Search

Magnetized liner inertial fusion (MagLIF) is a fusion concept that uses magnetized, preheated fuel to reduce the implosion velocities and convergence ratios required for ignition. A scaled, laser-driven experimental platform to study MagLIF has been demonstrated on the OMEGA laser system, providing comprehensive experimental data on MagLIF scaling, utilizing the higher shot rate on OMEGA compared to the Z machine. Using this platform, a broader experimental space for MagLIF has been studied. Presented in this article are experimental results that demonstrate that the combination of preheat and magnetization enhances the neutron yield by 470% compared to a reference implosion, significantly more than the yield enhancement by the field or preheat alone. These results are achieved while maintaining a relatively low convergence ratio (<20). The experiments were supported by one-, two-, and three-dimensional radiation-hydrodynamics simulations, all of which suggest that multiple sources of mix play different key roles depending on the scale of the MagLIF experiment. [ABSTRACT FROM AUTHOR]

Cryogenic deuterium–tritium ice target implosions on OMEGA with new small-spot (SG5-650) distributed phase plates (DPPs) achieved an (11 ± 4) % increase in energy coupling compared to implosions with larger-spot SG5-850 DPPs by decreasing the ratio of the laser spot diameter to the target diameter from 0.93 to 0.75. The SG5-650 DPPs provide a focus spot size of 674 μm, which is defined as the diameter that encircles 95% of the measured beam energy compared to 834 μm for the SG5-850, which are the standard DPPs in cryogenic target implosions on OMEGA. The hydrodynamic efficiency, defined as the ratio of the kinetic energy in the imploding shell to the laser energy, increased from 4.5% to 5.0% based on radiation-hydrodynamic calculations benchmarked to shell trajectory and bang-time measurements. The higher coupling came with a trade-off of an increased hot-electron production as well as increased hydrodynamic instabilities seeded by a larger mode-10 amplitude from the beam port geometry, both of which may have reduced the fusion neutron production and areal density. [ABSTRACT FROM AUTHOR]

Laser heating of a gas in a cylindrical liner held in by a thin foil window is a critical process in the MagLIF (magnetized liner inertial fusion) concept [S. A. Slutz and R. A. Vesey, Phys. Rev. Lett. 108, 025003 (2012)]. Window burnthrough and gas heating for OMEGA scale MagLIF cylinders as a function of time have been determined using spectrally integrated soft x-ray diagnostics. Window laser absorption is classified in terms of the emitted x-rays from the window plasma as a function of laser energy and shows that the laser energy absorbed is weakly dependent on incident intensity. Radiation–hydrodynamic simulations overestimate the amount of laser energy absorbed by the window as evidenced by the increase in x-ray radiation across several photon energy bands compared to experiments. Gas temperatures inferred from soft x-ray emission from the front 1mm of the liner are shown to evolve in time in a similar manner to simulation predictions. Soft x-ray emission from the gas within the region of the liner that is normally imploded is shown to meet the 100 eV requirements set by the initial point design for laser-driven MagLIF. [ABSTRACT FROM AUTHOR]

Low-density foams of low-/mid-Z materials have been previously proposed to mitigate laser imprint for direct-drive inertial confinement fusion (ICF). For foam densities above the critical density of the drive laser, the mechanism of laser-imprint mitigation relies on the reduced growth rate of Rayleigh–Taylor instability because of the increased ablation velocity and density scale length at the ablation surface. Experimental demonstration of this concept has been limited so far to planar-target geometry. The impact of foams on spherical implosions has not yet been explored in experiments. To examine the viability of using an above-critical-density foam layer to mitigate laser-imprint effects in direct-drive ICF implosions on OMEGA, we have performed a series of 2-D DRACO simulations with state-of-the-art physics models, including nonlocal thermal transport, cross-beam energy transfer, and first-principles equation-of-state tables. The simulation results indicate that a 40-μm-thick CH or SiO2 foam layer with a density of ρ = 40 mg/cm3 added to a D2-filled polystyrene (CH) capsule can significantly improve the moderate-adiabat (α ≈ 3) implosion performance. In comparison to the standard CH target implosion, an increase in neutron yield by a factor of 4 to 8 and the recovery of 1-D compression ρR are predicted by DRACO simulations for a foam-target surface roughness of σrms ≤ 0.5 μm. These encouraging results could readily facilitate experimental demonstrations of laser-imprint mitigation with an above-critical-density foam layer. [ABSTRACT FROM AUTHOR]

Laser-driven magnetized liner inertial fusion (MagLIF) is being developed on the OMEGA Laser System to study scaling. MagLIF targets require a preheat laser entrance window that can hold the gas in the target yet allow sufficient laser energy to enter the gas. For OMEGA MagLIF targets, 1.8-μm-thick polyimide foils were found to be sufficient to hold a fuel pressure of up to 14 atm. Transmission and reflection of an OMEGA beam incident on such foils were measured with a calorimeter and time-resolved spectrometers for 2.5-ns square-shaped pulses, with energies from 60 to 200 J, focused to intensities from 0.65 to 2.2 × 1014 W/cm2. The laser energy transmitted in every case exceeded that required to achieve the goal of preheating the gas to 100 eV. The time-resolved measurements showed an initial period with very low, decreasing transmission, the duration of which decreased with increasing intensity, followed by a rapid transition to full transmission, accompanied by brief sidescattering of the transmitted light with a significant red shift. Reflection was always negligible. Two-dimensional radiation–hydrodynamic simulations, using 3-D ray tracing with inverse bremsstrahlung energy deposition, did not capture the rapid transition to full transmission, showing instead a slow increase in transmission, without significant sidescatter or red shift. We propose that full transmission is achieved by self-focusing followed by ponderomotive blowout of the plasma. [ABSTRACT FROM AUTHOR]

To support direct-drive inertial confinement fusion experiments at the National Ignition Facility (NIF) [G. H. Miller, E. I. Moses, and C. R. Wuest, Opt. Eng. 43, 2841 (2004)] in its indirect-drive beam configuration, the polar-direct-drive (PDD) concept [S. Skupsky et al., Phys. Plasmas 11, 2763 (2004)] has been proposed. Ignition in PDD geometry requires direct-drive-specific beam smoothing, phase plates, and repointing the NIF beams toward the equator to ensure symmetric target irradiation. First experiments to study the energetics and preheat in PDD implosions at the NIF have been performed. These experiments utilize the NIF in its current configuration, including beam geometry, phase plates, and beam smoothing. Room-temperature, 2.2-mm-diam plastic shells filled with D2 gas were imploded with total drive energies ranging from ~500 to 750 kJ with peak powers of 120 to 180 TW and peak on-target irradiances at the initial target radius from 8 × 1014 to 1.2 × 1015 W/cm². Results from these initial experiments are presented, including measurements of shell trajectory, implosion symmetry, and the level of hot-electron preheat in plastic and Si ablators. Experiments are simulated with the 2-D hydrodynamics code DRACO including a full 3-D ray-trace to model oblique beams, and models for nonlocal electron transport and cross-beam energy transport (CBET). These simulations indicate that CBET affects the shell symmetry and leads to a loss of energy imparted onto the shell, consistent with the experimental data. [ABSTRACT FROM AUTHOR]