Search

Reductions in the greenhouse gas (GHG) intensity of passenger and freight transportation are possible through adoption of fuel-saving technologies, demand switching between modes, and large-scale electrification of fleets, in addition to other actions. In this study, future scenarios to 2030 and 2050 are the basis for assessment of GHG reduction potentials for major passenger and freight modes (automobiles, buses, trains, aircraft, and oceangoing vessels) across eight regions of the world. New fuel-saving technologies can significantly reduce the life-cycle GHG footprint of both passenger and freight vehicles, but not uniformly worldwide. Countries outside of the Organization for Economic Cooperation and Development (OECD) lag behind OECD countries in GHG reduction potentials for all modes but oceangoing vessels owing to a combination of slower adoption of fuel-saving technologies and a slower decarbonization of electricity generation and other processes. The reduction of GHG intensity will occur more slowly for freight modes than for passenger modes. However, improved fuel efficiency has negative feedbacks to the effectiveness of mode-switching and alternative fuel adoption policies through 2050 because improvements in the fuel efficiency of vehicles alone may cause the marginal benefits of GHG abatement policies to diminish over time. This trend may be reversed if alternative fuel pathways decarbonize at faster rates than conventional transportation fuels. The largest opportunities for GHG reductions occur in non-OECD countries. Given the many factors that distinguish transportation systems between developed and developing nations (e.g., availability of new technologies, the financial ability to acquire them, and policies to incentivize their adoption), many benefits could be gained through interregional cooperation. [ABSTRACT FROM AUTHOR]

Pressure management is one cost-effective and efficient strategy for controlling water distribution losses. This paper evaluates the life-cycle energy use and emissions for pressure management zones in Philadelphia, Pennsylvania, and Halifax, Nova Scotia. It compares water savings using fixedoutlet and flow-modulated pressure control to performance without pressure control, considering the embedded electricity and chemical consumption in the lost water, manufacture of pipe and fittings to repair breaks caused by excess pressure, and pressure management. The resulting energy and emissions savings are significant. The Philadelphia and Halifax utilities both avoid approximately 130 million liters in water losses annually using flow-modulated pressure management. The conserved energy was 780 GJ and 1900 GJ while avoided greenhouse gas emissions were 50 Mg and 170 Mg a year by Philadelphia and Halifax, respectively. The life-cycle financial and environmental performance of pressure management systems compares favorably to the traditional demand management strategy of installing low-flow toilets. The energy savings may also translate to cost-effective greenhouse gas emission reductions depending on the energy mix used, an important advantage in areas where water and energy are constrained and/or expensive and greenhouse gas emissions are regulated as in California, for example. [ABSTRACT FROM AUTHOR]

This paper builds on previous research on end of life of products by synthesizing some of the theories proposed in the literature and presenting a method for environmental decision-making related to buildings. This is achieved through different solutions, but most significantly through the use of hybrid life-cycle assessment and the definition of allocation boundaries in a way that decreases the uncertainty associated with technological forecasting. Results show that there is no significant difference between the results of two major end-of-life assessment approaches (attributional and consequential), and that the choice between the use of one or the other for buildings may not be a critical decision. Assessing the impacts of recycling polices requires accounting for product substitutions, market analysis, and the full supply chain impacts of the recycling chains. Increasing the recycling of concrete from deconstructed buildings from the current 27% rate to 50% could yield a 2-3% (2.7-5.6 million metric tons of CO2 equivalents) reduction in buildings' greenhouse gas emissions, or the equivalent of removing 408,000-847,000 typical cars from U.S. roads. [ABSTRACT FROM AUTHOR]

Public transit systems with high occupancy can reduce greenhouse gas (GHG) emissions relative to low-occupancy transportation modes, but current transit systems have not been designed to reduce environmental impacts. This motivates the study of the benefits of design and operational approaches for reducing the environmental impacts of transit systems. For example, transit agencies may replace level-of-service (LOS) by vehicle miles traveled (VMT) as a criterion in evaluating design and operational changes. In previous work, we explored the unintended consequences of lowering transit LOS on emissions in a single-technology transit system. Herein, we extend the analysis to account for a more realistic case: a transit system with a hierarchical structure (trunk and feeder lines) providing service to a city where demand is elastic. By considering the interactions between the trunk and the feeder systems, we provide a quantitative basis for designing and operating integrated urban transit systems that can reduce GHG emissions and societal costs. We find that highly elastic transit demand may cancel emission reduction potentials resulting from lowering LOS, due to demand shifts to lower occupancy vehicles. However, for mass transit modes, these potentials are still significant. Transit networks with buses, bus rapid transit or light rail as trunk modes should be designed and operated near the cost-optimal point when the demand is highly elastic, while this is not required for metro. We find that the potential for unintended consequences increases with the size of the city. Our results are robust to uncertainties in the costs and emissions parameters. [ABSTRACT FROM AUTHOR]

