Search

The emissivity of metallic materials is low and varies with temperature and wavelength inducing errors on surface temperature measurements. High heat flux experiments on beryllium were carried out to investigate the thermal behavior of bulk Be tiles. Thermal modeling aiming at determining the surface and bulk temperatures have been performed using ANSYS®. A Be tile was exposed to heat flux with power density ranging between 1 and 7 MW/m 2 . Surface temperatures were measured using an infrared camera in the 3–5 μm range and two-color pyrometers, one at short wavelengths (1.5–1.7 μm) and one at mid IR range wavelengths (2–4 μm) range. Both the IR camera and two-color pyrometers do not provide accurate temperature measurements on melted Be due to changes in the emissivities and emissivity ratio induced by surface modifications. [ABSTRACT FROM AUTHOR]

WEST is a full W tokamak with an extensive set of diagnostics for heat load measurements especially in the lower divertor. It is composed by infrared thermography, thermal measurement with thermocouples and fibre Bragg grating embedded few mm below the surface and flush mounted Langmuir probes. A large database including different magnetic equilibrium and input power is investigated to compare the heat load pattern (location, amplitude of the peak and heat flux decay length) on the inner and outer strike point regions: from the first ohmic diverted plasma (obtained during the second experimental campaign C2 in 2018) up to the high power (8 MW total injected) and high energy (up to 90 MJ injected energy in lower single null configuration) experiments performed in the last experimental campaign (C4 in 2019). Concerning the peak location, a good agreement (<1 cm) is obtained between thermal inversions and flush-mounted LP measurements. The peak heat flux from the whole set of diagnostics is in good agreement and mainly in the ±20% range, while the heat flux decay length reported on the target shows significant discrepancy between diagnostics and location in the machine (±40% range). Despite such discrepancy, heat flux decay length at target is found to scale mainly with the magnetic flux expansion through the variation of the X-point height, as expected. The improved plasma performances achieved during C4 enabled to reach significant heat load in the divertor, up to 6 MW m−2 with 4 MW of additional heating power showing the capability to reach the ITER relevant heat load (10 MW m−2 steady state) with about 7 MW of additional power in L-mode discharge. The heat load distribution is clearly asymmetric with a 3/4 and 1/4 distribution on the outer and inner strike point region respectively for the parallel heat flux. [ABSTRACT FROM AUTHOR]

ITER (www.iter.org) will take advantage of tungsten (W) actively cooled plasma facing units (PFUs) in the lower divertor. These PFUs will receive a steady state plasma heat flux of 10 MW m−2 and up to 20 MW m−2 in slow transients, pushing these components to their limit. For machine protection reasons and for the study of the plasma wall interactions, temperature measurements are foreseen with mid wave infra-red (MWIR: 3–5 μm) thermography systems to cover most of the ITER chamber, including the divertor (tungsten material) and first wall (beryllium material) [1]. Absolute temperature measurements from 70 °C and the cooling temperature of the PFUs, up to 3500 °C (W melting temperature at 3422 °C), are considered. Those measurements require knowledge of the emissivity of the tungsten PFU surfaces as a function of the temperature and wavelength used for the IR monochrome thermography system. This paper summarizes the emissivity measurements performed on tungsten surfaces in high heat flux test beds and the WEST tokamak [2] and uses the experimental emissivity values to compute the expected uncertainties in ITER (ΔT/T) using monochrome and bicolor thermography techniques. The results show that the monochrome technique is not able to fulfill the ΔT/T < 10% requirement, while the bicolor technique is able to reduce the temperature uncertainty below 10%. Laboratory bicolor thermography measurements using a filter wheel (including six MWIR interference filters) have been successfully performed up to 830 °C with temperature uncertainty ΔT/T < 3%. In the WEST tokamak, the two dimensions emissivity map is varying by a factor of five within 27 cm along a PFU, from 0.13 to 0.65, showing that the monochrome IR thermography will have difficulties staying within the ITER requirements ΔT/T < 10% from 70 °C up to 3500 °C. [ABSTRACT FROM AUTHOR]

