Search

The KSTAR current lead system (CLS) was commissioned during the first campaign of the plasma experiments. The current lead system is divided into a toroidal field (TF) system and a poloidal field (PF) system. Two pairs of current leads for the TF system and 7 pairs for the PF system were installed. Instead of the copper leads, vapor-cooled type brass current leads (CLs) were mounted in order to minimize the cryogenic load. The CLs were installed after the verification of the components through helium leak tests, low current charging tests at room temperature, and high voltage tests. The stability of the CLS was inspected through LN2 cool down tests, helium leak tests, flow control tests, and temperature control tests using a ceramic heater after the installation all of their components. During the first campaign, it was cool down until liquid helium temperature after vacuum pumping and the helium flow rates of the CLs were controlled successfully at the optimum values. In case of the TF CLs were 0.20 g/s and 0.26 g/s at zero current and 15 kA respectively. On the other hands the PF CLs kept 0.2 g/s during PF coil operation at 4 kA and zero current. And a ceramic heater was reliably operated to prevent water condensation at the warm terminal of the CL. [ABSTRACT FROM AUTHOR]

The KSTAR superconducting magnetic coils, which are made of cable in-conduit conductor (CICC), maintain a superconducting state with forced-flow supercritical helium (4.5 K, 5.5 bar). During current changing of the superconducting magnetic coils, AC losses are generated in the CICC due to dI/dt, and the heat generated from the loss is removed by high heat capacity supercritical helium. At the same time, reversed flow of the helium occurs due to a rapid increase of the helium temperature and momentary changing of the pressure inside the CICC. This phenomenon has been detected in all of the poloidal field (PF) coils, especially in the upper (U) and lower (L) PF1 ~ PF4 coils. The maximum change of the magnetic field in the PF1UL ~ PF4UL coils is located near the inlet and outlet of the helium cooling channels, and that of the PF5UL ~ 7UL coils is located at the center of the cooling channel. The temperature variation at the helium inlet was always measured to have a time delay after each shot. In the PF1 coil tests, it was measured to have a delay of 26 sec. During the first plasma campaign, this phenomenon was more severe in the case of all PF coils operating together than for a single PF operation. In this paper, we investigated the thermal-hydraulics of this phenomenon. [ABSTRACT FROM AUTHOR]

To protect the KSTAR (Korea Superconducting Tokamak Advanced Research) superconducting coils against a quench, the quench detection system based on voltage measurement was fabricated. It used a detect/dump scheme which detects the presence of non-recovering normal zones and activates a dump circuit that transfers most of the stored energy into a dump resistor. Even though it is desirable to discharge the coil energy as fast as possible after quench detection, a time delay between the quench detection and the complete dump circuit actuation will be necessary in order that the quench voltage is to be distinguished from various noises. The quench threshold voltage and the delay time should be set before operation for quench voltage detection so that the maximum hot-spot temperature could be limited to 150 K. This paper describes the hardware techniques to prevent the malfunction of the quench detection due to voltage noises arising from the KSTAR operating scenarios. During the first operation of the KSTAR machine, the inductive voltages and other voltage noises were measured and effectively compensated below voltage thresholds. A quench did not occur and the quench detection system was well operated without any false activation. [ABSTRACT FROM AUTHOR]

KSTAR (Korea Superconducting Tokamak Advanced Research) superconducting magnet consists of a CICC (Cable-In-Conduit Conductor) and is cooled down less than 5 K using supercritical helium. The length of CICC is 610 m for TF coil and maximum about 2,500 m for PF coil respectively, especially the cooling channel is about maximum 300 m in PF coil because of continuous winding scheme. There are many cooling channels in KSTAR coils especially 84 channels in TF magnet system and 100 channels in PF magnet system. Flow imbalance affects cool down of magnet and leads to a difficulty of flow control. The pressure drop between CICC terminals has a close relationship with CICC hydraulic characteristic, helium refrigerator's performance and efficiency. The friction factor which is a representative parameter can be obtained under cryogenic operation condition. We attempt to find out the friction factor of KSTAR CS and PF CICC according to the test result of KSTAR CSMC (Central Solenoid Model Coil) 2nd campaign and compare the results with previous tests. The hydraulic characteristics of KSTAR superconducting magnet system like mass flow distribution, friction factor in conductor, pressure drop and etc during CSMC test and initial commissioning of KSTAR are presented. We can confirm the KSTAR CICC's unique hydraulic behavior in states of cool down and current charging period. Also, we expect that measured data will help to operate KSTAR and be a reference for thermo-hydraulic simulation. [ABSTRACT FROM AUTHOR]

