Search

Fracture–cavity carbonate reservoirs account for a considerable proportion of oil and gas resources. Because of the complicated relationships between cavities, fractures and pores in these reservoirs, which are defined as cavity clusters, fracturing technology is employed to enhance their hydrocarbon productivity. However, almost all previous studies have just considered the effect of a single natural cavity or fracture on the propagation of a hydraulic fracture; therefore, the mechanism by which a hydraulic fracture interacts with a cavity cluster needs to be clarified. In this study, cavity clusters with different distributions were accurately prefabricated in synthetically made samples, and large-scale simulation equipment was employed to systematically perform fracturing experiments considering different horizontal differential stress levels. Meanwhile, the hydraulic fracture propagation behaviors were comprehensively analyzed through fracture morphology, fracturing curves, the complexity of the fracture network and acoustic emission monitoring. It was found that a natural fracture with a smaller approach angle is favorable in guiding a hydraulic fracture to a cavity. The fracturing curves were divided into the following four types: frequent fluctuations with "step-like" shapes, great fluctuations with slightly lower closure pressure, fluctuations with obviously lower closure pressure, and little fluctuations with obviously lower closure pressure. And different cavity cluster distributions play a dominant role in the complexity of generated hydraulic fracture networks. In addition, AE energy was used to judge the ease of crossing the cavity. The above findings indicated that for the actual exploration and exploitation of carbonate reservoirs, the geological exploration of different fracture–cavity structures in reservoirs would be required, and targeted fracturing engineering designs need to be carried out for different fracture–cavity carbonate reservoirs. [ABSTRACT FROM AUTHOR]

The time-dependent characteristics of reservoir performance, where deep shale (vertical depth > 3500 m) interacts with fracturing fluid at high temperature and pressure (HTHP) during or after hydraulic fracturing, are closely related to the optimal design of fracturing in adjacent sections. However, the available information on the effect of hydration under HTHP on shale properties is insufficient, especially since the interaction between fracturing fluid and shales with different mineral compositions has rarely been considered comprehensively. In this study, fluid–shale interactions under HTHP were investigated for typical marine shales with different mineral contents (clay-rich, quartz-rich, and carbonate-rich) collected from the Wufeng–Longmaxi Formation in the southern Sichuan Basin, China. The time-dependent characteristics of the mechanical, brittleness, and fracture behaviors of immersion-treated samples at different soaking times were characterized by triaxial compression tests, and X-ray microcomputed tomography (CT) scans of post-test samples. The results show that the evolution of the mechanical parameters with soaking time is different for the three types of shales. The effect of hydration under HTHP on the strength of clay-rich shale and carbonate-rich shale except for the 15-day soaking case ranges from 39.24% to 54.88% and 24.05% to 33.99%, respectively, while the effect on quartz-rich shale is relatively slight, within 20%. The effect of hydration on the shale brittleness was evaluated based on a three-part energy-based brittleness index, in descending order, clay-rich shale > carbonate-rich shale > quartz-rich shale. The crack initiation and propagation during the deformation and failure of the soaked sample are more likely to extend along the direction of the hydration crack. For cases exhibiting quasi-ductile characteristics, hydration-induced microcracks may extend over almost the entire sample, allowing locally concentrated stresses in the immersed sample to be dispersed into each crack during deformation. The experimental results can provide data support and theoretical guidance for fracturing design in deep shale gas exploration in southern Sichuan. Highlights: The evolution of the mechanical and brittleness parameters of THMC-treated shale with soaking time was characterized quantitatively. A three-part energy-based brittleness index, where each part has a well-defined physical meaning related to brittle failure, was used to characterize the shale brittleness at different soaking times. The effect of soaking time and mineral composition on the hydration-induced deterioration of shale was investigated. The deterioration mechanism of THMC-treated shales with different mineral compositions (clay-rich, carbonate-rich, and quartz-rich) was revealed. [ABSTRACT FROM AUTHOR]

Sandstone oil–gas reservoirs in the Junggar Basin, China have great development potential. However, their ultra-deep formation depth leads to high crustal stress and high breakdown pressure. Therefore, in this research, we studied the cyclic hydraulic fracturing of tight sandstone with different combinations of "high-pressure duration + low-pressure duration" under high-stress conditions. Through laboratory experiments, the pump pressure curves, hydraulic fracture morphology, acoustic emission counts, and peak frequency of the samples were obtained. The results showed that: (1) Compared with conventional hydraulic fracturing, the breakdown pressure of cyclic hydraulic fracturing was reduced by more than 30%, the minimum threshold of cyclic pump pressure required for sample breakdown was between 60%Pb and 70%Pb, and cyclic hydraulic fracturing more easily formed complex and diverse hydraulic fractures. (2) In cyclic hydraulic fracturing, under the same upper limit of cyclic pump pressure, the shorter the high-pressure duration, the fewer the cycles required for sample breakdown. (3) Under the same "high-pressure duration + low-pressure duration" condition, the lower the upper limit of the cyclic pump pressure, and the greater the number of cycles required for sample breakdown. (4) The AE cumulative counts curves fluctuated greatly during cyclic hydraulic fracturing, rising in an obvious step-wise manner and the AE peak frequency was banded and mainly divided into three parts: low frequency, medium frequency, and high frequency. [ABSTRACT FROM AUTHOR]

The formation of hydraulic fracture-network is an important goal for stable and increased production of unconventional oil and gas resources. However, due to the extremely complex mechanical behavior of hydraulic-fracture propagation, there is still a lack of fine, effective and systematic evaluation methods on 3D fracture-network structure. The quantitative characterization of hydraulic-fractures is of great significance to reveal the law of fracture propagation and to evaluate the reservoir stimulation effectiveness reasonably. Although the micro-cracks evolution process follows a random rather than deterministic pattern, the overall fracture morphology is featuring statistical regularity. In this study, after the indoor hydraulic-fracturing simulation experiments of the tight sandstone specimens, 3D optical scanning was used to visualize the fracture-network. On this basis, two aspects of quantitative statistics of 3D complex fracture-networks were established by plane and sphere cuttings for the first time, including angle distribution statistics and spatial variation statistics. Comparative analyses with reported methods showed that, the overall deflection of the macroscopic fracture-networks varies synchronously with the local roughness of the main hydraulic fractures closest to the wellbore, which satisfied exponential function or power-law function relationship between them. The variation of the area proportion with the propagation radius reflects the specific fracture propagation process such as crack initiation, bifurcation and arrest, and could be used to assess the complexity of the fracture-network. Moreover, a new stimulation evaluation index E s was established by comprehensively considering the stimulated-reservoir-area, the dispersion degree of the angle distribution and the complexity of spatial variation for 3D fracture-network. The insights gained warrant further applicability on hydraulic-fracturing in the actual engineering scale. [Display omitted] • 3D fracture-network was visualized and statistically studied based on optical scanning for the first time. • The overall deflection had a strong correlation with the local roughness of the crack initiation position. • The variation of the area proportion in the propagation direction could reflect the complexity of the fracture-network. • New stimulation evaluation index was established by considering the area and spatial distribution of 3D fracture-network. [ABSTRACT FROM AUTHOR]