Twelve ITER-like plasma-facing units made of tungsten were exposed in the WEST tokamak divertor, with three plasma-facing units (PFUs) significantly overexposed to plasma heat flux: one sharp-edged PFU (vertical misalignment h = 0.8 mm) and two chamfered PFUs (h =0.6 mm and 0.3 mm, respectively). This paper describes the first temperature analysis obtained with a very high spatial resolution infrared camera (pixel size ∼ 0.1 mm) on the misaligned PFU edges and shows the consistency obtained on the parallel heat flux derived from these measurements. The analysis is focused on the hottest areas of the PFU misaligned leading edges, since the temperature detection threshold of the VHR camera is high (Tthreshold,BB ≈ 370 °C). The heat flux parallel to the magnetic field lines is assessed by matching the toroidal temperature profile in the vicinity of the leading edge with 3D finite element modelling. The tungsten emissivity assumed in this study is 0.6, which is consistent with laboratory measurements for damaged PFUs. For the three PFUs studied (with different vertical misalignments, incident angles, geometries), the derived parallel heat flux is similar, and consistent with independent measurements by a Fiber Bragg grating embedded in a graphite PFU at another toroidal location, giving confidence in future experiments using the same settings. [ABSTRACT FROM AUTHOR]

The present paper deals with the surface heat flux estimation with thermocouples (TC) and fiber Bragg grating (FBG) embedded in the plasma facing components (PFC) of the WEST tokamak. A 2D heat transfer model combined with the conjugate gradient method and the adjoint state is used to estimate the plasma heat flux deposited on the PFC. The plasma heat flux is characterized by the time evolution of its amplitude and spatial shape on the target (heat flux decay length λ q t , power spreading in the private flux region S t and the strike point location x 0). As a first step, five ohmic pulses have been investigated with different magnetic configuration and divertor X-point height varying from 44 to 68 mm from the surface. Despite an outboard shift, the relative displacements of the outer strike point as well as the heat flux decay length derived from the TC/FBG systems are consistent with the magnetic equilibrium reconstruction. [ABSTRACT FROM AUTHOR]

• We presented the WEST full tungsten actively cooled divertor, mentioning its relevance with the ITER one. • Main features including key elements related to the large-scale production, the reception tests, and the installation into the WEST tokamak are reported. • Main manufacturing issues as well as the reception strategy, in particular the handling of non-conformities, are highlighted. • Results related to the assessment of heat removal capability by IR-thermography and high heat flux test are discussed. The WEST (W - for tungsten - Environment in Steady-state Tokamak) platform aims to support the ITER tungsten divertor technology, manufacturing and long pulse operation. For this purpose, the Tore Supra tokamak has been deeply modified (mainly the installation of a lower and upper divertor coil structure), enabling a restart in 2016 and a first phase of operation (Phase I) until the end of 2020. Following this first phase, a limited number of actively cooled PFUs (Plasma Facing Units), based on ITER divertor technology, were industrially produced and implemented into the WEST vacuum vessel. The second phase of operation (Phase II) will be with a full actively cooled divertor. The first WEST experimental campaign with this new configuration (Phase II) started in 2022. This paper reports on the key elements related to the large-scale industrial production, the reception tests, and the installation of the ITER-like divertor components (including embedded instrumentation) into the WEST tokamak. Main manufacturing issues as well as the reception strategy, in particular the handling of non-conformities, are highlighted, mentioning its relevance with ITER divertor specifications. Results related to the assessment of heat removal capability by IR thermography examination and high heat flux test, as well as the He-leak tightness control are also discussed. [ABSTRACT FROM AUTHOR]

Plasma facing components temperature measurement is required to ensure safe high power for long pulse tokamak operation and for physics studies. During the WEST phase 1, a set of 20 thermocouples (TC) and 4 fibers Bragg grating (FBG) have been exposed to five experimental campaigns with 3889 plasmas for a total plasma duration of about 7h15 and 21.2 GJ of cumulated injected energy. This paper presents the performances in terms of response time and high temperature sustaining assess with high heat flux tests performed in the HADES facility. The response time of the TC remains at the same level as before their installation in the divertor. However, the FBG have shown clear increase of their response time depending on the location due to a degradation of the thermal contact of the graphite adhesive and the FBG or component. Finally, one regenerated FBG has been exposed to high temperature, showing that absolute temperature measurement is found reliable up to 1100 °C with the start of some spectrum degradations. Full erasure of the grating is obtained after 10 s at 1200 °C well above the stable temperature of 900 °C of the regenerated FBG. [ABSTRACT FROM AUTHOR]

The main objective of WEST is to study the behavior of the ITER-like divertor monobloc components, test their resistance and ageing under ITER relevant heat loads. For the upcoming phase 2 of WEST, the lower divertor is now fully equipped with the ITER-like actively cooled bulk tungsten Plasma Facing Units (PFU), designed to withstand 10MW/m² in steady state. This divertor is also equipped with an enlarged set of ThermoCouples (TCs x 16) and Fiber Bragg Gratings (FBGs) probes (x5) with 14 measurement spots each to evaluate the heat loading during the experiments. This paper presents the new TC and FBG diagnostics as well as the associated inverse method used to estimate the surface heat flux from the embedded temperature measurements in the divertor. The performance of each diagnostic will be evaluated with synthetic measurements generated with realistic heat flux intensity and distribution. The results of a parametrical analysis shows that each diagnostic is able to estimate the spatial distribution of the expected heat fluxes in WEST. [ABSTRACT FROM AUTHOR]

