Search

The human ankle produces a large burst of 'push-off' mechanical power late in the stance phase of walking, reduction of which leads to considerably poorer energy economy. It is, however, uncertain whether the energetic penalty results from poorer efficiency when the other leg joints substitute for the ankle's push-off work, or from a higher overall demand for work due to some fundamental feature of push-off. Here, we show that greater metabolic energy expenditure is indeed explained by a greater demand for work. This is predicted by a simple model of walking on pendulum-like legs, because proper push-off reduces collision losses from the leading leg. We tested this by experimentally restricting ankle push-off bilaterally in healthy adults (N=8) walking on a treadmill at 1.4 m s-1, using ankle-foot orthoses with steel cables limiting motion. These produced up to (~50% reduction in ankle push off power and work, resulting in up to ~50%greater net metabolic power expenditure to walk at the same speed. For each 1 J reduction in ankle work, we observed 0.6 J more dissipative collision work by the other leg, 1.3 J more positive work from the leg joints overall, and 3.94 J more metabolic energy expended. Loss of ankle push-off required more positive work elsewhere to maintain walking speed; this additional work was performed by the knee, apparently at reasonably high efficiency. Ankle push-off may contribute to walking economy by reducing dissipative collision losses and thus overall work demand. [ABSTRACT FROM AUTHOR]

Muscle–tendon power output is commonly assessed in the laboratory through the work loop, a paired analysis of muscle force and length during a cyclic task. Work-loop analysis of muscle–tendon function in out-of-lab conditions has been elusive due to methodological limitations. In this work, we combined kinetic and kinematic measures from shear wave tensiometry and inertial measurement units, respectively, to establish a wearable system for estimating work and power output from the soleus and gastrocnemius muscles during outdoor locomotion. Across 11 healthy young adults, we amassed 4777 strides of walking on slopes from −10° to +10°. Results showed that soleus work scales with incline, while gastrocnemius work is relatively insensitive to incline. These findings agree with previous results from laboratory-based studies while expanding technological capabilities by enabling wearable analysis of muscle–tendon kinetics. Applying this system in additional settings and activities could improve biomechanical knowledge and evaluation of protocols in scenarios such as rehabilitation, device design, athletics, and military training. [ABSTRACT FROM AUTHOR]

During human walking, the center of pressure under the foot progresses forward smoothly during each step, creating a wheeMike motion between the leg and the ground. This rolling motion might appear to aid walking economy, but the mechanisms that may lead to such a benefit are unclear, as the leg is not literally a wheel. We propose that there is indeed a benefit, but less from rolling than from smoother transitions between pendulum-like stance legs. The velocity of the body center of mass (COM) must be redirected in that transition, and a longer foot reduces the work required for the redirection. Here we develop a dynamic walking model that predicts different effects from altering foot length as opposed to foot radius, and test it by attaching rigid, arc-like foot bottoms to humans walking with fixed ankles. The model suggests that smooth rolling is relatively insensitive to arc radius, whereas work for the step-to-step transition decreases approximately quadratically with foot length. We measured the separate effects of arc-foot length and radius on COM velocity fluctuations, work performed by the legs and metabolic cost. Experimental data (A/=8) show that foot length indeed has much greater effect on both the mechanical work of the step-to-step transition (23% variation, P=0.04) and the overall energetic cost of walking (6%, P=0.03) than foot radius (no significant effect, P>0.05). We found the minimum metabolic energy cost for an arc foot length of approximately 29% of leg length, roughly comparable to human foot length. Our results suggest that the foot's apparently wheel-like action derives less benefit from rolling per se than from reduced work to redirect the body COM. [ABSTRACT FROM AUTHOR]

Simple dynamic walking models based on the inverted pendulum predict that the human body's center of mass (COM) moves along an arc during each step, with substantial work performed to redirect the COM velocity in the step-to-step transition between arcs. But humans do not keep the stance leg perfectly straight and need not redirect their COM velocity precisely as predicted. We therefore tested a pendulum-based model against a wide range of human walking data. We examined COM velocity and work data from normal human subjects (N=10) walking at 24 combinations of speed (0.75 to 2.0 m s-1) and step length. These were compared against model predictions for the angular redirection of COM velocity and the work performed on the COM during redirection. We found that the COM is redirected through angular changes increasing approximately linearly with step length (R2=0.68), with COM work increasing with the squared product of walking speed and step length (R2=0.82), roughly in accordance with a simple dynamic walking model. This model cannot, however, predict the duration of COM redirection, which we quantified with two empirical measures, one based on angular COM redirection and the other on work. Both indicate that the step-to-step transition begins before and ends after double support and lasts about twice as long - approximately 20-27% of a stride. Although a rigid leg model can predict trends in COM velocity and work, the non-rigid human leg performs the step-to-step transition over a duration considerably exceeding that of double support. [ABSTRACT FROM AUTHOR]

