Search

Abstract The application of polymers in medicine requires sterilization while retaining material structure and properties. This demands detailed analysis, which we show exemplarily for the sterilization of PLLA/PDLA core–shell nanofibers with ethylene oxide (EtO). The electrospun patch was exposed to EtO gas (6 vol% in CO2, 1.7 bar) for 3 h at 45 °C and 75% rel. humidity, followed by degassing under pressure/vacuum cycles for 12 h. GC–MS analysis showed that no residual EtO was retained. Fiber diameters (~ 520 ± 130 nm) of the patches remained constant as observed by electron microscopy. Young’s modulus slightly increased and the elongation at break slightly decreased, determined at 37 °C. No changes were detected in 1H-NMR spectra, in molar mass distribution (GPC) or in crystallinity measured for annealed samples with comparable thermal history (Wide Angle X-Ray Scattering). Altogether, EtO emerged as suitable sterilization method for polylactide nanofibers with core–shell morphology. Graphic abstract

High crystallization rate and thermomechanical stability make polylactide stereocomplexes effective nanosized physical netpoints. Here, we address the need for soft, form-stable degradable elastomers for medical applications by designing such blends from (co)polyesters, whose mechanical properties are ruled by their nanodimensional architecture and which are applied as single components in implants. By careful controlling of the copolymer composition and sequence structure of poly[(L-lactide)-co-(ε-caprolactone)], it is possible to prepare hyperelastic polymer blends formed through stereocomplexation by adding poly(D-lactide) (PDLA). Low glass transition temperature Tg ≤ 0 °C of the mixed amorphous phase contributes to the low Young’s modulus E. The formation of stereocomplexes is shown in DSC by melting transitions Tm &gt, 190 °C and in WAXS by distinct scattering maxima at 2θ = 12° and 21°. Tensile testing demonstrated that the blends are soft (E = 12–80 MPa) and show an excellent hyperelastic recovery Rrec = 66–85% while having high elongation at break εb up to &gt, 1000%. These properties of the blends are attained only when the copolymer has 56–62 wt% lactide content, a weight average molar mass &gt, 140 kg·mol−1, and number average lactide sequence length ≥4.8, while the blend is formed with a content of 5–10 wt% of PDLA. The devised strategy to identify a suitable copolymer for stereocomplexation and blend formation is transferable to further polymer systems and will support the development of thermoplastic elastomers suitable for medical applications.

Graphic abstract In vitro thrombogenicity test systems require co-cultivation of endothelial cells and platelets under blood flow-like conditions. Here, a commercially available perfusion system is explored using plasma-treated cyclic olefin copolymer (COC) as a substrate for the endothelial cell layer. COC was characterized prior to endothelialization and co-cultivation with platelets under static or flow conditions. COC exhibits a low roughness and a moderate hydrophilicity. Flow promoted endothelial cell growth and prevented platelet adherence. These findings show the suitability of COC as substrate and the importance of blood flow-like conditions for the assessment of the thrombogenic risk of drugs or cardiovascular implant materials. Supplementary Information The online version contains supplementary material available at 10.1557/s43579-021-00072-6.

Sustainable multifunctional alternatives to fossil-derived materials, which can be functionalized and are degradable, can be envisioned by combining naturally derived starting materials with an established polymer design concept. Modularity and chemical flexibility of polyester urethanes (PEU) enable the combination of segments bearing functionalizable moieties and the tailoring of the mechanical and thermal properties. In this work, a PEU multiblock structure was synthesized from naturally derived L-lysine diisocyanate ethyl ester (LDI), poly(L-lactide) diol (PLLA) and N-(2,3-dihydroxypropyl)-maleimide (MID) in a one-step reaction. A maleimide side-chain (MID) provided a reactive site for the catalyst-free coupling of thiols shown for L-cysteine with a yield of 94%. Physical cross-links were generated by blending the PEU with poly(D-lactide) (PDLA), upon which the PLLA segments of the PEU and the PDLA formed stereocomplexes. Stereocomplexation occurred spontaneously during solution casting and was investigated with WAXS and DSC. Stereocomplex crystallites were observed in the blends, while isotactic PLA crystallization was not observed. The presented material platform with tailorable mechanical properties by blending is of specific interest for engineering biointerfaces of implants or carrier systems for bioactive molecules.

Defined chemical reactions in a physiological environment are a prerequisite for the in situ synthesis of implant materials potentially serving as matrix for drug delivery systems, tissue fillers or surgical glues. ‘Click’ reactions like thiol Michael-type reactions have been successfully employed as bioorthogonal reaction. However, due to the individual stereo-electronic and physical properties of specific substrates, an exact understanding their chemical reactivity is required if they are to be used for in-situ biomaterial synthesis. The chiral (S)-2-mercapto-carboxylic acid analogues of L-phenylalanine (SH-Phe) and L-leucine (SH-Leu) which are subunits of certain collagenase sensitive synthetic peptides, were explored for their potential for in-situ biomaterial formation via the thiol Michael-type reaction. In model reactions were investigated the kinetics, the specificity and influence of stereochemistry of this reaction. We could show that only reactions involving SH-Leu yielded the expected thiol-Michael product. The inability of SH-Phe to react was attributed to the steric hindrance of the bulky phenyl group. In aqueous media, successful reaction using SH-Leu is thought to proceed via the sodium salt formed in-situ by the addition of NaOH solution, which was intented to aid the solubility of the mercapto-acid in water. Fast reaction rates and complete acrylate/maleimide conversion were only realized at pH 7.2 or higher suggesting the possible use of SH-Leu under physiological conditions for thiol Michael-type reactions. This method of in-situ formed alkali salts could be used as a fast approach to screen mercapto-acids for thio Michael-type reactions without the synthesis of their corresponding esters.

