Search

Intensive use of military vehicles in military installations create conditions favorable for gully formation. Gullies impede the access of vehicle, restrict the continuation of training, and lead to significant damage to vehicle and risk the life of soldiers. Therefore, it is critical to correctly identify the locations of gullies for continuous training mission. In this study, Fort Riley (FR) military installation was chosen as the study area. LiDAR derived 1 m resolution digital elevation model (DEM) acquired on 2010 was used to map the gullies. A procedure that measures local topographic position, i.e., difference from mean elevation (DFME) along with its integration to the land surface having high surface curvature values was employed. Two high spatial resolution WorldView-2 images of 2010 and field gully data collected in 2010 were utilized for accuracy assessment. Results showed that: (1) A total of 237 small and 166 large gullies were detected and most of them dominated the central west and northwest parts of the installation; (2) Based on the visual interpretation in the WorldView-2 images, there was no statistically significant difference between the detected and observed numbers of gullies; (3) Gullies measured in the field were well detected with an overall accuracy of 78%. [ABSTRACT FROM AUTHOR]

Forest canopy cover (CC) directly and indirectly influences various processes of forest ecosystems. Airborne light detection and ranging (LiDAR) can be used to characterize forest spatial structures and further obtain estimates of forest CC. However, nonreturn laser pulses from targets of interest impact the estimation accuracy of forest CC. The objective of this article was to develop a novel method of estimating the nonreturn laser pulses to improve the estimation accuracy of forest CC using LiDAR data. The improved models for estimating forest CC were developed by introducing the loss ratio of laser pulses and a CC coefficient into the original models. The forest CC reference data were collected and used to validate the forest CC estimates. The results show that the loss ratio for forested areas was much higher than that for open ground areas. The range between the sensor and a target was a crucial factor that caused the loss of returns. The relationship between the range and the loss ratio was nonlinear in both open ground and forested areas. Compared with the original models, the improved models combining the loss ratio and the CC coefficient statistically significantly increased the estimation accuracy of the forest CC. Moreover, the forest CC estimates from the canopy height model (CHM) were more accurate than those from the height normalized point cloud (NPC) data. In addition, the simplified models were more generalized than the other models. This article is novel and has great potential to improve mapping of forest CC. [ABSTRACT FROM AUTHOR]

Estimating individual tree diameters at breast height (DBH) from delineated crowns and tree heights on the basis of airborne light detection and ranging (LiDAR) data provides a good opportunity for large-scale forest inventory. Generally, ground-based measurements are more accurate, but LiDAR data and derived DBH values can be obtained over larger areas for a relatively smaller cost if a right procedure is developed. A nonlinear least squares (NLS) regression is not an appropriate approach to predict the aboveground biomass (AGB) of individual trees from the estimated DBH because both the response variable and the regressor are subject to measurement errors. In this study, a system of compatible individual tree DBH and AGB error-in-variable models was developed using error-in-variable regression techniques based on both airborne LiDAR and field-measured datasets of individual Picea crassifolia Kom. trees, collected in northwestern China. Two parameter estimation algorithms, i.e., the two-stage error-in-variable model (TSEM) and the nonlinear seemingly unrelated regression (NSUR), were proposed for estimating the parameters in the developed system of compatible individual tree DBH and AGB error-in-variable models. Moreover, two model structures were applied to estimate AGB for comparison purposes: NLS with AGB estimation depending on DBH (NLS&DD) and NLS with AGB estimation not depending on DBH (NLS&NDD). The results showed that both TSEM and NSUR led to almost the same parameter estimates for the developed system. Moreover, the developed system effectively accounted for the inherent correlation between DBH and AGB as well as for the effects of measurement errors in the DBH on the predictions of AGB, whereas NLS&DD and NLS&NDD did not. A leave-one-out cross-validation indicated that the prediction accuracy of the developed system of compatible individual tree DBH and AGB error-in-variable models with NSUR was the highest among those estimated by the four methods evaluated, but, statistically, the accuracy improvement was not significantly different from zero. The main reason might be that, except for the measurement errors, other source errors were ignored in the modeling. This study implies that, overall, the proposed method provides the potential to expand the estimations of both DBH and AGB from individual trees to stands by combining the error-in-variable modeling and LiDAR data and improve their estimation accuracies, but its application needs to be further validated by conducting a systematical uncertainty analysis of various source errors in a future study. [ABSTRACT FROM AUTHOR]

