections are one of the leading causes of death in the United States. Although infections may be treated with antibiotics, the overuse of antibiotics has led to the spread of antibiotic resistance. Many natural antimicrobial compounds derived from edible plants are safe for human use and target bacteria nonspecifically. Therefore, they may impair biofilm formation with less evolutionary pressure on pathogens. Here, we explore the use of two natural antimicrobial compounds, cinnamaldehyde (CA, from cinnamon) and carvacrol (CARV, from oregano), for biofilm prevention. We have fabricated and characterized films that incorporate CA and CARV into the biodegradable, FDA-approved polymer poly(lactic-co-glycolic acid), PLGA. The addition of CA and CARV to PLGA films not only adds antimicrobial activity but also changes the surface properties of the films, making them more hydrophilic and therefore more resistant to bacterial attachment. An addition of 0.1% CA to a PLGA film significantly impairs biofilm development by Staphylococcus aureus, and 0.1% CARV in PLGA significantly decreases biofilm formation by both Escherichia coli and S. aureus. Pseudomonas aeruginosa, which is less susceptible to CA and CARV, was not affected by the addition of 0.1% CA or CARV to the PLGA coatings; however, P. aeruginosa biofilm was significantly reduced by 1.0% CA. These results indicate that both CA and CARV could potentially be used in low concentrations as natural additives in polymer coatings for indwelling devices to delay colonization by bacteria.

Polymer coatings featuring nonleaching antibacterial agents are needed to significantly reduce bacterial colonization and subsequent biofilm formation. Previously, single-walled carbon nanotubes (SWNTs) have been reported to be strong antimicrobial agents that kill microbes on contact. However, the antibacterial activity of freestanding polymer mats with a low weight percent of incorporated SWNTs has not been demonstrated. In this study, four different weight percents of well characterized, small diameter (0.8 nm) SWNTs were incorporated into electrospun polysulfone (PSf) mats. Electrospun PSf-SWNT mats were observed to be flexible and composed of continuous, cylindrical, and randomly oriented fibers. SEM micrographs revealed that SWNT ends were distributed along the longitudinal fiber axis. Loss of bacteria (Escherichia coli) viability was observed to directly correlate to increased SWNT incorporation within the mat, ranging from 18% for 0.1 wt % SWNTs to 76% for 1.0 wt % SWNTs. Time-dependent bacterial cytotoxicity studies indicated that the antimicrobial action of the PSf-SWNT mats occurs after a short contact time of 15 min or less. This study demonstrates the potential applicability of electrospun PSf-SWNT mats as antibacterial coatings.

From ship hulls to bandages, biological fouling is a ubiquitous problem that impacts a wide range of industries and requires complex engineered solutions. Eliciting materials to have antibacterial or antifouling properties describes two main approaches to delay biofouling by killing or repelling bacteria, respectively. In this review article, we discuss how electrospun nanofiber mats are blank canvases that can be tailored to have controlled interactions with biologics, which would improve the design of intelligent conformal coatings or freestanding meshes that deliver targeted antimicrobials or cause bacteria to slip off surfaces. Firstly, we will briefly discuss the established and emerging technologies for addressing biofouling through antibacterial and antifouling surface engineering, and then highlight the recent advances in incorporating these strategies into electrospun nanofibers. These strategies highlight the potential for engineering electrospun nanofibers to solicit specific microbial responses for human health and environmental applications.

The fabrication and advanced function of large area biomimetic superhydrophobic surfaces (SHS) and slippery lubricant infused porous surfaces (SLIPS) are reported. The use of roll-to-roll nanoimprinting techniques enabled the continuous fabrication of SHS and SLIPS based on hierarchically wrinkled surfaces. Perfluoropolyether (PFPE) hybrid molds were used as flexible molds for roll-to-roll imprinting into a newly designed thiol-ene based photopolymer resin coated on flexible polyethylene terephthalate (PET) films. The patterned surfaces exhibit feasible superhydrophobicity with a water contact angle around 160° without any further surface modification. The SHS can be easily converted into SLIPS by roll-to-roll coating of a fluorinated lubricant, and these surfaces have outstanding repellence to a variety of liquids. Furthermore, both SHS and SLIPS display anti-biofouling properties when challenged with Escherichia coli K12 MG1655. The current report describes the transformation of artificial biomimetic structures from small, lab scale coupons to low cost, large area platforms.

