Search

Previous studies have shown that nanometer scale defects can lead to the formation of submicrometer craters, if located in coatings with a relatively small thickness. Due to the small size, such damages are challenging to detect in the online and offline damage detection and may therefore lead to an overestimation of the LIDT for the tested optical component. However, the influence of these nanopits on the optical properties and the impact on the initiation of catastrophic damage was not investigated in detail in the past. In order to study the correlation between nanopits, optical properties and catastrophic damage, samples with an AR-coating were fabricated by means of ion beam sputtering (IBS) and tested for their laser resistance by LIDT raster scans in the nanosecond regime at 355 nm. The generation and morphology changes of the nanopits were monitored for different pulse numbers and in dependence of the starting fluence. In addition to the inspection with an optical microscope in differential interference contrast (DIC) mode as prescribed by ISO 21254, alternative inspection methods, for example, dark field microscopy and scanning electron microscopy (SEM), were used to detect the nanopits. The damage test revealed that nanopits occur rarely in standard AR-coatings and possess only a small relevance for the LIDT. The typical damage morphology observed consisted of micrometer-sized pits which exhibited a stable size over a large fluence range and no growth after repeated irradiation. © COPYRIGHT SPIE. Downloading of the abstract is permitted for personal use only.

Investigating the properties of manufactured polymer optical fibers is essential to determine proper areas of application. Using pulsed laser radiation, especially with respect to laser activity in optical fibers, the maximum acceptable transmittable energy without inducing damage is of particular interest. Therefore, this work is related to laser-induced damage in polymer optical fibers at a wavelength of 532 nm and a pulse duration of 7.3 ns. In particular, the influence of the coupling condition on the transmittable pulse energy and the damage behavior applying an R-on-1 test procedure are analyzed in this study. The obtained results give information about the long-Term behavior and will be used to optimize the manufacturing process. © COPYRIGHT SPIE

In many advanced fields of optical technology, progresses are extremely dependent on reliable characterization procedures employed for quality assessment in volume manufacturing as well as for the optimization of high performance optical components. With the rapid development of laser technology and modern optics, especially optical metrology gained of importance for the quality management in the industrial production environment and also for research in optical components. Besides absorption and scatter losses, the spectral characteristics and laser induced damage thresholds are considered nowadays as common quality factors, which are often indicated in optics catalogues and are considered by the customers for the design of optical systems. As a consequence of this trend, standardization of measurement procedures for the characterization of optical components became a crucial point for the optics industry and for critical applications of optical components in laser systems as well as conventional optical devices. During the last decade, adapted standard measurement techniques have been elaborated and discussed in the Technical Committee ISO/TC 172 of the International Organization for Standardization (ISO) resulting in practical International Standards or Draft Standards for the measurement of optical absorption, scattering, reflectance and laser induced damage thresholds. In this paper, the current state of standardized characterization techniques for optical components is summarized. Selected standards for the measurement of absorption (ISO 11551), scattering (ISO/DIS 13696) and laser induced damage thresholds (ISO/DIS 11254, Parts 1 and 2) will be described and discussed in view of recent trends in laser technology and its applications in semiconductor lithography.

Ultra-short laser applications require high quality dielectric optics. The natural dispersion of light needs to be matched by dielectric components. However such dispersive components are very challenging for the deposition process and are characterized by high field intensities inside the layer stack. Such layers are expected to diminish the possible laser induced damage thresholds (LIDTs) because of their low optical gap value for suitable high refractive index materials. This paper reports about the manufacturing of amorphous nanolaminates to tune the optical gap. Such sequences are substituted into a conventional high reflective mirror to decrease the electric field of binary Tantala layers by 30 % which correlates to an improvement in LIDT of almost 16%. © 2017 SPIE.

