Search

Hydrogen energy can be produced by the decomposition of hydrogen and carbon compounds. A numerical analysis method of accuracy and efficiency provides important reference value for optimizing development plans and predicting production performance of hydrogen and carbon compounds. In this work, embedded discrete fracture model (EDFM) is used to study the production performance of hydrogen and carbon compounds under non-liner seepage under the threshold pressure gradient and complex fracture systems consist of the hydraulic fractures, secondary fractures, natural fractures. A dual-permeability model of the same case is also constructed as a comparison study to analyze the development of hydrogen and carbon compounds. On this basis, the influence of threshold pressure gradient on production of hydrogen and carbon compounds is quantitatively evaluated in this paper to modify the numerical model and a novel method for the simulation of fractured hydrogen and carbon compounds reservoirs is provided. Through model comparison, the impact of fractures in the reservoir on production can reach 289.1%. A dual-permeability model of the same case is also constructed as a comparison study to analyze the development of the reservoir and the result shows a 7.9% distinction on the cumulative production. It is analyzed that when the threshold pressure gradient is increased from 0.1 MPa/m to 0.6 MPa/m, the output decline of different models ranges from 6% to 15% and a novel method improving model fidelity for the simulation of fracture reservoirs is provided. • A new numerical simulator was presented to study production performance in shale reservoirs. • Both embedded discrete fractures and the threshold pressure gradient were considered into model. • The method provides a new idea and reference for future horizontal well fracturing model. [ABSTRACT FROM AUTHOR]

Drilling infill well has been widely used in many plays to enhance the recovery of shale gas, but the infill well-caused fracture interference is a very important issue that should be taken into consideration. The well interference makes it difficult for the conventional models to make production predictions, fracture characterization, and production data analysis. In this paper, a semianalytical model is proposed for this purpose by discretizing the whole control volume of the parent and infill wells into several linear flow zones. In this way, three important issues can be further handled very naturally, including fracture connection between the parent and infill wells, different SRV properties for zones with different distances to the wellbore, and different production times for adjacent wellbores. The approximate expressions for different flow regimes are used in making production predictions in the time domain, and a flowing material balance method and a simple iteration are used to update the model parameters step by step. The proposed model is shown to be reasonable and accurate for handling multiwell interference problems after comparing with the commercial numerical simulator tNavigator. The synthetical cases show that the fracture parameters, SRV properties, and well infill time have a significant influence on the production performance of both the parent and infill wells. The results show that the production of the parent well will be dramatically enhanced when it is connected with the infill well via high-conductive hydraulic fractures. Longer unconnected fractures and more fracturing stages/clusters for the infill well will result in higher production for the infill well, but a negative effect is observed for the parent well. The permeability of the distant well SRV has a similar influence on the parent and infill wells. The results also show that late time well interference will result in a more significant increase in production rate on the log-log plots for the severe depletion around the parent well. Finally, the proposed model is used to analyze the production data of a field case from Fuling shale in Southwestern China. After analyzing the production data, several parameters can be obtained for both parent and infill wells, including the fracture lengths and conductivities, numbers of connected fractures, and the near and distant well permeabilities of the SRV. This gives a basic and practical technique for production prediction, formation and fracture evaluation, and well connectivity analysis from shale gas wells with fracture connection. [ABSTRACT FROM AUTHOR]

The presence of water, i.e., connate or hydraulic fracturing water, along with the gaseous hydrocarbons in shale nanopores is largely overlooked by previous studies. In this work, a new unified real gas-transport model has been developed for both organic and inorganic porous media accounting for the nanoconfined water film flow. More specifically, a gas core flows in the center of the organic/inorganic pore surrounded by a water film which can be further divided into an interfacial region (near-wall water) and bulk region (bulk water). We differentiate the varying water viscosity between the two regions and consider disparate slip boundaries; that is, the near-wall water can slip along the hydrophobic organic pore surface while it is negligible in hydrophilic inorganic pores. Incorporating modified boundary conditions into the Navier-Stokes equations, gas transport model through single organic/inorganic pore is derived. The model is also comprehensively scaled up to the porous media scale considering the porosity, tortuosity, and total organic carbon (TOC) contents. Results indicate that the gas flow capacity decreases in moist conditions with mobile or nonmobile water film. A mobile water film, however, compensates its negative effect up to 50% by enhancing gas flow compared with static water molecules. The real gas flow is dominated by the gas slippage and water film mobility which are dependent upon pore-scale parameters such as pore sizes, topology, pressure, and surface wettability. Compared with inorganic pores, gas transport in organic pores is greatly enhanced by the water film flow due to the strong water slip. Moreover, the contribution of water film mobility is remarkable in small pores with large contact angles, especially at high pressures. At moist conditions, the real gas effect enhances gas flow by improving both gas slippage and water film mobility, which is more prominent in smaller pores at high pressures. The presented model and its results will further advance our understanding of the mechanisms responsible for the water and gas transport in nanoporous media, and consequently, the hydrocarbon exploration of shale reservoirs. [ABSTRACT FROM AUTHOR]

