Search

Experimental results from indirectly driven inertial confinement fusion experiments testing the performance gained from using an alternate capsule tent support are reported. The polar tent describes an alternate geometry for the thin membrane used to support the Deuterium–Tritium (DT) filled capsule. Here, the contact area is reduced by 23 times by locating the tent support close to the poles of the capsule. The polar tent experiments are repeats of previous 3 shock 1.63 MJ, 400 TW high foot experiments and use a 165 μm thick silicon doped carbon hydrogen plastic (CH) shell. Using the polar tent support, we report a DT neutron yield of 1.07 × 10 16 , 76% higher than the expected Y D T ∝ V 7.7 scaling. This is, at the time of writing, the highest neutron yield to date from a CH shell implosion. Furthermore, we find that the inferred pressure when using the polar tent is significantly above the model based on analytic scaling even when accounting for tent effects. Analysis of x-ray and neutron images shows the reduction of lobes produced by nominal tent features. The reduction of these features in the polar tent experiments leads to decreased low mode (P2 and P4) asymmetry compared to the nominal tent results. [ABSTRACT FROM AUTHOR]

In indirectly driven Inertial Confinement Fusion implosions conducted on the National Ignition Facility (NIF), the imploding capsule is supported in a laser-heated radiation enclosure (called a “hohlraum”) by a pair of very thin (∼15–45 nm) plastic films (referred to as a “tent”). Even though the thickness of these tents is a small fraction of that of the spherical capsule ablator (∼165 μm), both numerical simulations as well as experiments indicate that this capsule support mechanism results in a large areal density (ρR) perturbation on the capsule surface at the contact point where the tent departs from the capsule. As a result, during deceleration of the deuterium-tritium (DT) fuel layer, a jet of the dense ablator material penetrates and cools the fuel hot spot, significantly degrading the neutron yield (resulting in only ∼10%–20% of the unperturbed 1-D yield). In this article, we present a hypothesis and supporting design simulations of a new “polar contact” tent support system, which reduces the contact area between the tent and the capsule and results in a significant improvement in the capsule performance. Simulations predict a ∼70% increase in neutron yield over that for an implosion with a traditional tent support. An initial demonstration experiment was conducted on the NIF and produced highest ever recorded primary DT neutron yield among all layered DT implosions with plastic ablators on the NIF, though more experiments are needed to comprehensively study the effect of the polar tent on implosion performance. [ABSTRACT FROM AUTHOR]

We report a reduced X-ray shadow imprint of hydrodynamic instabilities on the high-density carbon ablator surface of inertial confinement fusion (ICF) capsules using a reduced diameter fuel fill tube on the National Ignition Facility (NIF). The perturbation seed mass from hydrodynamic instabilities was reduced by approximately an order of magnitude by reducing both the diameter and wall thickness of the fill tube by ∼2×, consistent with analytical estimates. This work demonstrates a successful mitigation strategy for engineered features for ICF implosions on the NIF. [ABSTRACT FROM AUTHOR]

Hydrodynamic instability growth has been studied using three-dimensional (3-D) broadband modulations by comparing "high-foot" and "low-foot" spherical plastic (CH) capsule implosions at the National Ignition Facility (NIF) [E. M. Campbell et al., AIP Conf. Proc. 429, 3 (1998)]. The initial perturbations included capsule outer-surface roughness and capsule-mounting membranes ("tents") that were similar to those used in a majority of implosions on NIF. The tents with thicknesses of 31-nm, 46-nm, and 109-nm were used in the experiments. The outer-surface roughness in the "lowfoot" experiment was similar to the standard specification, while it was increased by ~4 times in the "high-foot" experiment to compensate for the reduced growth. The ablation-front instability growth was measured using a Hydrodynamic Growth Radiography platform at a convergence ratio of ~3. The dominant capsule perturbations, generated by the tent mountings, had measured perturbation amplitudes comparable to the capsule thickness with the "low-foot" drive. These tent perturbations were reduced by ~3 to 10 times in implosions with the "high-foot" drive. Unexpectedly, the measured perturbations with initially thinner tents were either larger or similar to the measured perturbations with thicker tents for both "high-foot" and "low-foot" drives. While the measured instability growth of 3-D broadband perturbations was also significantly reduced by ~5 to 10 times with the "high-foot" drive, compared to the "low-foot" drive, the growth mitigation was stronger than expected based on previous "growth-factor" results measured with two-dimensional modulations [D. T. Casey et al., Phys. Rev. E 90, 011102 (2014)]. One of the hypotheses to explain the results is based on the 3-D modulations of the oxygen content in the bulk of the capsule having a stronger effect on the overall growth of capsule perturbations than the outer-surface capsule roughness. [ABSTRACT FROM AUTHOR]