The tissue integration of synthetic polymers can be promoted by displaying RGD peptides at the biointerface with the objective of enhancing colonization of the material by endogenous cells. A firm but flexible attachment of the peptide to the polymer matrix, still allowing interaction with receptors, is therefore of interest. Here, the covalent coupling of flexible physical anchor groups, allowing for temporary immobilization on polymeric surfaces via hydrophobic or dipole–dipole interactions, to a RGD peptide was investigated. For this purpose, a stearate or an oligo(ethylene glycol) (OEG) was attached to GRGDS in 51–69% yield. The obtained RGD linker constructs were characterized by NMR, IR and MALDI-ToF mass spectrometry, revealing that the commercially available OEG and stearate linkers are in fact mixtures of similar compounds. The RGD linker constructs were co-electrospun with poly(p-dioxanone) (PPDO). After electrospinning, nitrogen could be detected on the surface of the PPDO fibers by X-ray photoelectron spectroscopy. The nitrogen content exceeded the calculated value for the homogeneous material mixture suggesting a pronounced presentation of the peptide on the fiber surface. Increasing amounts of RGD linker constructs in the electrospinning solution did not lead to a detection of an increased amount of peptide on the scaffold surface, suggesting inhomogeneous distribution of the peptide on the PPDO fiber surface. Human adipose-derived stem cells cultured on the patches showed similar viability as when cultured on PPDO containing pristine RGD. The fully characterized RGD linker constructs could serve as valuable tools for the further development of tissue-integrating polymeric scaffolds. Copyright © 2016 John Wiley & Sons, Ltd.

Polymer degradation occurs under physiological conditions in vitro and in vivo, especially when bonds susceptible to hydrolysis are present in the polymer. Understanding of the degradation mechanism, changes of material properties over time, and overall rate of degradation is a necessary prerequisite for the knowledge-based design of polymers with applications in biomedicine. Here, hydrolytic degradation studies of gelatin-based networks synthesized by copper-catalyzed azide-alkyne cycloaddition reaction are reported, which were performed with or without addition of an enzyme. In all cases, networks with a stilbene as crosslinker proofed to be more resistant to degradation than when an octyl diazide was used. Without addition of an enzyme, the rate of degradation was ruled by the crosslinking density of the network and proceeded via a bulk degradation mechanism. Addition of Clostridium histolyticum collagenase resulted in a much enhanced rate of degradation, which furthermore occurred via surface erosion. The mesh size of the hydrogels (>7 nm) was in all cases larger than the hydrodynamic radius of the enzyme (4.5 nm) so that even in very hydrophilic networks with large mesh size enzymes may be used to induce a fast surface degradation mechanism. This observation is of general interest when designing hydrogels to be applied in the presence of enzymes, as the degradation mechanism and material performance are closely interlinked. Copyright © 2016 John Wiley & Sons, Ltd.

Gelatin-based hydrogels offer various biochemical cues that support encapsulated cells and are therefore suitable as cell delivery vehicles in regenerative medicine. However, besides the biochemical signals, biomechanical cues are crucial to ensure an optimal support of encapsulated cells. Hence, we aimed to correlate the cellular response of encapsulated cells to macroscopic and microscopic elastic properties of glycidylmethacrylate (GMA)-functionalized gelatin-based hydrogels. To ensure that different observations in cellular behavior could be attributed to differences in elastic properties, an identical concentration as well as degree of functionalization of biopolymers was utilized to form covalently crosslinked hydrogels. Elastic properties were merely altered by varying the average gelatin-chain length. Hydrogels exhibited an increased degree of swelling and a decreased bulk elastic modulus G′ with prolonged autoclaving of the starting solution. This was accompanied by an increase of hydrogel mesh size and thus by a reduction of crosslinking density. Tougher hydrogels retained the largest amount of cells; however, they also interfered with cell viability. Softer gels contained a lower cell density, but supported cell elongation and viability. Observed differences could be partially attributed to differences in bulk properties, as high crosslinking densities interfere with diffusion and cell spreading and thus can impede cell viability. Interestingly, a microscopic elastic modulus in the range of native soft tissue supported cell viability and elongation best while ensuring a good cell entrapment. In conclusion, gelatin-based hydrogels providing a soft tissue-like microenvironment represent adequate cell delivery vehicles for tissue engineering approaches. Copyright © 2016 John Wiley & Sons, Ltd.

Strategies to surface‐functionalize scaffolds by covalent binding of biologically active compounds are of fundamental interest to control the interactions between scaffolds and biomolecules or cells. Poly(para‐dioxanone) (PPDO) is a clinically established polymer that has shown potential as temporary implant, eg, for the reconstruction of the inferior vena cava, as a nonwoven fiber mesh. However, PPDO lacks suitable chemical groups for covalent functionalization. Furthermore, PPDO is highly sensitive to hydrolysis, reflected by short in vivo half‐life times and degradation during storage. Establishing a method for covalent functionalization without degradation of this hydrolyzable polymer is therefore important to enable the surface tailoring for tissue engineering applications. It was hypothesized that treatment of PPDO with an N‐hydroxysuccinimide ester group bearing perfluorophenyl azide (PFPA) under UV irradiation would allow efficient surface functionalization of the scaffold. X‐ray photoelectron spectroscopy and attenuated total reflectance Fourier‐transformed infrared spectroscopy investigation revealed the successful binding, while a gel permeation chromatography study showed that degradation did not occur under these conditions. Coupling of a rhodamine dye to the N‐hydroxysuccinimide esters on the surface of a PFPA‐functionalized scaffold via its amine linker showed a homogenous staining of the PPDO in laser confocal microscopy. The PFPA method is therefore applicable even to the surface functionalization of hydrolytically labile polymers, and it was demonstrated that PFPA chemistry may serve as a versatile tool for the (bio‐)functionalization of PPDO scaffolds.

