Search

This paper introduces a new cross-correlation anti-islanding detection scheme for module-integrated converters (MICs) with pseudo dc-link. The proposed scheme periodically injects a second-order harmonic current component of low magnitude (in open-loop mode) and evaluates grid response by means of correlation. The proposed scheme is highly reliable, providing nondetection-zone free operation, fast detection, and compliance with the relevant power quality and anti-islanding standards. Additionally, it excels in lower computational cost, reduced fault detection zone, and higher output power quality, compared to the referenced anti-islanding schemes that are compatible with MICs. Last but not least, it can be implemented in MIC platforms without requiring an output current sensor, being an easily upgradable solution in software level. A firm theoretical framework that considers both high penetration levels of PV systems and weak grid conditions is also included in this paper. The theoretical framework, as well as the effectiveness of the proposed scheme, is verified through extensive experimental results for various electrical-network parameters and nonlinear loading conditions. Finally, a comprehensive comparison between the proposed method and the most common anti-islanding techniques (compatible with MICs) is performed, leading to some valuable conclusions from MICs perspective. [ABSTRACT FROM AUTHOR]

This paper studies the significant impact of distributed-energy-resource (DER) inverters (which are connected to the same node) on anti-islanding protection of DER-installations. As it concerns the harmonic injection-based schemes, the induced harmonic voltage component that is provoked by each inverter is compromised, as synchronous injection (injection at the same time intervals) among the inverters cannot be reassured. Therefore, harmonic injection-based anti-islanding schemes will fail if the harmonic voltage component falls below a certain level. In this framework, a novel metric (i.e., the upgrade factor, UF) is introduced, indicating the supplementary power (of DERs) that can be installed in the same point of common coupling without compromising the effectiveness of the harmonic injection scheme. As this metric enables the evaluation of harmonic injection schemes prior to the future integration of DERs, it could be a substantial addendum into the relevant standards that evaluates the anti-islanding features of grid-tied DER-inverters. Finally, this paper proposes a technique (implemented in the software level), which maximizes UF and reassures the effectiveness of the harmonic injection schemes under the power variations of installed inverters. Extensive simulations and experimental tests have been conducted that verify the effectiveness of the proposed strategy under various penetration-levels and islanding-network conditions. [ABSTRACT FROM AUTHOR]

Over recent years, the output power of micro-inverters [module-incorporated inverter (MIC)] is progressively pushed to higher levels, following the current photovoltaic (PV) modules market trends. The interleaved Flyback inverter—under discontinuous conduction mode of operation (DCM)—is an appealing solution for PV applications which are based on MIC technology. This topology provides increased power level for distributed PV generation exploitation with simple control configuration, high efficiency, and reduced filter size. In this paper, the harmonic injection capability is incorporated into the interleaved Flyback inverter for the implementation of an active anti-islanding scheme. A suitable technical solution is proposed that bypasses the unfolding H-bridge, without affecting the active power generation of the inverter and without requiring any hardware modification. In addition, a mathematical model based on the instantaneous power balance theory is presented, being a powerful analysis tool for inverters operating under complete magnetic discharge such as the Flyback inverter (either conventional or interleaved) under DCM or boundary conduction mode of operation. The proposed model predicts accurately the steady-state operational behavior of the Flyback inverter under current harmonic injection, either in grid-tied or islanding operation. The proposed technical implementation method and mathematical model are verified through simulation and experimental results. Finally, an anti-islanding set-up based on the proposed harmonic injection technique is presented and implemented into the Flyback micro-inverter. The proposed set-up is verified through experimental results on various quality factor values, as well as for weak grid conditions. [ABSTRACT FROM AUTHOR]

During the last decade, autonomous residential photovoltaic (PV) systems have been widely installed, especially in remote areas (islands, rural territories, etc.), in an effort to produce electrical energy in a reliable and inexpensive manner. The appropriate design of a PV system and the compatibility of its power quality indices with national and international standards are crucial for efficient and economical autonomous operation of the system. To this direction, the critical parameters of a three-phase autonomous PV residential system are properly determined. Moreover, a new design methodology that meets the demanded standards and improves further the power quality is also introduced. Finally, an optimization algorithm is designed utilizing artificial intelligence techniques. The analytical results are corroborated by extensive simulation results and insightful discussions are provided demonstrating the efficiency of our proposed design. [ABSTRACT FROM PUBLISHER]