Search

We report that the field homogeneity of a large-scale metal-clad no-insulation all-ReBa2Cu3O7−x magnet is reproducible after occasional operating conditions, in this case the current ramp down/up and magnet warm-up/cool-down conditions. First, we shimmed the magnet by cylindrically arraying ferromagnetic shims on the wall of the room-temperature bore of the magnet to improve the spatial field homogeneity. As a result, the field homogeneity of the magnet was improved from 557.7 to 14.1 ppm in a 10 mm diameter spherical volume. The resultant acquisition of field homogeneity tremendously enhanced from an inhomogeneous state greatly degraded by screening currents qualified us to study the temporal stability of the field homogeneity. We used a magnet-energizing protocol with the field drift minimized to shrink a nuclear magnetic resonance (NMR) lineshape into a much narrower super-imposable lineshape. We demonstrate the technique by NMR experiments, showing excellent reproducibility in every case, presenting strong evidence of recovery to certain time-unvarying field gradients and to a state of homogeneity. These findings suggest a new route for high-resolution high-temperature superconducting NMR and magnetic-resonance-imaging magnet technology. [ABSTRACT FROM AUTHOR]

This paper reports the feasibility of the impregnation of no-insulation (NI) high-temperature superconducting (HTS) coils using an electrically conductive epoxy resin. Recently, several studies of HTS coils without turn-to-turn insulation have been reported for field coils used in rotating machines such as motors and generators. The NI winding technique enhances the thermal stability of the HTS coil without requiring complicated protection techniques because the quench current is automatically bypassed through the turn-to-turn contacts within the HTS coil. Nevertheless, there is still a question as to whether the NI technique can be applied to rotating machines. To utilize an HTS coil under high mechanical loads such as field coils for rotating machines, the HTS tapes must be stabilized mechanically. For HTS field coils intended for use in rotating machines, epoxy impregnation is generally necessary to protect the HTS field coil from mechanical disturbances caused by the magnetic field and rotational vibration of the rotor to enhance the mechanical stability [1], [2] . However, the NI HTS coil cannot be fabricated by wet winding using epoxy resin because epoxy resins such as Stycast 2850 FT and CTD 521 are electrically insulating materials. This study examines the electrical stability of an NI HTS coil impregnated with an epoxy resin containing electrically conductive particles. The results are likely to present useful data for the application of electrically conductive epoxy impregnated NI HTS coils to rotating machines. [ABSTRACT FROM PUBLISHER]

This paper describes new kind of HTS (High Temperature Superconducting) element for current leads, which can transfer large electric current in the nuclear fusion system. Since the HTS tapes have no resistance and the generated Joule heat is also very small compared to the conventional current leads, cooling costs of the current leads can be reduced. For this reason, the various feasibility researches for HTS current leads have been promisingly progressed in the superconducting power applications. However, there is a limitation on the capability of current carrying for single HTS tape. In addition, the cross-sectional area of the current leads should be small enough to minimize the heat conducted through the HTS current leads. In order to improve the current carrying capacity of the current leads, multiple HTS tapes are required. In this paper, we proposed several structures of compact HTS current leads and compare them other 2 kA class current leads. We report on the calculated characteristics of stabilized HTS current leads and on the performance measured during critical current measurement tests. [ABSTRACT FROM PUBLISHER]

This paper deals with the design and operating characteristics analysis of electromagnetic suspension (EMS) system. The EMS system consists of a rail, a U-shaped iron core, a high temperature superconductor (HTS) coil, a couple of DC control coils. The HTS coil generates a high magnetic field in the U-shaped iron coil and the rail. As wall as, the U-shaped iron core can be attracted by the coupled high magnetic field. We calculated turns and operating current conditions of HTS coil considering the decay of critical current when perpendicular magnetic fields are applied to the HTS coil. In addition to the design of the HTS coil, a Linear Quadratic (LQ) control method used to design the DC control coils that control the gap distance between the rail and U-shaped iron core. That is, if the gap distance is varied due to the several external disturbances, the DC control coils generated a magnetic field and then keep the constant interval. Thus, the operation of DC control coils would affect the magnetic flux density at the air gap. In this study, we verified the effect of distributions of magnetic flux density using finite element method (FEM) and MATLAB Simulink simulations. Furthermore, we numerically calculated the appropriate control current of DC control coils and the perpendicular magnetic field density on the HTS coil under the external disturbance. Based on these results, the appropriately combined current conditions and control method of EMS system to realize the stable levitation force were achieved. [ABSTRACT FROM AUTHOR]

A nuclear magnetic resonance (NMR) magnet composed of a high-temperature superconductor (HTS) is expected to contribute to a smaller size and a higher magnetic field (>1 GHz) of the NMR magnet due to its high critical current density under high magnetic field and better mechanical properties. The high operating temperature of HTS NMR magnets also makes conduction cooling by a cryocooler available. The conduction cooling system combined with a cryocooler is compact and user-friendly but has critical issues about the design of conduction cooling passages and the mechanical vibration. The small-scale HTS magnet with the conduction cooling system is fabricated and tested to check the issues and establish the design basis as a preliminary step for the development of a 400-MHz HTS NMR magnet. Thermal analysis for heat loads and thermal resistances at main joints is performed from the temperature distribution of the cooling system. The vibration levels at the crycooler and the vacuum chamber are discussed in comparison to the vibration criterion of NMR magnets. In addition, the design approach to the conduction cooling system for the HTS NMR magnet is discussed. [ABSTRACT FROM PUBLISHER]

Recently various high temperature superconducting (HTS) conductors have been commercialized in the power applications. While a BSCCO becomes tape or wire, others coated conductors (CC) are tapes. An HTS magnet utilized with these conductors can be fabricated as a form of pancake winding or layer winding. In the case of HTS magnet using a thin and rectangular tape, the pancake winding method is satisfied in the practical cases because of its suitable features. However, one of the disadvantages of this winding method is increasing brands and splices. From this point of view, we propose a layer winding method using an HTS tape and fabricated HTS layer coils. To verify the feasibility of the proposed winding method, critical current and over-current tests are investigated in liquid nitrogen and the results are compared with those of pancake coils. In addition, operating characteristics on the condition of various winding tensions are analyzed. [ABSTRACT FROM PUBLISHER]