Triggering the release of cargo from a polymer network by ultrasonication as an external, non-invasive stimulus can be an interesting concept for on-demand release. Here, it is shown that, in pH-and thermosensitive microgels, the ultrasound sensitivity of the polymer network depends on the external conditions. Crosslinked poly[(N-isopropylacrylamide)-co-(vinyl imidazole)] microgels showed a volume phase transition temperature (VPTT) of 25-50 degrees C, which increases with decreasing pH. Above the VPTT the polymer chains are collapsed, while below VPTT they are extended. Only in the case of maximum observed swelling, where the polymer chains are expanded, the microgels are mechanically fragmented through ultrasonication. In contrast, when the polymer chains are partially collapsed it is not possible to manipulate the microgels by ultrasound. Additionally, the ultrasound-induced on-demand release of wheat germ lipase from the microgels could be demonstrated successfully. The principle of conditional ultrasound sensitivity is likely to be general and can be used for selection of matrix-cargo combinations.

Functionalization of gelatin with desaminotyrosine (DAT) and desamino tyrosyl tyrosine (DATT) has been demonstrated to allow network formation based on non-covalent interactions of the aromatic moieties. Based on the observation that the DAT(T) groups furthermore could interact with hydroxyapatite fillers, here it was investigated whether such interactions of DAT(T) could also be employed to stabilize composites formed by functionalized gelatins and bioactive glass (BG) particles. Because of sedimentation of the BG microparticles during the gelification, anisotropic composites with two distinct layers were formed. The characterization of mechanical properties by tensile tests and rheology showed that all composites of non-functionalized and DAT(T) functionalized gelatins with BG microparticles showed an increased Young’s modulus (E) up to 3 MPa, an increased storage modulus (G’) up to 100 kPa, increased tensile strength (σmax) up to 3.4 MPa, and increased loss modulus (G’’) compared to the pure matrices. As the observed effects were more pronounced in the DAT(T) functionalized gelatins compared to non-functionalized gelatins, and a much increased thermal stability of these composites was found, it is likely that there are binding interactions between the aromatic moieties and the BG microparticles. This effect open opportunities for the further development of this type of gelatin-based composites for bone regeneration applications.

Gelatin functionalized with glycidyl methacrylate (GMA) has been shown to allow crosslinking by photopolymerization and metathesis reaction. However, side chain functionalization of gelatin might reduce triple helicalization, which influences mechanical properties of gelatin-based polymer networks. Here, the influence of glycidylmethycrylation of gelatin on the chain organization, swelling, and mechanical properties is investigated by comparing among each other physical gels prepared from GMA-gelatin solutions of different concentrations (5-20 wt.-%) by drying and rehydration. An increase of GMA-gelatin concentration from 5 wt.-% to 20 wt.-% led to an increased density of produced gelatin films and a decreasing water uptake of the films from 1160 wt.-% to 730 wt.-%, while the storage modulus was increasing about one order of magnitude from 440 Pa to 4090 Pa. The relative single and triple helix content was not influenced by the variation of polymer concentration.

Polymer-based therapeutic strategies require biomaterials with properties and functions tailored to the demands of specific applications leading to an increasing number of newly designed polymers. For the evaluation of those new materials, comprehensive biocompatibility studies including cyto-, tissue-, and immunocompatibility are essential. Recently, it could be demonstrated that star-shaped amino oligo(ethylene glycol)s (sOEG) with a number average molecular weight of 5 kDa and functionalized with the phenol-derived moieties desaminotyrosine (DAT) or desaminotyrosyl tyrosine (DATT) behave in aqueous solution like surfactants without inducing a substantial cytotoxicity, which may qualify them as solubilizer for hydrophobic drugs in aqueous solution. However, for biomedical applications the polymer solutions need to be free of immunogenic contaminations, which could result from inadequate laboratory environment or contaminated starting material. Furthermore, the materials should not induce uncontrolled or undesired immunological effects arising from material intrinsic properties. Therefore, a comprehensive immunological evaluation as perquisite for application of each biomaterial batch is required. This study investigated the immunological properties of sOEG-DAT(T) solutions, which were prepared using sOEG with number average molecular weights of 5 kDa, 10 kDa, and 20 kDa allowing analyzing the influence of the sOEG chain lengths on innate immune mechanisms. A macrophage-based assay was used to first demonstrate that all DAT(T)-sOEG solutions are free of endotoxins and other microbial contaminations such as fungal products. In the next step, the capacity of the different DAT(T)-functionalized sOEG solutions to induce cytokine secretion and generation of reactive oxygen species (ROS) was investigated using whole human blood. It was observed that low levels of the pro-inflammatory cytokines interleukin(IL)-1β and IL-6 were detected for all sOEG solutions but only when used at concentrations above 250 µg·mL-1. Furthermore, only the 20 kDa sOEG-DAT induced low amounts of ROS-producing monocytes. Conclusively, the data indicate that the materials were not contaminated with microbial products and do not induce substantial immunological adverse effectsin vitro,which is a prerequisite for future biological applications.

