Search

Four-switch buck–boost converter supports both voltage step-up and step-down functionalities, but it suffers from mode transfer challenge that would need reliable mode detection when designed to operate in multidifferent modes. In this article, a novel control method based on model predictive current control is proposed for such converter with inherent smooth mode transfer capability without extra design on mode detection and transfer scheme. Modulator and mode detection are replaced by an optimization process through cost function. This largely simplifies the design and makes it easily implemented. Seamless transfer between buck and boost modes is achieved with many other system level benefits. Simulation and experimental results are provided to verify the effectiveness of proposed method for the four-switch buck–boost converter. [ABSTRACT FROM AUTHOR]

A discrete-time average model-based predictive control (DTA-MPC) is proposed for a quasi-Z-source inverter (qZSI). As a single-stage inverter topology, the qZSI regulates the dc-link voltage and the ac output voltage through the shoot-through (ST) duty cycle and the modulation index. Several feedback strategies have been dedicated to produce these two control variables, among which the most popular are the proportional–integral (PI)-based control and the conventional model-predictive control (MPC). However, in the former, there are tradeoffs between fast response and stability; the latter is robust, but at the cost of high calculation burden and variable switching frequency. Moreover, they require an elaborated design or fine tuning of controller parameters. The proposed DTA-MPC predicts future behaviors of the ST duty cycle and modulation signals, based on the established discrete-time average model of the quasi-Z-source (qZS) inductor current, the qZS capacitor voltage, and load currents. The prediction actions are applied to the qZSI modulator in the next sampling instant, without the need of other controller parameters’ design. A constant switching frequency and significantly reduced computations are achieved with high performance. Transient responses and steady-state accuracy of the qZSI system under the proposed DTA-MPC are investigated and compared with the PI-based control and the conventional MPC. Simulation and experimental results verify the effectiveness of the proposed approach for the qZSI. [ABSTRACT FROM PUBLISHER]

The battery energy-stored quasi-Z-source (BES-qZS)-based photovoltaic (PV) power generation system combines advantages of the qZS inverter and the battery energy storage system. However, the second-harmonic ( \text2\omega ) power ripple degrades the system's performance and affects the system's design. An accurate model to analyze the \text2\omega ripple is very important. The existing models did not consider the battery, or assumed a symmetric qZS network with $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$, which limits the design freedom and causes oversized impedance parameters. This paper proposes a comprehensive model for the single-phase BES-qZS-PV inverter system, where the battery is considered and there is no restriction of $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$ . Based on the built model, a BES-qZS impedance design method is proposed to mitigate the \text2\omega ripple with asymmetric qZS network. Simulation and experimental results verify the proposed \text2\omega ripple model and impedance design method. [ABSTRACT FROM AUTHOR]

A quasi-Z-source modular cascaded converter (qZS-MCC) is proposed for dc integration of high-power photovoltaic (PV) systems. The qZS-MCC comprises series-connected front-end isolated qZS half-bridge (HB) dc–dc converter submodules (SMs). With the front-end isolation, the qZS-MCC achieves high-voltage dc capability, while maintaining modularity and PV panel grounded. The post-stage qZS-HB handles the PV voltage and power flows, dc-link voltage balance, and output-series power integration. Whereas, the front-end isolation converters of all SMs perform a constant duty cycle, lowing the control complexity. There is no double-line-frequency power flowing through the dc-side PV panels, qZS inductors, and qZS capacitors in the qZS-MCC, so small qZS impedance is possible compared to the existing qZS cascaded multilevel inverter. The configuration, operating principle, power loss evaluation, and passive components design of the proposed system are investigated in this part of the paper. The system control, modeling, and corresponding verifications are stated in Part II of this paper. [ABSTRACT FROM PUBLISHER]

The second harmonic pulsating power flows through the dc side of a single-phase quasi-Z-source inverter (qZSI), which requires bulky capacitor banks and inductors to suppress low-frequency ripple of dc-link voltage and inductor currents in the passive ripple reduction way. However, the resultant huge qZS network seriously deteriorates the system reliability, efficiency, volume, weight, and cost. This paper proposes an active-filter-integrated single-phase qZSI to transfer low-frequency power ripple directly from ac load to active filter's ac capacitor, so that low-frequency power ripple does not present in dc side anymore and constant inductor currents and constant capacitor voltages are ensured. Thus, much small qZS impedance is employed to only smooth high-frequency ripple and active filter's capacitor supports ac voltage (large ripple allowed) with small capacitance. The operation principle, parameter design method, and modeling and control strategy of the proposed topology are investigated. Comparative evaluation, simulation, and experimental results verify the proposed new topology system. [ABSTRACT FROM PUBLISHER]

