Search

In this study, a cost‐effective HVDC shunt tap with low‐number of relatively low‐voltage semiconductor devices and small‐sized passive components is proposed. The proposed architecture is based on employing three single‐phase half‐bridge Modular Multilevel Converters (MMCs), where the DC sides of MMCs are connected in series across the total DC‐link voltage. The MMCs are adopted instead of conventional Two‐Level Voltage Source Converters (2L‐VSCs) to avoid the complications of series connection of Insulated Gate Bipolar Transistors (IGBTs). The involved MMCs in the suggested architecture are operated with the conventional 2L modulation, which results in insignificant arm inductors and Sub‐Modules (SMs) capacitances (in range of µH and µF, respectively). This, in turn, affects positively the converter cost and footprint. Each arm of the involved MMCs can be considered as a high‐voltage valve of a 2L‐VSC. To maintain the balance of SMs capacitors, each arm of the involved (N + 1)‐level MMC has an extra SM (a balancing SM) to select N out of N + 1 SMs during the turn‐off condition. The operational concept, design, and assessment of the proposed architecture are presented in this study. Simulation results are provided for substantiation of the proposed concept. Finally, a scaled down single‐phase prototype is used for experimental validation. [ABSTRACT FROM AUTHOR]

This paper proposes a medium-/high-voltage high-power hybrid modular dc–dc converter to interconnect two different dc-voltage levels in medium-/high-voltage dc grids. The converter consists of half-bridge submodules (SMs) rated at a moderate voltage level, i.e., series connection of semiconductor devices is avoided while connecting two high dc-voltage levels. The proposed architecture provides self-balancing operation, i.e., unlike conventional modular converters, no need for capacitor voltage measurement, which enhances the system reliability and simplicity. Sequential charging/discharging of SMs capacitors is adopted in the proposed approach to ensure a self-balanced operation. The proposed architecture can provide a high conversion ratio as well as power transfer in both directions, i.e., bidirectional dc–dc converter. Detailed illustration of the proposed approach operational concept, design, and overall control system is presented. Simulation and experimental results are presented to show the viability of the proposed configuration and validate the claims. [ABSTRACT FROM AUTHOR]

Highlights • A new switching pattern is proposed for zero voltage switching of hybrid modular dc-dc converter. • The switching losses is greatly reduced by enabling operation with ZVS of the involved HV valve. • The dynamic voltage sharing of series-connected IGBTs based HV valve is simplified as the switching occurs at zero voltage. Abstract In this paper, a bidirectional non-isolated hybrid modular DC–DC converter for high-voltage (HV) applications is investigated. In this configuration, conventional Half-Bridge Sub-Modules (HB-SMs) are employed. The proposed DC–DC converter is based on connecting the SMs capacitors in series across the high DC voltage level while connecting them sequentially across the low DC voltage level. On another frontier, an HV valve, based on series-connected Insulated-Gate Bipolar Transistors (IGBTs), is required at the HV side. The main confronted challenge of the series-connected IGBTs is the voltage sharing during turn-on and turn-off periods, which necessitates the engagement of an intricate voltage sharing technique. In this work, a switching pattern is proposed to ensure zero-voltage switching (ZVS) of the involved HV valve. In order to reduce the switching losses and avoid complex active gate control recruited for dynamic voltage sharing, the zero-voltage state is extended beyond the switching time. A detailed illustration of the hybrid modular DC–DC converter is presented, elucidating the proposed switching pattern. Simulation results, using Matlab/Simulink platform, are presented to validate the contribution of the paper. Finally, a scaled-down prototype is employed for experimental verification. [ABSTRACT FROM AUTHOR]

In this paper, a dc–ac buck converter is proposed as a grid-side converter in high voltage dc (HVdc) transmission systems for high-power renewable energy source grid integration. The proposed architecture consists of multimodules of half-bridge voltage source converters (HB-VSCs). The dc terminals of the HB-VSCs are connected in series across the entire dc link (i.e., capacitor tapped), whereas their ac outputs are connected to multiwinding transformers to provide the three-phase terminals for ac grid integration. The proposed grid-connected capacitor-tapped multimodule converter (CT-MC) architecture, inspired from the HVdc shunt tap proposed by ABB, provides a dc–ac conversion with a relatively moderate voltage rating of semiconductor devices. It also provides operation with a lower number of semiconductor devices, gate driver circuits, voltage sensors, and lower total MVA rating of semiconductor devices (67%) compared with the conventional three-phase HB modular multilevel converter, which positively affects the system cost and reduces the computational burden of the employed controller. In this paper, the operational concept and control of the CT-MC are presented along with a capacitor voltage balancing approach. Simulation results are presented during normal and abnormal conditions to show the viability of the proposed architecture. Finally, a scaled down prototype for the CT-MC is employed to validate the converter operation. [ABSTRACT FROM AUTHOR]