Design, synthesis, processing, and testing, or perhaps better altogether exploration, of biomaterials, which are intended to substitute native tissue, have generally been approached from one of two distinct perspectives (Figure ​1A).1A). Researchers with a background in chemistry or biology have been inspired by the natural surroundings of cells, the extracellular matrix (ECM). The ECM is a complex nanostructured system of fiber and network forming macromolecules as well as soluble compounds embedded in a hydrogel. The fiber and network forming macromolecules such as collagen and elastin enable the elastic deformability and recoverability of tissues. Water storage in the hydrogel is ruled by polysaccharide and proteoglycan components, such as glycosaminoglycans, for example, hyaluronic acid. The hydrogel furthermore counteracts the contraction by the fibers and the elastic network. At the same time, it allows the diffusion of gasses, ions, nutrients, and metabolites necessary for the supply of and communication between the cells. Anchoring of cells to the matrix as well as of the different macromolecular components is generally ruled by non-covalent, specific adhesion such as the interaction of the RGD sequence in, for example, fibronectin and integrins in cell membranes. The matrix is built up and degraded through hydrolytic as well as enzyme- and cell-mediated events, which in vivo leads to a continuous remodeling and renewal. In an attempt to learn from nature the macromolecular components of the ECM can be used or emulated, and selected functionalities of the ECM can be mimicked. Taking the ECM structure and functions as blueprint led to a much improved understanding of the interplay between cells and materials. However, materials designed in this way have rarely been advanced to technical or clinical applications. Examples for approaches in this field are the coating of polymers or metals with extracellular matrix extracts produced from sarcoma cells which are harvested and decellularized,[1] or the production of ECM on an artificial surface by cells which are removed prior to application. Such approaches suffer from an incomplete knowledge and limited control of the actual composition and chemical structure, as well as batch-to-batch variability of the biotechnologically produced ECM. Alternatively, full tissues are decellularized and used as guiding structure in tissue engineering.[2] From the perspective of the medical device design aiming at a specific clinical need, especially biomedical engineers have concentrated on formulating requirements, and used “from the shelf” materials to reach their goals.

Summary Biomaterials are of increasing importance in regenerative medicine and entail delivery systems in somatic cell therapies, matrices for tissue engineering or tissue regeneration. The evaluation of biomaterial induced biological effects remains a key issue in clinical application. Cell-based assays for potential cytotoxic and immunological responses have been developed but are often inadequate to address cell-type specific responses to biomaterials. To quantitatively monitor attachment, survival, proliferation and fusion-controlled differentiation of osteoclasts (bone resorbing cells), a High Content Screening (HCS) assay has been developed based on osteoclast differentiation of the murine monocytic cell line RAW 264.7. This assay was applied to investigate the influence of degradation products of polymers from gelatin and lysine diisocyanate, which display tailorable mechanical properties and have potential as biomaterials. The data show that the degradation products inhibit formation of multinuclear osteoclasts and suggest a potential support of bone regeneration by suppression of bone resorption.

Hydrogels prepared from gelatin and lysine diisocyanate ethyl ester provide tailorable elastic properties and degradation behavior. Their interaction with human aortic endothelial cells (HAEC) as well as human macrophages (Mɸ) and granulocytes (Gɸ) were explored. The experiments revealed a good biocompatibility, appropriate cell adhesion, and cell infiltration. Direct contact to hydrogels, but not contact to hydrolytic or enzymatic hydrogel degradation products, resulted in enhanced cyclooxygenase-2 (COX-2) expression in all cell types, indicating a weak inflammatory activation in vitro. Only Mɸ altered their cytokine secretion profile after direct hydrogel contact, indicating a comparably pronounced inflammatory activation. On the other hand, in HAEC the expression of tight junction proteins, as well as cytokine and matrix metalloproteinase secretion were not influenced by the hydrogels, suggesting a maintained endothelial cell function. This was in line with the finding that in HAEC increased thrombomodulin synthesis but no thrombomodulin membrane shedding occurred. First in vivo data obtained after subcutaneous implantation of the materials in immunocompetent mice revealed good integration of implants in the surrounding tissue, no progredient fibrous capsule formation, and no inflammatory tissue reaction in vivo. Overall, the study demonstrates the potential of gelatin-based hydrogels for temporal replacement and functional regeneration of damaged soft tissue.

Bone regeneration can be stimulated by implantation of biomaterials, which is especially important for larger bone defects. Here, healing potency of the porous ArcGel was evaluated in a critical-size calvarial bone defect in rats in comparison with clinical standard autologous bone and Bio-Oss® Collagen (BioOss), a bone graft material frequently used in clinics. Bone healing and metabolic processes involved were monitored longitudinally by [18F]-fluoride and [18F]-FDG μ-PET/CT 1d, 3d, 3w, 6w, and 12w post implantation. Differences in quality of bone healing were assessed by ex vivo μ-CT, mechanical tests and histomorphometry. The amount of bone formed after implantation of ArcGel was comparable to autologous bone and superior to BioOss (histomorphometry). Furthermore, microarchitecture of newly formed bone was more physiological and better functional in case of ArcGel (push-out tests). [18F]-FDG uptake increased until 3d after implantation, and decreased until 12w for both ArcGel and BioOss. [18F]-fluoride uptake increased until 3w post implantation for all materials, but persisted significantly longer at higher levels for BioOss, which indicates a prolonged remodelling phase. The study demonstrates the potential of ArcGel to induce restitutio ad integrum comparable with clinical standard autologous bone and better bone regeneration in large defects compared to a commercial state-of-the-art biomaterial.

Summary At concentrations above 15 wt-%, aqueous solutions of mixtures of aminoterminated poly(ethylene glycol)-block-poly(propylene glycol)-block-poly(ethylene glycol) block copolymers (PEPE) and hyaluronic acid show a reversible sol-gel-transition upon change of temperature. For non-aminoterminated PEPEs, this gel transition could be related to micellization and subsequent colloidal jamming of the micelles. Here, the mechanism of gelation for the aminoterminated compound is investigated by fluorescence spectroscopy and 1H-NMR spectroscopy. The aminoterminated PEPE also form micelles. The onset of micellization is temperature and concentration dependent, and can be tuned to 20–40 °C. Interestingly, with increasing molecular weight of the hyaluronic acid component, the micellization is observed at lower concentrations.

Ring-opening metathesis catalysis has received little attention as a means to functionalize or crosslink biopolymers in water since the required catalysts are usually not stable under these conditions. However, biopolymer solubility suggests such a procedure. We show that Grubbs first and second generation catalysts (in emulsion) as well as a water-soluble Hoveyda-Grubbs catalyst can be applied to crosslink glycidyl methacrylated gelatin with norbornene dicarboxylic acid in water by a cross metathesis-ring opening metathesis approach. A mechanistic study suggests that cross metathesis between the functionalized polymer and the cyclic olefin acts as an initiating step for the crosslinking reaction. Copyright © 2014 John Wiley & Sons, Ltd.

