Search

A distribution system was designed and operated by considering unidirectional power flow from a utility source to end-use loads. The large penetrations of distributed generation (DG) into the existing distribution system causes a variety of technical problems, such as frequent tap changing problems of the on-load tap changer (OLTC) transformer, local voltage rise, protection coordination, exceeding short-circuit capacity, and harmonic distortion. In view of voltage regulation, the intermittent fluctuation of the DG output power results in frequent tap changing operations of the OLTC transformer. Thus, many utilities limit the penetration level of DG and are eager to find the reasonable penetration limits of DG in the distribution system. To overcome this technical problem, utilities have developed a new voltage regulation method in the distribution system with a large DG penetration level. In this paper, the impact of DG on the OLTC operations controlled by the line drop compensation (LDC) method is analyzed. In addition, a generalized determination methodology for the DG penetration limits in a distribution substation transformer is proposed. The proposed DG penetration limits could be adopted for a simplified interconnection process in DG interconnection guidelines.

The Load Tap Changing (LTC) transformer and Shunt Capacitor (SC) bank are major devices for voltage and reactive power control in a distribution substation. Thus, the coordination operation of a LTC transformer and a SC bank is required to achieve better voltage and reactive power compensation at a distribution substation in the same time. This paper proposes coordinate control method of LTC transformer and SC bank to achieve better voltage and reactive power compensation and operation times of these two devices in the same time. The mathematical formulations of the proposed coordinate control method are introduced. Sample case studies are shown to verify the effectiveness of the proposed coordinate control method.

The generating systems use Doubly-Fed Induction Generators (DFIGs) to achieve high conversion efficiency and to reduce the installation cost. This paper presents a modeling and Maximum Power Point Tracking (MPPT) control method of DFIG-based variable-speed wind energy conversion system. The generator considered is a wound rotor induction machine whose stator is connected directly to the grid and the rotor is fed through back-to-back Pulse-Width Modulation (PWM) converters. Stator flux-oriented vector control is applied to control the active and reactive current loops independently. The MPPT control method in a Wind Energy Conversion System (WECS) is proposed. The proposed control solution aims at driving the position of the operating point near to optimality. This is a very important aspect to maintain DFIGs efficiently in a variable wind speed. The wind generator is modeled in RSCAD program which is interfaced with the Real Time Digital Simulator (RTDS).

Penetration of distributed generator(DG) to power distribution system can cause malfunction of existing protection schemes. Because grid interconnected DG can contribute fault currents and make bidirectional current flows on the system, fault contributions from DG can cause an interference of protection relay operation. Therefore, over current protection device of the distribution system with DGs need directional protection schemes. In this paper, improved directional protection algorithms are proposed for the distribution system with DG considering their fault characteristics. And than, these directional protection algorithms are tested and validated in various fault conditions. From the simulation results, it can be seen that the proposed directional protection algorithms are practically efficient for the radial distribution system with DG.

As the penetration of distributed generation systems is recently high, there have been metering errors, trips of protective devices in KEPCO distribution systems including an occurrence of false fault-indicator in distribution automation system. The cause of malfunctions was the reverse-power-flow phenomenon due to transformer wiring types. By the effect of the reverse-power-flow, each of phase`s fundamental currents was added by about 3 times on the neutral line. A new method based on the analysis of the reverse-power-flow is proposed in this paper. Fault currents on each section were analyzed by the proposed method, and the effect of types of transformer wiring was examined experimentally. In order to reduce the malfunctions due to the reverse-power-flow, controlling the zero-sequence impedance of transformer was designed and verified by using PSCAD/EMTDC software.

The grid-interconnected Microgrid must be able to operate without the utility's grid to supply electricity in case of outage. To operate in standalone mode, the Microgrid must control electricity demand or supply to maintain the frequency. The Microgrid EMS (Energy Management System) could control supply and demand with the AGC (Auto Generation Control) function using a communication line. Note, however, that the period of AGC is too slow to maintain the frequency if there is rapid variation in loads or generation. Moreover, the transition of operation mode could fail if there is too much power flow at PCC (Point of Common Coupling). In this paper, we propose a method of improving the stability of the grid-interconnected Microgrid using BESS (Battery Energy Storage System) and super capacitor. The cooperative control method between BESS and super capacitor uses droop, which is used at the generator. BESS could operate as UPC (Unit Power Control) or FFC (Feeder Flow Control) depending on Microgrid's operation strategy. We simulate the cooperative control method using PSCAD/EMTDC to verify the validity of the method. As a result, Microgrid's stability is improved using the cooperative control method, and the life span of BESS could be prolonged.