An established method for precise determination of optical absorption is the so called laser calorimetry. According to ISO 115511 laser calorimetry is preferred to other photothermal test methods, because of its capability to deliver absolute calibration. Many optical materials have low heat conductivity, which can affect the calibration significantly. The timeand spatial dependent temperature profile in a sample of materials with low heat conductivity requires accurate temperature measurement strategies to determine material-independent and absolutely calibrated absorption values. For thin cylindrical samples, ISO 11551 provides a strategy to compensate heat conductivity effects. The optimal temperature sensor position, where accordingly calibrated measurement results2 can be obtained, is simply based on the symmetric sample geometry. For thick geometries an additional temperature distribution along propagation direction of the heating beam must be considered. The current version of ISO 11551 does not provide a sophisticated solution for this problem, because the heating scheme of a sample is usually unknown. Therefore, a reliable calibration procedure can only be applied to samples of well-known absorption properties of surfaces and bulk material. Utilizing such kind of specifically prepared reference samples in combination with Finite Element Method (FEM) calculations, a general measurement and data evaluation concept based on laser calorimetry is presented, that allows deriving absolutely calibrated absorption measurement results for rectangular sample geometries. © 2017 SPIE.

The present contribution is addressed to an improved method to fabricate dielectric dispersive compensating mirrors (CMs) with an increased laser induced damage threshold (LIDT) by the use of ternary composite layers. Taking advantage of a novel in-situ phase monitor system, it is possible to control the sensitive deposition process more precisely. The study is initiated by a design synthesis, to achieve optimum reflection and GDD values for a conventional high low stack (HL)n. Afterwards the field intensity is analyzed, and layers affected by highest electric field intensities are exchanged by ternary composites of TaxSiyOz. Both designs have similar target specifications whereby one design is using ternary composites and the other one is distinguished by a (HL)n. The first layers of the stack are switched applying in-situ optical broad band monitoring in conjunction with a forward re-optimization algorithm, which also manipulates the layers remaining for deposition at each switching event. To accomplish the demanded GDD-spectra, the last layers are controlled by a novel in-situ white light interferometer operating in the infrared spectral range. Finally the CMs are measured in a 10.000 on 1 procedure according to ISO 21254 applying pulses with a duration of 130 fs at a central wavelength of 775 nm to determine the laser induced damage threshold. © 2016 SPIE. Downloading of the abstract is permitted for personal use only. DFG/EXC/QUEST Volkswagen Stiftung BMBF/13N11558

The scientific background in the field of the laser induced damage processes in optical coatings has been significantly extended during the last decades. Especially for the ultra-short pulse regime a clear correlation between the electronic material parameters and the laser damage threshold could be demonstrated. In the present study, the quantization in nanolaminates is investigated to gain a deeper insight into the behavior of the blue shift of the bandgap in specific coating materials as well as to find approximations for the effective mass of the electrons. The theoretical predictions are correlated to the measurements. © 2016 SPIE. Downloading of the abstract is permitted for personal use only. Ministry for Science and Culture of Lower Saxony Volkswagen Stiftung

In this work tests for determination of ablation thresholds of various ceramic materials for pulsed laser irradiations at wavelengths of 355 nm and 1064 nm in vacuum are presented. For comparison tests with copper and aluminium are also reported. The ablation process was monitored insitu by long-distance microscopy. The morphology of ablation spots was exsitu inspected by scanning electron microscopy. Furthermore, the redeposition of potentially released particles on optics in the vicinity to the target was examined.

Fused silica optics in the Advanced Laser Interferometer Gravitational-Wave Observatory (LIGO) detectors are extremely sensitive to optical scattering and absorption losses induced by both particulate and hydrocarbon contamination. At full power, the optical surfaces are illuminated with up to 200 kW/cm^2. Additionally, the round-trip test mass cavity loss budget is limited to 70 ppm total from all sources. Even low-level contaminants can result in laser damage to optics during the operation the interferometers, and/or the unacceptable reduction of overall detector sensitivity. These risks are mitigated by a two-pronged approach: quantifying contamination sources and the extent of contamination, then reducing sources and cleaning optics in-situ. As a result of these ongoing efforts, we now have a better understanding of what the contamination levels and sources are, and have made significant improvements to methods of controlling contamination, thus protecting the optics from losses and laser damage in the Advanced LIGO Interferometers.