Hemocompatible materials are needed for internal and extracorporeal biomedical applications, which should be realizable by reducing protein and thrombocyte adhesion to such materials. Polyethers have been demonstrated to be highly efficient in this respect on smooth surfaces. Here, we investigate the grafting of oligo- and polyglycerols to rough poly(ether imide) membranes as a polymer relevant to biomedical applications and show the reduction of protein and thrombocyte adhesion as well as thrombocyte activation. It could be demonstrated that, by performing surface grafting with oligo- and polyglycerols of relatively high polydispersity (>1.5) and several reactive groups for surface anchoring, full surface shielding can be reached, which leads to reduced protein adsorption of albumin and fibrinogen. In addition, adherent thrombocytes were not activated. This could be clearly shown by immunostaining adherent proteins and analyzing the thrombocyte covered area. The presented work provides an important strategy for the development of application relevant hemocompatible 3D structured materials.

Commercial non-degradable glaucoma implants are often associated with undesired hypotony, fibrosis, long term failure, and damage of adjacent tissues, which may be overcome by a multifunctional polymeric microstent for suprachoroidal drainage. This study reports the design and fabrication of such devices with tailorable internal diameters (50–300 μm) by solvent-free, continuous hot melt extrusion from blends of poly[( e -caprolactone)- co -glycolide] and poly( e -caprolactone) [PCL]. A spatially directed release was supported by bilayered microstents with an internal drug-free PCL layer, and a quantitative description of release kinetics with diclofenac sodium as model drug was provided. Furthermore, the slow degradation pattern (> 1 year) was analyzed and potential effects of 1–5 wt.% drug loading on material properties were excluded. Translational aspects including sterilization by γ-irradiation on dry ice, in vitro biocompatibility, and in vivo implantation were addressed. The promising results support further functional analysis of long-term in vivo performance and suppression of disadvantageous capsule formation.

Summary Side chain functionalization of gelatin with tyrosine-derived moieties, desaminotyrosine (DAT) or desaminotyrosyl tyrosine (DATT), has been reported to lead to physical networks stabilized by aromatic interactions and hydrogen bonds, while the inherent ability of gelatin chains to organize in helices is suppressed. Here, the treatment of DAT and DATT gelatin films at defined temperatures (drying at 5 °C, freeze-drying, and freeze-thawing) were explored for the potential to additionally stabilize the hydrogels by increasing the content of helical domains as additional physical netpoints. The influence of the drying procedures on the hydrogel properties such as network morphology and mechanical properties were analyzed by WAXS, swelling, and rheological measurements. The triple helix content had a stabilizing effect on gelatin-based hydrogels at temperatures below the helix-to-coil transition. However, this effect was less pronounced at physiological conditions above the transition temperature, resulting in rapid dissolution of the physical gelatin networks.

Polymer network formation is an important tool for tailoring mechanical properties of polymeric materials. One option to synthesize a network is the addition of bivalent crosslinkers reacting with functional groups present in a polymer. In case of polymer network syntheses based on biopolymers, performing such a crosslinking reaction in water is sometimes necessary in view of the solubility of the biopolymer, such as gelatin, and can be beneficial to avoid potential contamination of the formed material with organic solvents in view of applications in biomedicine. In the case of applying diisocyanates for the crosslinking in water, it is necessary to show that the low molecular weight bifunctional crosslinker has fully reacted, while tailoring of the mechanical properties of the resulting hydrogels is possible despite the complex reaction mechanism. Here, the formation of gelatin-based hydrogel networks with the diisocyanates 2,4-toluene diisocyanate, 1,4-butane diisocyanate, and isophorone diisocyanate is presented. It is shown that extensive washing of materials is required to ensure full conversion of the diisocyanates. The use of different diisocyanates gives hydrogels covering a large range of Young’s moduli (12-450 kPa). The elongations at break (up to 83%) as well as the maximum tensile strengths (up to 410 kPa) of the hydrogels described here are much higher than for lysine diisocyanate ethyl ester crosslinked gelatin reported before. Rheological investigations suggest that the network formation in some cases is due to physical interactions and entanglements rather than covalent crosslink formation.

Gelatin can be covalently crosslinked in aqueous solution by application of diisocyanates like L-lysine diisocyanate ethyl ester in order to form hydrogels. Reaction of isocyanate groups with water is however a limiting factor in hydrogel network formation and can strongly influence the outcome of the crosslinking process. Here, diisocyanates with different water solubility and reactivity were applied for the formation of gelatin-based hydrogel networks and the mechanical properties of the hydrogels were investigated to gain a better understanding of starting material/ hydrogel property relations. L-Lysin diisocyanate ethyl ester (LDI), 2,4-toluene diisocyanate (TDI), 1,4-butane diisocyanate (BDI), and isophorone diisocyanate (IPDI) were selected, having different solubility in water ranging from 10-4 to 10-2 mol·L-1. BDI and LDI were estimated to have average reactive isocyanates groups, whereas TDI is highly reactive and IPDI has low reactivity. Formed hydrogels showed different morphologies and were partially very inhomogeneous. Gelation time (1 to 50 minutes), water uptake (300 to 900 wt.-%), and mechanical properties determined by tensile tests (E-moduli 35 to 370 kPa) and rheology (Shear moduli 4.5 to 19.5 kPa) showed that high water solubility as well as high reactivity leads to the formation of poorly crosslinked or inhomogeneous materials. Nevertheless, diisocyanates with lower solubility in water and low reactivity are able to form stable, homogeneous hydrogel networks with gelatin in water.