The KSTAR components requiring cryogenic helium coolant for superconducting magnet operations are connected to the helium refrigeration system (HRS) through the helium distribution system (HDS), the final helium distribution station. Twenty eight cryogenic valves including 4 quench protecting valves, many sensors such as temperature sensors, pressure transmitters, and flowmeters are mounted on the system. The HDS has to control the 4.5 K supercritical helium (600 g/s) for 30 superconducting coils and their superconducting bus-lines, 55 K helium (270 g/s) pressurized to 18 bars for the thermal shields and the gravity supports, and a maximum 17.5 g/s of liquid helium for 18 current leads, provided from the HRS which has a 4.5 K equivalent cooling power of 9kW. The helium distribution system consists of a helium distribution box (DB), 5 helium transfer lines, a PLC based helium control system (HCS), etc. The helium control system is connected to the KSTAR supervisory control & interlock system. The detailed status regarding the construction, commissioning during first cool-down, and the instrumentation & control (I&C) system are included in this paper. [ABSTRACT FROM AUTHOR]

The magnet system comprises sixteen toroidal field (TF) coils and fourteen poloidal field (PF) coils for KSTAR (Korea Superconducting Tokamak Advanced Research) Tokamak. All the TF coils and 10 PF coils (PF1~ 5 UL) are made of Nb3 Sn strands and 4 PF coils (PF6 ~ 7 UL) are made of NbTi strands. Before operating the superconducting coils, it is critical to verify the operation conditions such as thermo-hydraulic parameters and stability boundaries. In this regards, the TF model coil and CSMC (Central Solenoid Model Coil) have been tested and the operating conditions have been analyzed. Before cool down, parameters such as helium flow through conduits, electrical insulation and coil geometry have been measured at room temperature to confirm the manufacturing soundness. During cool down and current charging, thermo-hydraulic and mechanical parameters by using mechanical sensors have been measured. Also measured was the magnetic field strength in various positions of the coil conductor. Measured data have been analyzed and the results have been compared with the model analysis by simulation code. [ABSTRACT FROM AUTHOR]

The Korea Superconducting Tokamak Advanced Research (KSTAR) Central Solenoid Model Coil (CSMC) was tested at the National Fusion Research Center (NFRC) to verify the design and manufacturing engineering and to ensure reliable operation. The CSMC reached 8.6 T at 20 kA DC operation successfully. We also assessed the AC loss of the CSMC by means of both a sinusoidal wave with a DC offset as well as a triangular pulse. We derived a friction factor correlation of CSMC at room temperature and at cryogenic temperature (4 ∼ 6 K). We also investigated the variation of the friction factor during current charging. The KSTAR PF coil simulation code was validated with inlet and outlet helium temperature, mass flow rate, and pressure drop from the experimental results. The operation temperature margin of the CS1 coil of KSTAR was calculated with the revised KSTAR PF coil simulation coil. [ABSTRACT FROM AUTHOR]

The KSTAR Central Solenoid Model Coils (CSMC), which are in the form of split coils with same dimension, have been tested. The CSMC were successfully charged up to 20 kA and down to zero with different ramp rates. Various pulse waveforms were applied to the CSMC to analyse the AC-loss characteristics of the coils. The measurement method was a gas-flow calorimetry. In this work, two types of waveforms, the DC-biased sinusoidal wave (Idc = 2, 4 kA; ΔIac = 1 kA; ƒ = 0.08 ∼ 0.67 Hz) and a single triangular pulse (Imax = 6 ∼ 10 kA; dI/dt = 0.5 ∼ 2 kA/s), are selected and analysed. From the measured data at the one outlet where helium channel 3 and 4 are merged, the AC loss parameters, related with the hysteresis loss and the coupling loss, are calculated. The B-field strength differs depending on the position within the cooling channels. The spatial field variation and the ramp rate were 0.048∼ 1.9T and 8.1∼ 71 mT/s for the DC-biased sinusoidal waves, while 0.29∼ 4.3 T and 0.024∼ 0.86 T/s for the triangular pulses. The measured AC losses are compared with estimated values and the behavior agrees well. The coupling time constant (nτ) varies with the field strength. In case of the triangular pulses, nτ increases by increasing the field amplitude and the maximum value of nτ is 41 ms with Imax = 10 kA. [ABSTRACT FROM AUTHOR]

The KSTAR (Korea Superconducting Tokamak Advanced Research) superconducting magnet system which consists of 16 TF coils and 14 PF coils adopts a superconducting CICC (Cable-In-Conduit Conductor) type conductor. The KSTAR magnet system uses two different types of CICCs--Nb3Sn cable with Incoloy 908 conduit and NbTi cable with 316LN stainless-steel conduit A continuous CICC jacketing system is developed for the KSTAR CICC fabrication and the jacketing system uses the tube-mill process. It consists of forming, welding, sizing and squaring procedures. The welding condition of CICCs and the fabrication process is described. The repair of the CICC is also discussed. [ABSTRACT FROM AUTHOR]