Forest canopy height is one of the most important spatial characteristics for forest resource inventories and forest ecosystem modeling. Light detection and ranging (LiDAR) can be used to accurately detect canopy surface and terrain information from the backscattering signals of laser pulses, while photogrammetry tends to accurately depict the canopy surface envelope. The spatial differences between the canopy surfaces estimated by LiDAR and photogrammetry have not been investigated in depth. Thus, this study aims to assess LiDAR and photogrammetry point clouds and analyze the spatial differences in canopy heights. The study site is located in the Jigongshan National Nature Reserve of Henan Province, Central China. Six data sets, including one LiDAR data set and five photogrammetry data sets captured from an unmanned aerial vehicle (UAV), were used to estimate the forest canopy heights. Three spatial distribution descriptors, namely, the effective cell ratio (ECR), point cloud homogeneity (PCH) and point cloud redundancy (PCR), were developed to assess the LiDAR and photogrammetry point clouds in the grid. The ordinary neighbor (ON) and constrained neighbor (CN) interpolation algorithms were used to fill void cells in digital surface models (DSMs) and canopy height models (CHMs). The CN algorithm could be used to distinguish small and large holes in the CHMs. The optimal spatial resolution was analyzed according to the ECR changes of DSMs or CHMs resulting from the CN algorithms. Large negative and positive variations were observed between the LiDAR and photogrammetry canopy heights. The stratified mean difference in canopy heights increased gradually from negative to positive when the canopy heights were greater than 3 m, which means that photogrammetry tends to overestimate low canopy heights and underestimate high canopy heights. The CN interpolation algorithm achieved smaller relative root mean square errors than the ON interpolation algorithm. This article provides an operational method for the spatial assessment of point clouds and suggests that the variations between LiDAR and photogrammetry CHMs should be considered when modeling forest parameters. [ABSTRACT FROM AUTHOR]

The forest growth and yield models, which are used as important decision-support tools in forest management, are commonly based on the individual tree characteristics, such as diameter at breast height (DBH), crown ratio, and height to crown base (HCB). Taking direct measurements for DBH and HCB through the ground-based methods is cumbersome and costly. The indirect method of getting such information is possible from remote sensing databases, which can be used to build DBH and HCB prediction models. The DBH and HCB of the same trees are significantly correlated, and so their inherent correlations need to be appropriately accounted for in the DBH and HCB models. However, all the existing DBH and HCB models, including models based on light detection and ranging (LiDAR) have ignored such correlations and thus failed to account for the compatibility of DBH and HCB estimates, in addition to disregarding measurement errors. To address these problems, we developed a compatible simultaneous equation system of DBH and HCB error-in-variable (EIV) models using LiDAR-derived data and ground-measurements for 510 Picea crassifolia Kom trees in northwest China. Four versatile algorithms, such as nonlinear seemingly unrelated regression (NSUR), two-stage least square (2SLS) regression, three-stage least square (3SLS) regression, and full information maximum likelihood (FIML) were evaluated for their estimating efficiencies and precisions for a simultaneous equation system of DBH and HCB EIV models. In addition, two other model structures, namely, nonlinear least squares with HCB estimation not based on the DBH (NLS and NBD) and nonlinear least squares with HCB estimation based on the DBH (NLS and BD) were also developed, and their fitting precisions with a simultaneous equation system compared. The leave-one-out cross-validation method was applied to evaluate all estimating algorithms and their resulting models. We found that only the simultaneous equation system could illustrate the effect of errors associated with the regressors on the response variables (DBH and HCB) and guaranteed the compatibility between the DBH and HCB models at an individual level. In addition, such an established system also effectively accounted for the inherent correlations between DBH with HCB. However, both the NLS and BD model and the NLS and NBD model did not show these properties. The precision of a simultaneous equation system developed using NSUR appeared the best among all the evaluated algorithms. Our equation system does not require the stand-level information as input, but it does require the information of tree height, crown width, and crown projection area, all of which can be readily derived from LiDAR imagery using the delineation algorithms and ground-based DBH measurements. Our results indicate that NSUR is a more reliable and quicker algorithm for developing DBH and HCB models using large scale LiDAR-based datasets. The novelty of this study is that the compatibility problem of the DBH model and the HCB EIV model was properly addressed, and the potential algorithms were compared to choose the most suitable one (NSUR). The presented method and algorithm will be useful for establishing similar compatible equation systems of tree DBH and HCB EIV models for other tree species. [ABSTRACT FROM AUTHOR]