To investigate the effect of thermal stimulation on shale gas recovery, a novel conceptual model coupling shale gas flow and temperature is proposed. The adsorption process is nonisothermal, and adsorption capacity changes with temperature. The local thermal nonequilibrium can explicitly describe the convective heat exchange between rock and fluids. The fluid flow model takes Knudsen diffusion, slippage effect, and non-Darcy flow into account. The complex geometry of fracture network due to hydraulic fracturing can also be considered. A series of synthetic tests are designed to demonstrate the model performance. The results show that the dynamic characteristics of heat diffusion and pressure spread can be reasonably obtained. Gas recovery decreases with the increase of volumetric heat transfer coefficient, and there exists a threshold value of the effect of volumetric heat transfer coefficient on gas recovery. Gas recovery increases with the gas and rock thermal conductivity and decreases with heat capacity of rock, but the decrease level becomes insignificant when heat capacity of rock is sufficiently high. Increasing the heating temperature and decreasing the production pressure are beneficial to enhance shale gas recovery, but the rate of recovery enhancement tends to decrease for sufficiently high heating temperature. [ABSTRACT FROM AUTHOR]

Abstract A simulation approach using the embedded discrete fracture method (EDFM) is proposed to predict the productions of multistage hydraulic fractured horizontal wells(MHFHWs)in Fuling Shale gas field in China. The approach is divided into four stages: 1) geological structure model; 2) characterize the geometry details of hydraulic and natural fractures with micro-seismic data and embedment of the fractures into structured background grids; 3) adjust the properties of effective fractures as well as other uncertain parameters by history-matching; 4) predict and analyze the performance. The proposed approach is implemented to a real case with three MHFHWs and contributes to determine the next development strategy. Highlights • Microseismic data is used to determine the hydraulic fractures distribution. • Embedded discrete fracture method (EDFM) is applied to simulate the flow in fracture network. • Component subdivision method is applied to analyze the composition of total production. • Impact factors on well performance during shale gas development are investigated in this study. [ABSTRACT FROM AUTHOR]

Fine particle migration is a crucial issue in hydraulic fracturing-based production from unconventional reservoirs and can significantly affect the effective conductivity of the packed proppant layers. In this study, to investigate the conveying behavior of fine particles, a Eulerian-Lagrangian method, namely the computational fluid dynamics–discrete element method (CFD-DEM), is adopted for 3D simulations. Two types of particles are involved in this process: larger proppant particles and fine particles. Proppant particles form a background skeleton, and a two-phase flow of fine particles and fluid is constrained in the connected pore networks. We adopt a unified CFD-DEM framework to resolve the non-slip boundary condition on the proppant particle surface and track fine particles using a four-way coupling strategy. In particular, a forcing term based on the fictitious domain method is embedded in a regular volume-averaged Navier-Stokes equation to solve the fluid motion. A perfectly packed skeleton of a face-centered cube is designed for subsequent numerical studies. The results show that the fluid and particle flow velocities are higher near the fracture surfaces than inside the interlayers. In addition, it is found that as the fine particle concentration increases, the average horizontal velocity increases, whereas the settling velocity tends to decrease. [Display omitted] • Fine particles tend to form unmovable 'fish-scale' clusters on proppant surface. • Flow velocities are higher near the fracture surfaces than inside the interlayers. • Average horizontal velocity increases with increasing fine particle concentration. • Settling velocity tends to decrease with increasing fine particle concentration. [ABSTRACT FROM AUTHOR]