Chronic wounds continue to be a global healthcare concern. Thus, the development of new nanoparticle-based therapies that treat multiple symptoms of these "non-healing" wounds without encouraging antibiotic resistance is imperative. One potential solution is to use chitosan, a naturally antimicrobial polycation, which can spontaneously form polyelectrolyte complexes when mixed with a polyanion in appropriate aqueous conditions. The requirement of at least two different polymers opens up the opportunity for us to form chitosan complexes with an additional functional polyanion. In this study, chitosan:pectin (CS:Pec) nanoparticles were synthesized using an aqueous spontaneous ionic gelation method. Systematically, a number of parameters, polymer concentration, addition order, mass ratio, and solution pH, were explored and their effect on nanoparticle formation was determined. The size and surface charge of the particles were characterized, as well as their morphology using transmission electron microscopy. The effect of polymer concentration and addition order on the nanoparticles was found to be similar to that of other chitosan:polyanion complexes. The mass ratio was tuned to create nanoparticles with a chitosan shell and a controllable positive zeta potential. The particles were stable in a pH range from 3.5 to 6.0 and lost stability after 14 days of storage in aqueous media. Due to the high positive surface charge of the particles, the innate properties of the polysaccharides used, and the harmless disassociation of the polyelectrolytes, we suggest that the development of these CS:Pec nanoparticles offers great promise as a chronic wound healing platform.

The incorporation of silver nanoparticles (AgNPs) into polymeric nanofibers has attracted a great deal of attention due to the strong antimicrobial activity that the resulting fibers exhibit. However, bactericidal efficacy of AgNP-coated electrospun fibrous mats has not yet been demonstrated. In this study, polysulfone (PSf) fibers were electrospun and surface-modified using an oxygen plasma treatment, which allowed for facile irreversible deposition of cationically charged polyethyleneimine (PEI)-AgNPs via electrostatic interactions. The PSf-AgNP mats were characterized for relative silver concentration as a function of plasma treatment time using ICP-MS and changes in contact angle. Plasma treatment of 60 s was the shortest time required for maximum loss of bacteria (Escherichia coli) viability. Time-dependent bacterial cytotoxicity studies indicate that the optimized PSf-AgNP mats exhibit a high level of inactivation against both gram negative bacteria, Escherichia coli, and gram positive bacteria, Bacillus anthracis and Staphylococcus aureus.

We report on the nanopatterning of double-bond-terminated silane (5-hexenyltrichlorosilane, HTCS) molecules on titania (TiO2) using conductive atomic force microscopy (AFM). The influences of tip electrostatic potential and scanning velocity, relative humidity and of the repeated application of voltage on the topographic height, width, and hydrophilic and hydrophobic contrast of the resultant patterns were investigated. Tip voltage and tip velocity ( v) were applied between -10 Vor= V tipor= +10 V and 100 nm/sor= vor= 2 microm/s during the lithography step(s), respectively. Average height and Lateral Force Mode (LFM) images of patterns were obtained with different values of (-10 Vor= V tipor= -7 V) and v (100 nm/sor= vor= 2 microm/s). The average height of the patterns is seen to decrease for increasing v and decreasing V tip in both a single or repeated lithography step. No patterns were observed following a single or repeated lithography step for -5 Vor= V tipor= +10 V. This conductive lithography technique results in nanoscale physiochemical manipulations of the HTCS molecules that are manifested as controllable step heights ranging from approximately 1-15 nm possessing different chemistries on the patterned and unpatterned areas. The use of conductive-AFM nanolithography for altering and manipulating double-bond-terminated molecules on TiO2 surfaces suggests a range of applications, including selective immobilization and assembly of functionalized inorganic nanoparticles and biomolecules.