Rapidly advancing airborne laser scanning technology has become greatly useful to estimate tree- and stand-level variables at a large scale using high spatial resolution data. Compared with that of ground measurements, the accuracy of the inferred information of diameter at breast height (DBH) from a remotely sensed database and the models developed with traditional regression approaches (e.g., ordinary least square regression) may not be sufficient. Thus, this regression approach is no longer appropriate to develop accurate models and predict DBH from remotely sensed-related variables because DBH is subject to the random effects of forest stands. This study developed a generalized nonlinear mixed-effects DBH estimation model from remotely sensed imagery data. The light detection and ranging (LiDAR)-derived stand canopy density, crown projection area, and tree height were used as predictors in the DBH estimation model. These variables can be more readily measured over an extensive forest area with higher accuracy compared to the conventional field-based methods. The airborne LiDAR data for a total of 402 Picea crassifolia Kom trees on a sample plot that were divided into 16 sub-sample plots and located in the most important distribution region of western China were used. The leave-one sub-sample plot-out cross-validation method was applied to evaluate the model's prediction accuracy. The results indicated that the random effects of the sub-sample plot on the prediction of DBH were large and their inclusion into the DBH model significantly improved the prediction accuracy. The prediction accuracy of the proposed model at the mean (M) response was also substantially improved relative to the accuracy obtained from the base model. Among several tree selection alternatives evaluated, a sample size of the two largest trees per sub-sample plot used in estimating the random effects showed a significantly higher accuracy compared to other sampling alternatives. This sample size would balance both the measurement cost and potential prediction errors. The nonlinear mixed-effects DBH estimation model at the M response can also be applied if obtaining the estimates of individual tree DBH with a relatively lower cost, and a lower prediction accuracy was the purpose of the study. [ABSTRACT FROM AUTHOR]

Conventional ground survey data are very accurate, but expensive. Airborne lidar data can reduce the costs and effort required to conduct large-scale forest surveys. It is critical to improve biomass estimation and evaluate carbon stock when we use lidar data. Bayesian methods integrate prior information about unknown parameters, reduce the parameter estimation uncertainty, and improve model performance. This study focused on predicting the independent tree aboveground biomass (AGB) with a hierarchical Bayesian model using airborne LIDAR data and comparing the hierarchical Bayesian model with classical methods (nonlinear mixed effect model, NLME). Firstly, we chose the best diameter at breast height (DBH) model from several widely used models through a hierarchical Bayesian method. Secondly, we used the DBH predictions together with the tree height (LH) and canopy projection area (CPA) derived by airborne lidar as independent variables to develop the AGB model through a hierarchical Bayesian method with parameter priors from the NLME method. We then compared the hierarchical Bayesian method with the NLME method. The results showed that the two methods performed similarly when pooling the data, while for small sample sizes, the Bayesian method was much better than the classical method. The results of this study imply that the Bayesian method has the potential to improve the estimations of both DBH and AGB using LIDAR data, which reduces costs compared with conventional measurements. [ABSTRACT FROM AUTHOR]