The conventional unipolar Marx generator can be employed for bipolar pulsed electric field by adding a high-voltage H-bridge at the load side which necessitates stacked switches. Alternatively, bipolar Marx generator with low-voltage switches can be employed. The existing bipolar Marx generators are typically fed from dc supplies, where polarized capacitors are employed. The capacitance of involved capacitors is selected such that the total energy stored in the generator's capacitors is higher than the bipolar pulse energy. As a result, polarized capacitors with relatively high capacitances are required. In addition, a high number of controlled switches per stage are required (at least four switches per stage). In this paper, a new solid-state bipolar Marx pulse generator with only three controlled switches per stage is proposed. The proposed generator is fed from sinusoidal/square ac voltage and non-polarized capacitors with low capacitance are employed. The proposed bipolar Marx-generator can be used effectively with resistive loads for exponential pulse generation. A detailed illustration of the proposed approach is presented and a discussion, to elucidate the differences between the proposed pulse generator and the other existing ones, are presented. Simulation results for the proposed pulse generator are presented to validate the concept. Finally, experimental results have been obtained from a low-voltage model of the proposed generator. [ABSTRACT FROM AUTHOR]

Pulsed electric field is a commonly used and effective disinfection method in drinking water treatment applications. In this paper, a transformerless unipolar/bipolar high-voltage pulse generator is presented with well-regulated pulsed output voltage for drinking water treatment via underwater pulsed corona discharge. The proposed high-voltage pulse generator is fed from a relatively low-voltage dc supply. Then, capacitor–diode voltage multiplier centrally fed from a dc–dc boost converter is used to elevate the input voltage to a proper high-voltage level. Finally, a modular multilevel converter is employed to chop the elevated voltage into unipolar or bipolar pulsed output voltage (based on the user selection). The suggested arrangement provides a high-voltage gain with relatively low-voltage components, i.e., neither high-voltage nor series-connected components are needed in the proposed approach. A comparison between the proposed approach and the other Marx-Based pulse generators has been held to show the merits of the proposed approach. A detailed design of the generator passive components and semiconductor devices has been presented. Simulation and experimental results are presented for the unipolar as well as the bipolar pulsed output to validate the proposed concept. [ABSTRACT FROM AUTHOR]

Repetitive high pulsed electric field (PEF) is an effective method to kill microorganisms and bacteria in water treatment applications. The PEF can be generated by applying high-power electromagnetic pulse across the sample to be treated. There are two main types of high-voltage pulse generators, namely, unipolar and bipolar. In this paper, a full-bridge submodule-based modular high-voltage pulse generator, having the ability to generate unipolar and bipolar high-voltage pulses with different shapes from a relatively low-voltage input dc supply, is proposed. In the proposed configuration, relatively low-voltage insulated gate bipolar transistors (IGBTs) are required to generate the high-voltage bipolar pulses. A thyristor rated at the level of the pulsed output voltage is required in the proposed configuration to bypass the load during the charging process of capacitors. In the proposed approach, a thyristor is used instead of the self-commutated high-voltage switch (e.g., series-connected IGBTs), as thyristors are available with high-voltage ratings and possess inherent reverse voltage blocking capability. A detailed illustration of the proposed configuration and its operational concept are introduced in this paper. Simulation and experimental results are presented to validate the proposed approach. [ABSTRACT FROM AUTHOR]

Modular multilevel converters (MMCs) have become one of the most promising topologies for high-voltage dc–ac conversion. DC-side fault blocking capability of the MMC has prompted significant research in recent years. In this paper, a new switched capacitor submodule (SCSM) for MMCs is proposed which provides operation with DC fault blocking capability. In addition, successful voltage balancing is achieved with half the number of voltage sensors used with existing MMC cells. Generally, conventional sensor-based balancing techniques require a significant amount of measurements, 2m(N-1) voltage sensors, and 2m current sensors for an N-level m-phase MMC. The proposed cell will thus aid in reducing the complexity of the control system. A detailed illustration of the operational concept of the proposed architecture is presented in this paper. A comparison between the proposed SCSM and other existing MMC cells has been included to highlight the benefits of the proposed SCSM. A simulation model for an MMC-based HVDC system along with the proposed cell has been built to test its performance during normal as well as abnormal operating conditions. The simulation results show the effectiveness of the proposed architecture. [ABSTRACT FROM PUBLISHER]

Offshore wind energy is now seen as a key contributor for the future renewable energy mix. HVDC technology is among the chief technologies enabling widespread use of offshore wind. Thanks to their numerous advantages, voltage-source converter-based-HVDC (VSC-HVDC) systems are expected to be the technology of choice. Unfortunately, most of VSCs are defenseless against dc-side faults, such as two-level VSCs, and half-bridge modular multilevel converters. This paper proposes the buck-boost inverter-based-HVDC system (BBI-HVDC) as a means to overcome the limitations of the classical VSC-HVDC systems. The proposed configuration does not only provide sinusoidal three-phase voltage, but also provides complete blocking capability of ac-side contributions during a dc-side fault. The latter is achieved by simply disabling the gating signals to the switches upon fault detection. The performance of the proposed system is illustrated during normal conditions, ac-side faults, and dc-side faults. A simulation case study comparing the performance of the conventional HVDC converters with the proposed system during dc-side faults is conducted. The simulation results reveal the promising performance under normal operation as well as a significant decrease in the dc fault current due to the ac-side contribution blocking capability of the BBI-HVDC system during dc-side faults. [ABSTRACT FROM AUTHOR]