Search

This study reports for the first time the use of water soluble sulfonated octa-phenyl POSS nanowhiskers for the surface treatment for carbon fibres using simple dip-coating method. The water soluble nature of the functionalized POSS makes it appealing from a formulation perspective as it can be applied simply using an aqueous media. The synthesis of the water soluble SOP-POSS was achieved via one-step aromatic electrophilic sulfonation of octaphenyl POSS. Collective results from NMR, XPS and FTIR analysis confirmed the meta mono-substitution of all phenyl rings in the starting material with a sulfonic group, leading to its water solubility. Surface treatment of commercially oxidized and unsized carbon fibres was achieved via simple dip-coating of the fibres in an aqueous media solution containing the synthesized SOP-POSS product. After the dip-coating process, the carbon fibres are homogeneously covered with surface adsorbed SOP-POSS nanowhiskers. Physico-chemical characterization of the fibres investigated by Inverse Gas Chromatography (IGC) revealed an improvement in surface chemical homogeneity associated with a significant increase in surface oxygen contents and an overall level of surface polarity comparable to commercially sized fibres. The interfacial adhesion properties between the treated carbon fibres and an epoxy matrix were investigated by single fibre fragmentation technique. The results of the tests revealed that significant enhancement of interfacial properties was achieved as a result of a combination of physical inter-molecular interactions at the fibre-matrix interface and localized nano-mechanical strengthening of the epoxy. The outcomes of this research lay the path forward for a potential simple surface treatment of commercial carbon fibres for Interfacial property improvement in composites.

In this work, an atmospheric pressure glow discharge helium plasma treatment was employed to modify the surface properties of jute fibres. The resulting bio-composites showed an increase in flexural properties and interlaminar shear strength (ILSS) compared to composites produced using untreated jute fibres. To understand the reason behind the ILSS improvement, the acid–base properties of jute fibres were determined by contact angle analysis using the capillary rise method. The results were fitted further to van Oss–Chaudhury–Good (vOCG) and Chang–Qin–Chen (CQC) models to determine the Lifshitz–van der Waals (LW) and acid–base components of surface energy. Surface energy determined by the vOCG model revealed that plasma treatment of jute fibre resulted in a 22% increase in total surface energy, a 19% increase in the LW component and a 24% increase in the acid–base component of surface energy. The increase in the acid–base component is due to the significant increase (69%) in the electron-accepting (γ + S)...

This work has focused on measuring the adhesion forces on both untreated and atmospheric helium plasma treated single jute fibre surfaces using scanning probe microscopy (SPM). The measurements were conducted on three differently aged surfaces for one week, three weeks and six weeks using a standard silicon nitride tip in force-volume (f-v) mode. Up to 256 adhesion data points were collected from various locations on the surface of the studied fibres using in-house developed software and the resulting data were statistically analysed by the histogram method. Results obtained from this analysis method were found to be very consistent with a small statistical variation. The work of adhesion, W a, was calculated from measured adhesion force using the Johnson–Kendall–Roberts (JKR) and Derjaguin–Muller–Toporov (DMT) models. Increases in both adhesion force and work of adhesion were observed on jute fibre with certain levels of atmospheric plasma treatment and ageing time.

This work investigates the mechanisms involved in the improvement of flexural properties of a jute/polyester composite when the reinforcement material has been atmospherically plasma treated using helium gas. All composites were laid-up by hand and cured using a Quickstep™ cure cycle. Surface characterization techniques including scanning probe microscopy (SPM), and surface wettability combined with fabric tensile strength, composite flexural strength and composite Mode-I properties have been used to quantify the effects of plasma modification. Flexural strength and modulus increased with plasma treatment time, reaching a maximum at 25 passes before decreasing. SPM topographical analysis showed that roughness of the fibre decreased as the plasma treatment time increased until 25 passes after which the roughness was found to increase again. The coefficient of friction increased rapidly after only a short plasma treatment time (5 passes) whilst wettability continued to increase until 25 passes after which i...