Search

An adaptive virtual-inductance feedforward scheme is presented in this article to enhance the stable operation of smart inverters in weak grids. In the developed scheme, the virtual inductance is updated in real time according to an adaptation law to ensure that the inverter follows the dynamic response of a robust reference model, thereby ensuring stability without the need for any grid impedance estimation. In this article, the developed scheme is validated with experimental results obtained from testing a small-scale two-level, 208-V, 2-kW inverter. [ABSTRACT FROM AUTHOR]

Grid-interactive inverters allow distributed generation units to provide various ancillary services in microgrids. As the linear modulation region of inverters is restricted by the dc-bus voltage, providing ancillary services may drive the fundamental positive-sequence inverter voltage to the overmodulation region. Therefore, to operate in the linear modulation region the maximum active- and reactive-power of the inverter may have to be reduced unless pulsewidth modulation (PWM) references are adjusted. In this paper, an atypical PWM method is proposed for maximizing dc-bus utilization of grid-interactive two-level voltage source inverters (2L-VSI) providing ancillary services. Two important ancillary services, i.e., negative-sequence compensation and harmonic compensation are considered in this paper. The proposed method increases the maximum active- and reactive-power that a 2L-VSI can deliver when providing ancillary services by injecting a common-mode component in the references computed based on instantaneous reference magnitudes. The validity of the proposed technique is verified through simulation, as well as experimental data obtained using a 208-V three phase grid-connected 2L-VSI. [ABSTRACT FROM AUTHOR]

An adaptive sinusoidal pulse-width modulation (SPWM) technique for cascaded H-bridge (CHB) multilevel converters is presented in this paper. The proposed technique enables the CHB topology to provide a symmetrical ac voltage from a set of asymmetrical time-variant input dc-source voltages. A sensor-per-source (SPS) algorithm and a sensor-per-leg (SPL) algorithm are described as alternatives for implementing the adaptive SPWM technique. Software simulations and experimental results are presented to demonstrate the efficacy of the presented SPS and SPL algorithms. [ABSTRACT FROM PUBLISHER]

As the number of renewable energy generation units and, consequently, solid-state based converters increases in the power grid, many power electronics concepts should be integrated into power system analysis and design. Thus, a power laboratory course with emphasis on the nexus between power electronics and power system is desired. However, the flexibility of instructors in designing a wide range of educational experiments is limited by the use of specialized educational setups. This problem can be resolved by allowing students to assemble their setups using laboratory scaled-down devices; however, implementation times can limit students to focus on the main concepts of the experiments. In particular, lacking experience with hardware description languages to develop switching patterns and control schemes for solid-state based converters further increases the implementation times. In this paper, a technique for rapidly implementing switching patterns and control schemes for power converters is proposed. This technique provides an easy-to-use laboratory allowing students to focus on reinforcing the theory learned in energy conversion, motor-drive, power electronics, and power system classes while still providing instructors with the flexibility to design a wide range of educational experiments. [ABSTRACT FROM PUBLISHER]

The phasor-PWM-based current source inverter (CSI) is a boost inverter. The difference between conventional CSIs and the boost inverter is that the boost ratio (VLLrms/Vdc ) in the boost inverter can easily be above 3.0, whereas this ratio is around 1 in conventional CSIs. In order to realize the potential capabilities of the boost inverter and to assist its penetration into renewable energy systems, the boost inverter dynamic behaviors are studied in this paper. First, the large- and small-signal models as well as the dq-equivalent circuits of the boost inverter are presented. Then, the developed models are verified using circuit simulations and experiments on a laboratory-scale 2-kW 208/240- V_{\rm LLrms} V_{\rm dc}=65\ \hbox{V} $ boost inverter made of reverse-blocking IGBTs. Finally, the developed small-signal model is used to study the stability of the boost inverter through root locus of small signal poles (eigenvalues) as control inputs, and load parameters vary within the boost inverter's operating limits. [ABSTRACT FROM PUBLISHER]

Inverters play key roles in motor drives, flexible power transmissions, and recently grid-tied renewable energy generation units. Therefore, availability and reliability of inverters have become increasingly important. Following early stage fault detections in inverters, remedial actions can extend normal operation of inverters and, in some cases, derate the system to prevent unexpected shutdowns. A remedial action typically contains a combination of hardware and software reconfigurations. The main purpose of this paper is to provide an instructive survey of existing fault-tolerance (remedial) techniques for three-phase, two-level, and multilevel inverters. [ABSTRACT FROM PUBLISHER]

A method for the seamless transition of three-phase inverters switched between grid-tied and stand-alone modes of operation is presented in this paper. In this method, only the inverter current and voltage sensors are utilized, and no control over the grid-side static transfer switch is needed. The presented method contains two strategies for grid-tied-to-stand-alone and stand-alone-to-grid-tied transitions. In the stand-alone-to-grid-tied transition strategy, a novel algorithm is presented for estimating the grid angle nearly instantaneously, which allows the three-phase inverter to respond very quickly if the grid and point-of-common-coupling voltages are out of phase. This fast response allows the inverter to effectively eliminate the transient overcurrent that would normally occur if it was connected to the grid without first being synchronized. The fast response also allows the inverter to return to normal operation very quickly after such an event. The strategy for the seamless transition from grid-tied to stand-alone mode is also presented. These strategies have been verified through experiments, and the results are presented in this paper. [ABSTRACT FROM PUBLISHER]

In many modern energy conversion systems, a dc voltage, which is provided from a sustainable energy source or energy storage device, must be boosted and converted to an ac voltage with a fixed amplitude and frequency. In this paper, a switching pattern based on the concept of the conventional space-vector pulsewidth-modulated (SVPWM) technique is developed for single-stage, three-phase boost-inverters using the topology of current-source inverters. The six main switching states, and two zeros, with three switches conducting at any given instant in conventional SVPWM techniques are modified herein into three-charging states and six discharging states with only two switches conducting at any given instant. The charging states are necessary in order to boost the dc input voltage. The developed switching pattern was experimentally verified through a laboratory-scaled three-phase 500-W boost inverter and the results are presented in this paper. [ABSTRACT FROM AUTHOR]