Abstract: On the limiter of Tore Supra, the heat loads map computed from deconvolution of IR surface temperatures shows good agreement with calorimetry measurements. This experimental heat pattern allows deducing the heat fluxes in the scrape-off layer using a 3D magnetic calculation and assuming only parallel heat transport along field lines. This calculation leads to an underestimation of the power circulating in the edge plasma according to the power balance, similarly to RFA measurements. The comparison between experimental heat loads on the limiter and modelling also shows a spreading of heat fluxes near the LCFS that cannot be explained only by parallel transport in the SOL. [Copyright &y& Elsevier]

During the 2019 experimental campaign, the WEST tokamak was partially equipped with ITER-like plasma facing units (PFUs) made of discrete monoblocks (MBs) in one of the twelve lower divertor sectors. The magnetic field lines can enter the gaps between two MBs and strike their leading edges (LEs) with near normal incidence, leading to high localized heat flux, temperature and thermomechanical stress during both stead-state operation and transients. Exposed leading edges are a particular matter of concern because of potential crack formation, recrystallization or even melting of tungsten. During the 2019 experimental campaign in WEST, five of them were misaligned (vertical misalignment h = 0.30 ± 0.1 mm) with their poloidal leading edges exposed to the plasma heat flux. A medium wavelength IR filter (MWIR: 3.9 ± 0.1 μm) was installed in the very high resolution infrared system, featuring a submillimeter spatial resolution (∼0.1 mm/pixel). This system has a temperature detection threshold of T threshold, BB ≈ 250 °C. In this paper, thermal analysis will be presented with a specific focus on overheating of poloidal and toroidal edges using post-mortem measured emissivity maps. The study reveals an unexpected hot spot in the top LE corner of misaligned PFUs at the outer strike point (OSP). Photonic calculations were performed with different emissivity on top and lateral surfaces, in order to consider the complex reflectance characteristics in the toroidal gaps. During this experiment, the Larmor radius (0.35 mm) is comparable to the gap size. Thus, the helical trajectory of the particles may significantly affect the heat load distribution in the edges vicinity. Heat load simulations were performed with ion orbit modeling that consider the Larmor radius, to study its impact on the thermal distribution of the MB. The photonic simulations showed that it was possible to observe a false hot spot at the top LE corner, with both optical approximation (OA) and ion orbit (IO) modeling, due to reflections and different emissivity values. [ABSTRACT FROM AUTHOR]

Measuring the temperature in plasma-facing components (PFCs) provides information both on plasma parameters in the divertor region and on the thermal stress experienced by PFCs. Fiber Bragg gratings (FBGs) are interesting candidates for this application because they are immune to electromagnetic interferences and their ability to be multiplexed allows an extended spatial coverage. Four fibers, each of them including eleven regenerated Bragg gratings, have been embedded in tungsten-coated graphite components and operated up to their signal-collapsing limit at 800 °C. Extending the measurement range towards higher temperatures increases the sensitivity to plasma parameters and allows withstanding higher energy experiments. To overcome thermal limitations, the system is up-graded using femtosecond laser inscribed fibers. In addition to their outstanding thermal stability, femtosecond FBGs benefit from higher signal-to-noise ratios than regenerated FBGs. The paper addresses femtosecond FBGs design and issues relative to their integration inside the actively cooled ITER-like PFCs of the WEST tokamak. The period and length of the gratings are designed to increase the number of measurement spots to fourteen gratings per fiber, regularly distributed over 17 cm, while ensuring robust detection even with strong thermal gradients (no overlapping or deformation of Bragg peaks). The system operates up to 1200 °C with gradients reaching 200 °C/mm perpendicularly and 40 °C/mm in parallel to the fiber. FBGs are inserted in actively cooled ITER-like PFCs through a 2.5 mm deep lateral groove localized at 5 mm beneath the top of bulk tungsten monoblocks. A PFC mock-up machined with a groove has been tested under HHF facility to assess the effect of the groove on monoblocks thermal behavior. The test demonstrates that machined monoblocks behave as expected from simulation and can withstand 20 MW/m2 heat flux (i.e. 1200 °C in the fiber) with 20 % overheating as compared to intact monoblocks. [ABSTRACT FROM AUTHOR]