Search

This article demonstrates the performance of back-to-back connected voltage source inverter (BTB-VSI)-based distribution static compensator (DSTATCOM). In the proposed system, a three-phase three wire electrical utility system (EUS) is integrated with distributed energy resources (DER) through BTB-VSI. It has drawn more attention due to enhanced active power filtering, simple design procedure and performs reliable operation. The objectives of the research work is to provide clean power for weak EUS with improved power quality (PQ) such as, better voltage regulation, improved power factor (P.F), reduced total harmonic distortion (THD), balanced voltage at point of common coupling (PCC) and better optimal active power flow control (OAPFC), and so on. An artificial neurocontrol technique Kernel Hebbian Least Mean Square (KHLMS) is chosen to determine the accurate reference source current for operation of voltage source inverter (VSI). The BTB-VSI performance is investigated on both shunt compensation and OAPFC. The proposed system is converted to a simulation model and hardware unit using MATLAB/Simulink software and SPARTAN−6 field programmable gate arrays (FPGA) controller. Finally, the Simulation and experimental results illustrate that the shunt compensating ability with OAPFC of BTB-VSI performs better over VSI as per IEEE Std 1159–2019 grid code. [ABSTRACT FROM AUTHOR]

This article proposes an adaptive Kernel-Hebbian least mean square (KHLMS) controller for a dual voltage source inverter (VSI). The recommended topology consists of a distributed energy resource (DER) supported VSI called main VSI (MVSI) and split capacitor supported VSI termed as auxiliary VSI (AVSI). Both the MVSI and AVSI are used to serve the shunt compensation when DER is not integrated with MVSI. The DER scenario is considered to suppress the active power flow shortage in the utility grid. Here, optimal active power flow control (OAPFC) is managed by MVSI and shunt compensation is achieved by AVSI during DER operated mode. Hence, a dual VSI based distribution static compensator (DSTATCOM) facilitates the configuration merits such as reduction in system downtime cost, filter rating switching stress etc. Supremacy of both the neural network (NN) based controller and topology is presented by comparing VSI (called AVSI) in the context of harmonic reduction in source side, voltage balancing, power factor (PF) enhancement, better voltage regulation and OAPFC. The experimental results are obtained through field programmable gate array (FPGA) based hardware units which exhibit radical improvement in the power quality (PQ) conferring as per the international standard grid code (IEEE-519-2017). [ABSTRACT FROM AUTHOR]

This paper presents a dual voltage source inverter (DVSI)-based Distributed Static Compensator (DSTATCOM) to enhance the power quality in the power utility system (PUS). The proposed DSTATCOM consists of two numbers of two-level voltage source inverters (VSI) which controls the reactive power. One of them is regarded as the main voltage source inverter (MVSI) and the other is considered as auxiliary voltage source inverter (AVSI). The i cos ⁡ ϕ control algorithm is employed to generate the reference source currents as well as switching pulses. The detailed control algorithm is formulated by mathematical analysis using MATLAB/Simulink, and compared with different case studies. Among all the theoretical findings, the DVSI offers better voltage regulation, voltage balancing, source current harmonic reduction and power factor correction under various loading scenarios. Apart from these, reliability, stress balancing of the both MVSI and AVSI, cost reduction due to a decrease in the filter size and better operation of PUS is obtained. To check the effectiveness, the performance of the DVSI-based DSTATCOM is carried out as per the benchmark value of the IEEE-519-2014 and IEC-61000-1 grid code. [ABSTRACT FROM AUTHOR]

A new hybrid control technique called gradient descent back propagation (GDBP)-based i cos ø for a three phase twolevel distribution static compensator (DSTATCOM) to perform the functions such as harmonic mitigation, power factor correction under reactive loads, which further reduces the DC link voltage across the self-supported capacitor of voltage source converter (VSC). The weighted value of fundamental active and reactive components of load currents are extracted using the proposed control technique to generate the reference source currents. Furthermore, these currents are used to trigger the VSC of the DSTATCOM. The effectiveness of this control technique is demonstrated through simulation using MATLAB/SIMULINK and sim power system tool boxes. The real-time implementation of DSTATCOM is also realised by real-time digital simulator. These results reveal the robustness of the proposed DSTATCOM as it is showing outstanding harmonic compensation capabilities under the various loading conditions and keeping the total harmonics distortion of the source current well <5%, the limit imposed by IEEE-519 standard. [ABSTRACT FROM AUTHOR]