Biomaterials require thoroughin vitrotesting before being appliedin vivo. Unwanted contaminations of biomaterials but also their intrinsic properties can cause uncontrolled immune response leading to severe consequences for the patient. Therefore, immunological evaluation of materials for biomedical applications is mandatory before entering clinical application. In order to introduce physical netpoints, the aromatic compounds desaminotyrosine (DAT) and desaminotyrosyl-tyrosine (DATT) were successfully used to functionalize linear and star-shaped oligoethylene glycol (lOEG and sOEG) as previously described. The materials showed properties of surfactants and have potential to be used for solubilization of lipophilic drugs in water. Furthermore, the materials are susceptible for H2O2degradation as determined by MALDI-ToF MS analyses. This is important for potentialin vivoapplications, as macrophages can release reactive oxygen species (ROS) under inflammatory conditions. As it is known that surfactant solutions of high concentration can lead to cell lysis, the effects of OEG-DAT(T) solutions on murine RAW macrophages were investigated. Even at highest OEG-DAT(T) concentration of 1000 µg·mL-1the viability of the RAW cells was not significantly impaired. Additionally, the polymers were incubated with whole human blood and the production of inflammatory cytokines such as the tumor necrosis factor (TNF)-α and interleukin (IL)-6 was determined. Only at high concentrations, the OEG-DAT(T) solution induced low levels of TNF-α and IL-6, indicating that a mild inflammatory reaction could be expected when such high OEG-DAT(T) concentrations are appliedin vivo. Similarly, the OEG-DAT(T) solution did not induce ROS in monocytes and neutrophils after incubation with whole human blood. Conclusively, the data presented here demonstrate that OEG-DAT(T) do not lead to a substantial activation of the innate immune mechanisms and could therefore be investigated for solubilizing pharmaceutical agents.

The extracellular matrix (ECM) is a nano-structured, highly complex hydrogel, in which the macromolecules are organized primarily by non-covalent interactions. Here, in a biomimetic approach, the decorin-derived collagen-binding peptide LSELRLHNN was grafted to hyaluronic acid (HA) in order to enable the formation of a supramolecular hydrogel network together with collagen. The storage modulus of a mixture of collagen and HA was increased by more than one order of magnitude ( G ′ = 157 Pa) in the presence of the HA-grafted peptide compared to a mixture of collagen and HA ( G ′ = 6 Pa). The collagen fibril diameter was decreased, as quantified using electron microscopy, in the presence of the HA-grafted peptide. Here, the peptide mimicked the function of decorin by spatially organizing collagen. The advantage of this approach is that the non-covalent crosslinks between collagen molecules and the HA chains created by the peptide form a reversible and dynamic hydrogel, which could be employed for a diverse range of applications in regenerative medicine. Statement of Significance Biopolymers of the extracellular matrix (ECM) like collagen or hyaluronan are attractive starting materials for biomaterials. While in biomaterial science covalent crosslinking is often employed, in the native ECM, stabilization and macromolecular organization is primarily based on non-covalent interactions, which allows dynamic changes of the materials. Here, we show that collagen-binding peptides, derived from the small proteoglycan decorin, grafted to hyaluronic acid enable supramolecular stabilization of collagen hydrogels. These hydrogels have storage moduli more than one order of magnitude higher than mixtures of collagen and hyaluronic acid. Furthermore, the peptide supported the structural organization of collagen. Such hydrogels could be employed for a diverse range of applications in regenerative medicine. Furthermore, the rational design helps in the understanding ECM structuring.

Decorin is a small leucine-rich repeat proteoglycan supporting collagen fibril formation by controlling the rate of collagen fibrillogenesis and fibril dimensions. Peptides derived from the inner surface of decorin have been shown to bind to collagen, while peptides derived from the outer surface do not display such binding affinity. As typical secondary structural elements such as β-sheets and α-helical regions were found in the decorin X-ray crystal structure, here it was investigated by Circular Dichroism (CD) spectroscopy in solution, whether the same structural elements can be found in the derived peptides. Here it is shown that the peptide derived from decorin’s outer surface has the propensity to adopt helical conformation, as it was found in the crystal structure. The results were more pronounced in 80 vol% TFE solution, which led to an increase in the number as well as the length of helices. In contrast, peptides derived from the inner surface had a higher tendency to adopt β-sheet conformation, also in TFE, which corresponds to the conformation of the original sequence in the crystal structure of decorin. This suggests that the peptides derived from decorin adopt the structures present in the native protein.

Preparation of three-dimensionally architectured porous biomaterials can be achieved in a one-step process by stabilizing gelatin with L-lysine diisocyanate ethyl ester (LDI) in water. The reaction of gelatin with LDI in presence of water leads to the formation of oligourea bridges between gelatin molecules and oligourea chains grafted on gelatin. The number and the length of the bridges, as well as of the grafted chains strongly depend on the concentration of the LDI used for the stabilization, and this has huge influence on the mechanical properties of the material on different hierarchical levels. Higher LDI concentrations yield materials with increased deformation resistance in tensile tests due to the higher number of covalent and physical netpoints in the material. However, mechanical properties determined on the micro-level by AFM indentation showed the opposite trend, i.e. a decrease of Young’s modulus with increasing LDI content. This was interpreted by a decreasing number of shorter oligourea bridges between gelatin chains with decreasing LDI content.

Materials for biomedical applications are often chosen for their bulk properties. Other requirements such as a hemocompatible surface shall be fulfilled by suitable chemical functionalization. Here we show, that linear, side-chain methylated oligoglycerols (OGMe) are more stable to oxidation than oligo(ethylene glycol) (OEG). Poly(ether imide) (PEI) membranes functionalized with OGMes perform at least as good as, and partially better than, OEG functionalized PEI membranes in view of protein resistance as well as thrombocyte adhesion and activation. Therefore, OGMes are highly potent surface functionalizing molecules for improving the hemocompatibility of polymers.