The plantigrade human foot rolls over the ground during each walking step, roughly analogous to a wheel. The center of pressure progresses on the ground like a wheel of radius 0.3 L (leg length). We examined the effect of varying foot curvature on the mechanics and energetics of walking. We controlled curvature by attaching rigid arc shapes of various radii to the bottoms of rigid boots restricting ankle motion. We measured mechanical work performed on the center of mass (COM), and net metabolic rate, in human subjects (N=10) walking with seven arc radii from 0.02-0.40 m. Simple models of dynamic walking predict that redirection of COM velocity requires step-to-step transition work, decreasing quadratically with arc radius. Metabolic cost would be expected to change in proportion to mechanical work. We measured the average rate of negative work performed on the COM, and found that it followed the trend well (r²=0.95), with 2.37 times as much work for small radii as for large. Net metabolic rate (subtracting quiet standing) also decreased with increasing arc radius to a minimum at 0.3 L, with a slight increase thereafter. Maximum net metabolic rate was 6.25 W kg-1 (for small-radius arc feet), about 59% greater than the minimum rate of 3.93 W kg-1, which in turn was about 45% greater than the rate in normal walking. Metabolic rate was fit reasonably well (r²=0.86) by a quadratic curve, but exceeded that expected from COM work for extreme arc sizes. Other factors appear to increase metabolic cost for walking on very small and very large arc feet. These factors may include effort expended to stabilize the joints (especially the knee) or to maintain balance. Rolling feet with curvature 0.3 L appear energetically advantageous for plantigrade walking, partially due to decreased work for step-to-step transitions. [ABSTRACT FROM AUTHOR]

Purpose: Understanding muscle-tendon forces (e.g., triceps surae and Achilles tendon) during locomotion may aid in the assessment of human performance, injury risk, and rehabilitation progress. Shear wave tensiometry is a noninvasive technique for assessing in vivo tendon forces that has been recently adapted to a wearable technology. However, previous laboratory-based and outdoor tensiometry studies have not evaluated running. This study was undertaken to assess the capacity for shear wave tensiometry to produce valid measures of Achilles tendon loading during running at a range of speeds. Methods: Participants walked (1.34 m⋅s-1) and ran (2.68, 3.35, and 4.47 m⋅s-1) on an instrumented treadmill while shear wave tensiometers recorded Achilles tendon wave speeds simultaneously with whole-body kinematic and ground reaction force data. A simple isometric task allowed for the participant-specific conversion of Achilles tendon wave speeds to forces. Achilles tendon forces were compared with ankle torque measures obtained independently via inverse dynamics analyses. Differences in Achilles tendon wave speed, Achilles tendon force, and ankle torque across walking and running speeds were analyzed with linear mixed-effects models. Results: Achilles tendon wave speed,Achilles tendon force, and ankle torque exhibited similar temporal patterns across the stance phase of walking and running. Significant monotonic increases in peak Achilles tendon wave speed (56.0-83.8 m⋅s-1), Achilles tendon force (44.0-98.7 N⋅kg-1), and ankle torque (1.72-3.68 N⋅m⋅(kg-1)) were observed with increasing locomotion speed (1.34-4.47 m⋅s-1). Tensiometry estimates of peak Achilles tendon force during running (8.2-10.1 body weights) were within the range of those estimated previously via indirect methods. Conclusions: These results set the stage for using tensiometry to evaluate Achilles tendon loading during unobstructed athletic movements, such as running, performed in the field. [ABSTRACT FROM AUTHOR]

This study introduces a noninvasive wearable system for investigating tendon loading patterns during outdoor locomotion on variable terrain. The system leverages shear wave tensiometry, which is a new approach for assessing tendon load by tracking wave speed within the tissue. Our wearable tensiometry system uses a battery-operated piezoelectric actuator to induce micron-scale shear waves in a tendon. A data logger monitors wave propagation by recording from two miniature accelerometers mounted on the skin above the tendon. Wave speed is determined from the wave travel time between accelerometers. The wearable system was used to record Achilles tendon wave speed at 100 Hz during 1-km outdoor walking trials in nine young adults. Inertial measurement units (IMUs) simultaneously monitored participant position, walking speed, and ground incline. An analysis of 5108 walking strides revealed the coupled biomechanical effects of terrain slope and walking speed on tendon loading. Uphill slopes increased the tendon wave speed during push-off, whereas downhill slopes increased tendon wave speeds during early stance braking. Walking speed significantly modulated peak tendon wave speed on uphill slopes but had less influence on downhill slopes. Walking speed consistently induced greater early stance wave speeds for all slopes. These observations demonstrate that wearable shear wave tensiometry holds promise for evaluating tendon tissue kinetics in natural environments and uncontrolled movements. There are numerous practical applications of wearable tensiometry spanning orthopedics, athletics, rehabilitation, and ergonomics. [ABSTRACT FROM AUTHOR]