Manufacturing accounts for 37% of the global energy demand. Few researchers have conducted a holistic energy assessment of factories where energy beyond production equipment is accounted for, and environmental impact assessments of machine tool manufacturing are even more limited. All the while, factories need to understand where energy is used, how to allocate it to their products, and where savings lie. This paper quantifies the energy consumption and greenhouse gas emissions of a machine tool manufacturer located in Iga, Japan. Six plants within the factory are investigated whose primary operations range from precision machining to product assembly. Furthermore, a model of the energy consumption of each plant's HVAC system is developed and used to evaluate the environmental impacts and operating costs at alternative sites in China, Germany, and the US. Location was found to have a significant influence on the environmental impacts and resulted in changes in the annual energy consumption relative to the Iga baseline that ranged from −10% to 8%. Additionally, opportunities for improvement were identified by comparing the energy intensities of the equipment within the plants to industrial averages. Since the plants in this study use widespread manufacturing processes and varied climates were investigated, the methods and strategies that were developed can be extended to other discrete manufacturing facilities to identify opportunities for cleaner production. [ABSTRACT FROM AUTHOR]

Passenger cars in the United States (U.S.) rely primarily on petroleum-derived fuels and contribute the majority of U.S. transportation-related greenhouse gas (GHG) emissions. Electricity and biofuels are two promising alternatives for reducing both the carbon intensity of automotive transportation and U.S. reliance on imported oil. However, as standalone solutions, the biofuels option is limited by land availability and the electricity option is limited by market adoption rates and technical challenges. This paper explores potential GHG emissions reductions attainable in the United States through 2050 with a county-level scenario analysis that combines ambitious plug-in hybrid electric vehicle (PHEV) adoption rates with scale-up of cellulosic ethanol production. With PHEVs achieving a 58% share of the passenger car fleet by 2050, phasing out most corn ethanol and limiting cellulosic ethanol feedstocks to sustainably produced crop residues and dedicated crops, we project that the United States could supply the liquid fuels needed for the automobile fleet with an average blend of 80% ethanol (by volume) and 20% gasoline. If electricity for PHEV charging could be supplied by a combination of renewables and natural-gas combined-cycle power plants, the carbon intensity of automotive transport would be 79 g CO2e per vehicle-kilometer traveled, a 71% reduction relative to 2013. [ABSTRACT FROM AUTHOR]

The formation of effective policies to reduce emissions from goods movement should consider local and remote life cycle effects as well as barriers for mode shifting. Using uni- and multimodal freight movements by truck, rail, and ocean-going vessel (OGV) associated with California, a life cycle assessment (LCA) is developed to estimate the local and remote emissions that occur from freight activity inside and associated with the state. Long-run average per tonne-kilometer results show that OGVs emit the fewest emissions, followed by rail, then trucks, and that the inclusion of life cycle processes can increase impacts by up to 32% for energy and greenhouse gas (GHG) emissions and 4,200% for conventional air pollutants. Efforts to reduce emissions through mode shifting should recognize that infrastructure and market configurations may be inimical to mode substitution. A uni- and multimodal shipping emissions assessment is developed for intrastate and California-associated freight movements to illustrate the life cycle impacts of typical trips for certain types of goods. When targeting GHG reductions in California, it should be recognized that heavy-duty trucks are responsible for 99% of intrastate goods movement emissions. An assessment of future freight truck technology improvements is performed to estimate the effectiveness of strategies to meet 2050 GHG reduction goals. Whereas aggressive improvements in fuel economy coupled with alternative vehicles and fuels can significantly reduce GHG emissions, to meet 2050 goals will likely require zero carbon emission vehicle technology. The value of using LCA in GHG reduction policy for transportation systems is explored. [ABSTRACT FROM AUTHOR]

Cellulosic ethanol can achieve estimated greenhouse gas (GHG) emission reductions greater than 80% relative to gasoline, largely as a result of the combustion of lignin for process heat and electricity in biorefineries. Most studies assume lignin is combusted onsite, but exporting lignin to be cofired at coal power plants has the potential to substantially reduce biorefinery capital costs. We assess the life-cycle GHG emissions, water use, and capital costs associated with four representative biorefinery test cases. Each case is evaluated in the context of a U.S. national scenario in which corn stover, wheat straw, and Miscanthus are converted to 1.4 EJ (60 billion liters) of ethanol annually. Life-cycle GHG emissions range from 4.7 to 61 g CO2e/MJ of ethanol (compared with ∼95 g CO2e/MJ of gasoline), depending on biorefinery configurations and marginal electricity sources. Exporting lignin can achieve GHG emission reductions comparable to onsite combustion in some cases, reduce life-cycle water consumption by up to 40%, and reduce combined heat and power-related capital costs by up to 63%. However, nearly 50% of current U.S. coal-fired power generating capacity is expected to be retired by 2050, which will limit the capacity for lignin cofiring and may double transportation distances between biorefineries and coal power plants. [ABSTRACT FROM AUTHOR]