Telechelic oligomers are attractive starting materials for the preparation of materials with tailorable properties. Here, peptide chains with defined molecular weight were obtained by controlled degradation of gelatin with hydroxylamine, which resulted in the cleavage of asparaginyl-glycine bonds and formation of new aspartyl hydroxamates and amino endgroups. The reaction of gelatin with hydroxylamine resulted in fragments with molecular weights of 15, 25, 37, and 50 kDa (determined by SDS-PAGE) independently of the reaction time and conditions. The fragment mixture showed typical single and triple helical organization in WAXS spectra, but rheological studies showed lower G′ and G″ values for gels from the fragment mixture than from gelatin, and lower gel-sol transitions temperatures. A more narrow distribution was found for the fragment mixture (M n = 25 kDa, PDI = 1.4) than for commercial gelatin. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Polyetherimides have been evaluated as non-toxic and steam-sterilizable and are therefore potentially suited for biomedical applications. To enable a broader range of potential applications, polyetherimides with lower Tg, higher elasticity at room temperature and better processability are required. Our concept was to explore, whether the incorporation of 3-methoxy-1,2-propanediol moieties in the main chain lead to a reduction of Tg and increase the elastic properties of the polymer compared to commercially available polyetherimides from 4,4′-(4,4′-isopropylidenediphenoxy)bis(phthalic anhydride) and 1,3-diaminobenzene. Two different monomers were synthesized and co-condensated with each other or using 4,4,4′-(4,4′-isopropylidenediphenoxy)bis(phthalic anhydride), respectively. The results proofed the successful synthesis and polymerization leading to polymers with molecular weights up to Mn = 6,400 g/mol. The polymers showed lowered Tg, resistance to heat up to 400 °C, tendencies to reduced contact angles and partially reduced E-moduli in comparison to the commercial polyetherimide ULTEM 1000.

Hydrolytic degradation of poly(e-caprolactone) [PCL] can be enhanced by introduction of 8 wt.% glycolide leading to poly[(e-caprolactone)-co-glycolide] (PCG), which has a low elongation at break eB of 4%. PCG/PCL blends (50/50 w/w) combined the advantageous features of its individual components such as mechanical properties similar to pure PCL (eB, Blend: 900 ± 230%; eB, PCL: 730 ± 50 at 20 °C), water uptake rates during degradation similar to pure PCG, and linear mass loss during bulk degradation independent from sample dimensions. The outcome of cytotoxicity studies was depending on the cell type with promising results, e.g., for Tenon fibroblasts. Easy processing of the blend was demonstrated by melt compression, foaming with CO2, and hot melt extrusion, suggesting a wide applicability as biomaterial, e.g., as drug carrier.

A peptide showing propensity for the adoption of β-sheet conformation was synthesized in order to develop a defined molecular building block as part of a toolbox for the development of polymer networks based on supramolecular interactions. The peptide was synthesized by microwave-assisted solid phase peptide synthesis and the purification was performed by Reversed Phase-High Performance Liquid Chromatography (RP-HPLC), from which a purity higher than 95 mol-% was obtained. The calculated mass was confirmed by Matrix Assisted Laser Desorption Ionization-Time of Flight-Mass Spectrometry (MALDI-ToF-MS). Further characterization of the peptide was performed by IR and 2D TOCSY, NOESY, and HSQC NMR spectroscopy, which confirmed the identity and the sequence of the peptide.

Biomaterial-induced autoregeneration requires materials with distinct tailored mechanical and thermal properties, water uptake and swelling properties as well as degradation behavior. Furthermore, before any biomaterial can be applied in vivo, in vitro studies should be performed that confirm the suitability for such applications. One facet in this process is the evaluation of endotoxin loads and immunogenic response to the material to avoid an unspecific activation of the immune system, which otherwise might cause fever and could lead to life–threatening pathologies. In this study, gelatins functionalized with desaminotyrosine (DAT) or desaminotyrosyl tyrosine (DATT) were investigated in terms of their endotoxin content and their potential to induce an inflammatory cytokine response in macrophages. Using the Limulus amebocyte lysate (LAL) test it could be shown that the endotoxin content was substantially reduced by using certified low endotoxin containing gelatin and performing the gelatin functionalization under cleanroom conditions. Furthermore, production of inflammatory cytokines such as interleukin 6 (IL-6) and tumor necrosis factor–alpha (TNFα) of an immune relevant macrophage cell line was significantly reduced for these materials. The survival of the macrophage cell line in the presence of DAT(T)-functionalized gelatins was not influenced by both materials. Therefore, DAT- and DATT-functionalized gelatins were shown to have passed the tests concerning immunological responses important for their applicability in vivo.

A family of oligo[(ɛ-caprolactone)-co-glycolide]dimethacrylate (oCG-DMA) derived networks of different glycolide contents as well as precursor molecular weights has been synthesized by crosslinking oCG-DMA, providing matrices of different hydrophilicity, network density, and morphology at body temperature. Such networks were loaded with a hydrophilic model drug, ethacridine lactate, either before crosslinking or afterwards by swelling in drug solution. Disadvantageous alterations of the shape-memory functionality and degradation characteristics were observed only in few loaded materials. Loading by swelling generally resulted in low payloads, which slightly increased for more hydrophilic polymer networks, and a substantial burst and fast subsequent release for all investigated materials. Loading before crosslinking gave almost no burst and higher subsequent release rates over longer periods of time. Overall, depending on the needs of a specific application, a material from this polymer family with the desired mechanical properties, shape-memory functionality, and degradation pattern can be selected and combined with drugs when considering that (i) loading by swelling is best suited for applications that require high initial doses and (ii) loading before crosslinking allows easy variation of payloads and low burst release for therapeutics that are non-sensitive to chemical alterations during crosslinking.

