Search

The main contribution of this paper is the assets of the current and voltage ripples in a buck converter with an LED load. The results indicate that the ripples are different and that it is possible to reduce the passive filter concerning the model of the LED as a simple resistance. The paper presents the design and simulation of a buck converter as a power supply for an LED lamp. Modeling the LED as a resistor and a voltage source (SVRM), the equations to calculate the components of the circuit using the SVRM model are presented, where the Fourier series and phasors are used to calculate the output filter. The equations are validated with SPICE simulations. The results indicate that the SVRM model for the LED load affects the calculation of the output filter of the buck converter as well as the voltage and current ripples, making it a more precise design alternative to the proposed development. [ABSTRACT FROM AUTHOR]

Currently, the design of resonant power converters has only been developed while operating in the steady state, while the design operating in the transient stage has not been considered nor reported. This paper is interested in testing the performance of the resonant circuits operating in the transient stage and finding applications where benefits can be obtained from this form of operation. One application in which it is possible to obtain benefits from designing resonant circuits in the transient state is in the area of frequency multiplication. Usually, to achieve frequency multiplication, it is necessary to resort to complex methods and special devices that increase the complexity of the design and the total cost of the circuit. This paper evaluates the performance of a series RLC resonant circuit operating in the transient stage and with an underdamped response acting as a frequency multiplier, where the oscillation frequency of the current in the resonant tank is "n" number of times the switching frequency of the square voltage source at the input with a duty cycle of D = 50%. To validate the analysis, a circuit was designed to deliver an output power of 30 watts to a resistive load, where the switching frequency of the square voltage source at the input was 500 kHz. Since a multiplier value "n" equal to fifteen was chosen, the current in the resonant tank reached an oscillation frequency of 7.5 MHz. The design methodology was validated by simulations in SPICE, complying with the established design parameters. [ABSTRACT FROM AUTHOR]

The main contribution of this study is to show the effect of light-emitting diode (LED) modelling in the design of offline drives. The authors propose the use of a source voltage and resistance model (SVRM), consisting of a threshold voltage source in series with the characteristic resistance, for the modelling of the LED. The offline drive used for the analysis is the flyback converter operating in discontinuous conduction mode. The equivalent circuit is analysed by superposition and the AC circuit is analysed with phasors. The analysis has proven that the flyback converter can be modelled as a current source feeding the output capacitor in parallel with the load. Likewise, the analysis demonstrated that the current ripple is always greater than the voltage ripple when an LED is used as a load. In order to validate the theoretical analysis, a design methodology for the flyback converter with the SVRM as a load was developed. The designed circuit was simulated in Spice and implemented in a prototype. Experimental results using an LED as load are compared with the same circuit using a simple resistance as load. The experimental results confirm the theoretical analysis with an error of <6.6%. [ABSTRACT FROM AUTHOR]

The arrangement of the full-bridge, current-source inverter as a power supply for ozone generators providing high power factor (PF) and high electrical efficiency in a single stage is the main contribution of this paper. The corresponding design, simulation, and experimental results are presented. Also, the use of the current-fed, full-bridge resonant inverter for PF correction in ozone generation applications is discussed. The proposed power supply consists of an ac supply, a single rectifier bridge, an input inductor to the inverter, four switches, an LC parallel resonant tank, a resonant transformer, and a set of ozone generating cells. Experimental results with the proposed topology provided 96% for PF, 91% for electrical efficiency, and ozone production of 614 mgO3/min, satisfying the requirements of the standard 61000-3-2, class A. [ABSTRACT FROM AUTHOR]

This paper presents a theoretical analysis of a DC-DC flyback converter variant applied in energy harvesting based on thermoelectric generators. The main contribution of the article is the analysis and obtaining the equations of the behavior of the converter with a rearrangement of the elements of the traditional flyback converter in such a way that the converter only processes part of the energy while the other part is delivered directly to the load. This is achieved by connecting the secondary of the flyback in series with the load, and this assembly, in turn, is placed in parallel with the primary and the voltage source. This configuration means that the topology can only be a boost topology; however, there are benefits such as partial power processing (R2P2) and reduced stress on converter components in both voltage and current; all this leads to increase the efficiency. A Low Frequency Averaging Analysis (LFAA) was used to determine the behavior of the proposed circuit, and a simple equivalent circuit to analyze was obtained. In order to validate the theoretical analysis, a circuit was simulated in Spice and implemented in an 18 W prototype. Experimental results showed that the converter has an efficiency of 92.65%. Moreover, the rearranged flyback processed only 56% of the input power. [ABSTRACT FROM AUTHOR]

The main contribution of this paper is to show a new AC/DC converter based on the rearrangement of the flyback converter. The proposed circuit only manages part of the energy and the rest is delivered directly from the source to the load. Therefore, with the new topology, the efficiency is increased, and the stress of the components is reduced. The rearrangement consist of the secondary of the flyback is placed in parallel with the load, and this arrangement is connected in series with the primary side and the rectified voltage source. The re-arranged flyback is only a reductive topology and with no magnetic isolation. It was studied as a power supply for LEDs. A low frequency averaged analysis (LFAA) was used to determine the behavior of the proposed circuit and an equivalent circuit much easier to analyze was obtained. To validate the theoretical analysis, a design methodology was developed for the re-arranged flyback converter. The designed circuit was implemented in a 10 W prototype. Experimental results showed that the converter has a THDi = 21.7% and a PF = 0.9686. [ABSTRACT FROM AUTHOR]