Search

A glucose-reactive enzyme-based biofuel cell system (EBFC) was recently introduced in the scientific community for biomedical applications, such as implantable artificial organs and biosensors for drug delivery. Upon direct contact with tissues or organs, an implanted EBFC can exert effects that damage or stimulate intact tissue due to its byproducts or generated electrical cues, which have not been investigated in detail. Here, we perform a fundamental cell culture study using a glucose dehydrogenase (GDH) as an anode enzyme and bilirubin oxidase (BOD) as a cathode enzyme. The fabricated EBFC had power densities of 15.26 to 38.33 nW/cm 2 depending on the enzyme concentration in media supplemented with 25 mM glucose. Despite the low power density, the GDH-based EBFC showed increases in cell viability (~150%) and cell migration (~90%) with a relatively low inflammatory response. However, glucose oxidase (GOD), which has been used as an EBFC anode enzyme, revealed extreme cytotoxicity (~10%) due to the lethal concentration of H 2 O 2 byproducts (~1500 µM). Therefore, with its cytocompatibility and cell-stimulating effects, the GDH-based EBFC is considered a promising implantable tool for generating electricity for biomedical applications. Finally, the GDH-based EBFC can be used for introducing electricity during cell culture and the fabrication of organs on a chip and a power source for implantable devices such as biosensors, biopatches, and artificial organs.

Disposable screen-printed nickel/carbon composites on indium tin oxide (ITO) electrodes (DSPNCE) were developed for the detection of glucose without enzymes. The DSPNCE were prepared by screen-printing the ITO substrate with a 50 wt% nickel/carbon composite, followed by curing at 400 °C for 30 min. The redox couple of Ni(OH)₂/NiOOH was deposited on the surface of the electrodes via cyclic voltammetry (CV), scanning from 0-1.5 V for 30 cycles in 0.1 M NaOH solution. The DSPNCE were characterized by field-emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS), and electrochemical methods. The resulting electrical currents, measured by CV and chronoamperometry at 0.65 V vs. Ag/AgCl, showed a good linear response with glucose concentrations from 1.0-10 mM. Also, the prepared electrodes showed no interference from common physiologic interferents such as uric acid (UA) or ascorbic acid (AA). Therefore, this approach allowed the development of a simple, disposable glucose biosensor.

Blood glucose monitoring (BGM) using disposable electrodes is commonly used in healthcare diagnosis. The BGM method is not suitable for people with diabetes requiring real-time monitoring who might experience sudden hypoglycemia or hyperglycemia owing to a single measurement at a specific moment. This study aimed to achieve an enhanced stability of glucose diagnosis for continuous glucose measurement systems (CGMs). A representative mediator of a second-generation glucose sensor was synthesized and coordinated with a polymer for immobilization on an indium tin oxide (ITO) electrode. For electrode immobilization, an electrode for enhanced stability was fabricated using the silanization method. The morphological properties of the electrodes were confirmed via cyclic voltammetry (CV), impedance spectroscopy, and SEM. The loss rate of the current density was only 10.11% of the initial current after 8 d. The electrode exhibited a coefficient of determination of R2 = 0.9924, sensitivity of 1.5454 μA/cm2·mM, limit of quantitation (LOQ) of 7.604 μM, and limit of detection (LOD) of 2.509 μM for glucose concentrations between 0.1 and 20.0 mM. The electrode system developed in this study is applicable to the CGM healthcare industry and is expected to be applicable to biofuel cells. [ABSTRACT FROM AUTHOR]

The electrochemical-based detection of glucose is widely used for diagnostic purposes and is mediated by enzyme-mediated signal transduction mechanisms. For such applications, recent attention has focused on utilizing the oxygen-insensitive glucose dehydrogenase (GDH) enzyme in place of the glucose oxidase (GOx) enzyme, which is sensitive to oxygen levels. Currently used Ru-based redox mediators mainly work with GOx, while Ru(dmo–bpy)2Cl2 has been proposed as a promising mediator that works with GDH. However, there remains an outstanding need to improve Ru(dmo–bpy)2Cl2 attachment to electrode surfaces. Herein, we report the use of polydopamine-functionalized multi-walled carbon nanotubes (PDA-MWCNTs) to effectively attach Ru(dmo–bpy)2Cl2 and GDH onto screen-printed carbon electrodes (SPCEs) without requiring a cross–linker. PDA-MWCNTs were characterized by Fourier transform infrared (FT–IR) spectroscopy, Raman spectroscopy, and thermal gravimetric analysis (TGA), while the fabrication and optimization of Ru(dmo–bpy)2Cl2/PDA-MWCNT/SPCEs were characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements. The experimental results demonstrate a wide linear range of glucose-concentration-dependent responses and the multi-potential step (MPS) technique facilitated the selective detection of glucose in the presence of physiologically relevant interfering species, as well as in biological fluids (e.g., serum). The ease of device fabrication and high detection performance demonstrate a viable pathway to develop glucose sensors based on the GDH enzyme and Ru(dmo–bpy)2Cl2 redox mediator and the sensing strategy is potentially extendable to other bioanalytes as well. [ABSTRACT FROM AUTHOR]

An amendment to this paper has been published and can be accessed via a link at the top of the paper. [ABSTRACT FROM AUTHOR]

Direct electron transfer (DET) glucose sensors are third-generation biosensors, which allow the enzyme to directly transfer electrons by glucose oxidation without a mediator. In previous studies, many researchers have focused on the glucose oxidase (GOx)-based DET glucose sensor; however, an efficient DET glucose sensor using flavin adenine dinucleotide (FAD)-glucose dehydrogenase (GDH) has not been developed. In the present study, we bound FAD-GDH and multi-walled carbon nanotubes (MWCNT), using chitosan (CS) compounds that support hydrogen bonding, van der Waals forces, and 3D structural adsorption. The GDH/CS-MWCNT-5 composite, which had a GDH concentration of 75 wt%, was physically adsorbed on screen-printed carbon electrodes (SPCEs), and cyclic voltammetry indicated that its oxidation and reduction peaks were at − 0.422 V and − 0.543 V (vs Ag/AgCl), respectively. In addition, the electrochemical results confirmed that the prepared GDH/CS-MWCNT/SPCEs were not affected by other interfering substances or oxygen at pH of 7. The GDH/CS-MWCNT/SPCEs displayed oxidation catalytic currents, which increased according to glucose concentrations across a range of 0–5.5 mM. Finally, the short-term stability of glucose, assessed for 10 days, was maintained at 80% of the GDH enzyme activity for 6 days, and it reduced to 50% of the initial activity for the remaining 4 days. Here, we illustrate the potential utility of the FAD-GDH-based DET method in continuous glucose monitoring sensors. Diagram of the GDH/CS-MWCNT fabrication process and glucose sensing [Display omitted] • CS-MWCNTs were conjugated with FAD-GDH by hydrogen bonding. • CS-MWCNTs were optimized with GDH for DET glucose sensing. • GDH/CS-MWCNT showed good response with glucose under interfering substances. [ABSTRACT FROM AUTHOR]