The single-phase quasi-Z source inverter (qZSI) topology has recently attracted attention for single-phase grid-tie photovoltaic (PV) applications. However, due to the inherent second-harmonic power flow in single-phase systems, a large qZS network is required to reduce the second-harmonic component of currents and voltages on the dc side. Minimization of the qZS network remains an open issue. This paper proposes a technique that minimizes the qZS capacitance and inductance of the single-phase qZSI topology by employing dc-side low-frequency current ripple damping control. Through analysis of power flow, a second-harmonic power model is derived and the ripple power is analyzed for minimization of the qZS network. A current ripple damping control is proposed to ensure suppression of second-harmonic power flow through the inductors. Simulation and experimental results verify the theoretical analysis, damping control, and the proposed design minimization of the qZS network for the single-phase topology. [ABSTRACT FROM PUBLISHER]

The second harmonic $(2\omega)$ power ripple of single-phase quasi-Z-source (qZS) photovoltaic (PV) inverter highly affects the whole system's design and performance. The topology's $2\omega$ ripple model is very important to analyze qZS PV inverter's $2\omega$ voltage and current ripple. The existing models did not consider the PV-panel dynamic and terminal capacitors, which causes the theoretical results apart from the truth. In this paper, a comprehensive modeling for single-phase qZS-PV inverter is proposed, where the $2\omega$ ripple model of the qZS-PV inverter system with a real PV source is established and discussed without and with a PV terminal capacitor. The influences from qZS inductance and capacitance, and PV-panel terminal capacitance to the $2\omega$ voltage and current ripple are investigated using the built model. The system parameter design method is proposed to mitigate this ripple. Simulation and experimental results validate the proposed $2\omega$ ripple model and parameter design method. [ABSTRACT FROM PUBLISHER]

The quasi-Z-source cascaded multilevel inverter (qZS-CMI) presented many advantages over conventional CMI when applied in photovoltaic (PV) power systems. For example, qZS-CMI provides the balanced dc-link voltage and voltage boost ability, saves one-third modules, etc. However, current research studies only disclosed control of single-phase qZS-CMI-based PV power systems, and there was no literature related to control of three-phase qZS-CMI-based PV power systems. In this paper, for the first time, three-phase qZS-CMI's control is proposed and demonstrated for application to PV power systems. The models of PV-panel-fed qZS H-bridge module and qZS-CMI-based PV power system are built to accurately design control algorithms for each module and the whole system. The proposed control method includes the distributed maximum power point tracking for each module, dc-link peak voltage balance control for all modules, and grid-tie control for the whole system; moreover, a new multilevel space vector modulation method is proposed for the three-phase qZS-CMI. Simulation and experimental results on a test bench with a three-phase seven-level qZS-CMI-based PV power system verify the proposed control and modulation methods. [ABSTRACT FROM PUBLISHER]

The quasi- $Z$ source (qZS) cascaded multilevel inverter (CMI) (qZS-CMI) presents attractive advantages in application to photovoltaic (PV) power system. Each PV panel connects to an H-bridge qZS inverter (qZSI) to form a power generation module. The distributed maximum power point tracking and all modules' dc-link peak voltage balance can be achieved. However, it is the same with the conventional CMI that the second-harmonic ( $2\omega$) voltage and current ripples exist in each qZSI module. It is crucial for a qZS-CMI to design the reasonable qZS network parameters to limit the ripples within a desired range. This paper proposes an analytic model to accurately calculate the $2\omega$ voltage and current ripples of each qZSI module. A qZS impedance design method based on the built model is proposed to limit the $2\omega$ ripples of dc-link voltage and inductor current. Simulated and experimental results through using the designed 1.5-kW prototype validate the proposed analytic model and the design method. Furthermore, this paper analyzes all of the operating states for a qZSI module and calculates the power loss. The measured efficiency from the prototype verifies the theoretical calculation, and the qZS-CMI-based grid-tie PV power system is tested in practical. [ABSTRACT FROM PUBLISHER]