Polyester urethane networks are versatile polymer systems as it is possible to tailor their mechanical properties and their hydrolytic degradation profile. For biomedical applications, the biodegradability as well as the thermomechanical properties of the polymer networks during the course of degradation is of importance. Therefore, we investigated the change of thermomechanical properties of networks based on star-shaped precursors of rac-dilactide and diglycolide, e-caprolactone, or p-dioxanone, respectively, during hydrolytic degradation. Degradation rate and mechanical properties of the polymer networks were tailored by crosslink density, comonomers, and by changing the glass transition temperature. Most importantly, the degradation of the networks led to a controlled, step-by-step change of the mechanical properties of the networks.

Degradable shape-memory polymers are multifunctional materials with broad applicability for medical devices. They are designed to acquire their therapeutically relevant shape and mechanical properties after implantation. In this study, the potential of a completely amorphous shape-memory polymer matrix for controlled drug release was comprehensively characterized according to a four step general strategy which provides concepts for validating multifunctional materials for pharmaceutical applications. Independent functionalities are thereby crucial for fully exploiting the potential of the materials. The copolyester urethane network was synthesized by crosslinking star-shaped tetrahydroxy telechelics of oligo[(rac-lactide)-co-glycolide] with an aliphatic diisocyanate. In step 1 of the four step characterization procedure, this material showed the thermal and mechanical properties, which are required for the shape-memory effect under physiological conditions. Shape recovery could be realized by a one-step or a multi-step methodology. In step 2, feasibility of drug loading of pre-formed shape-memory networks has been demonstrated with drugs of different hydrophobicities. The presence of drugs did not disturb the material's functionalities directly after loading (step 3) and under release conditions (step 4). A predictable release of about 90% of the payload in 80 days was observed. Overall, the synthesized amorphous polymer network showed three independent functionalities, i.e., a shape-memory effect combined with biodegradability and controlled drug release.

Structured hydrogels showing form stability and elastic properties individually tailorable on different length scales are accessible in a one-step process. They support cell adhesion and differentiation and display growing pore size during degradation. In vivo experiments demonstrate their efficacy in biomaterial-induced bone regeneration, not requiring addition of cells or growth factors.

In the fields of surgery and regenerative medicine, it is crucial to understand the interactions of proteins with the biomaterials used as implants. Protein adsorption directly influences cell-material interactions in vivo and, as a result, regulates, for example, cell adhesion on the surface of the implant. Therefore, the development of suitable analytical techniques together with well-defined model systems allowing for the detection, characterization, and quantification of protein adsorbates is essential. In this study, a protocol for the deposition of highly stable, thin gelatin-based films on various substrates has been developed. The hydrogel films were characterized morphologically and chemically. Due to the obtained low thickness of the hydrogel layer, this setup allowed for a quantitative study on the interaction of human proteins (albumin and fibrinogen) with the hydrogel by Quartz Crystal Microbalance with Dissipation Monitoring (QCM-D). This technique enables the determination of adsorbant mass and changes in the shear modulus of the hydrogel layer upon adsorption of human proteins. Furthermore, Secondary Ion Mass Spectrometry and principal component analysis was applied to monitor the changed composition of the topmost adsorbate layer. This approach opens interesting perspectives for a sensitive screening of viscoelastic biomaterials that could be used for regenerative medicine.

Protein adsorption is considered to be the most important factor of the interaction between polymeric biomaterials and body fluids or tissues. Water-mediated hydrophobic and hydration forces as well as electrostatic interactions are believed to be the major factors of protein adsorption. A systematic analysis of various monolayer systems has resulted in general guidelines, the so-called "Whitesides rules". These concepts have been successfully applied for designing various protein-resistant surfaces and are being studied to expand the understanding of protein-material interactions beyond existing limitations. Theories on the mechanisms of protein adsorption are constantly being improved due to the fast-developing analytical technologies. This Review is aimed at improving these empirical guidelines with regard to present theoretical and analytical advances. Current analytical methods to test mechanistic hypotheses and theories of protein-surface interactions will be discussed. Special focus will be given to state-of-the-art bioinert and biospecific coatings and their applications in biomedicine.

Critical bone defects do not heal by themselves, but the regeneration process can be supported by biomaterial implants. Combinations of synthetic polymers, intended to provide the required mechanical strength and processability, and biopolymers, giving cells a suitable environment for proliferation and inducing bone growth, have recently drawn attention in order to provide multifunctional implants. In this chapter, the combination of the different polymer classes on the molecular level and by surface functionalization is discussed, with emphasis on physicochemical properties and the biological functions of the materials as well as future trends in this research field.

Biopolymer-based materials are based on re-growing resources and are attractive for biomedical applications, as they can inherently combine degradability in vivo, can offer sites of adhesion for cells and proteins, often show good biocompatibility and may additionally be used to release embedded bioactive molecules. However, their selection and efficient use for specific applications require an understanding of molecular principles and relationships between the molecular and macroscopic level to establish distinct properties and functions. Here, synthetic routes are described, which allow tailoring properties and functions of biopolymer-based materials. The biological evaluation of such materials is discussed, with a special emphasis on their application in controlled release systems such as hydrogels and particulate carriers.

Polymeric hydrogels typically release their drug payload rapidly due to their high water content and the diffusivity for drug molecules. This study proposes a multimaterial system to sustain the release by covering the hydrogel with a poly(alkyl-2-cyanoacrylate) [PACA]-based film, which should be formed by an in situ polymerization on the hydrogel surface initiated upon contact with water. A series of PACA-hydrogel hybrid systems with increasing PACA side chain hydrophobicity was prepared using physically crosslinked alginate films and hydrophilic diclofenac sodium as model hydrogel/drug system. Successful synthesis of PACA at the hydrogel surface was confirmed and the PACA layer was identified to be most homogeneous for poly(n-butyl-2-cyanoacrylate) on both the micro- and nanolevel. At the same time, the diclofenac release from the hybrid systems was substantially sustained from ~ 1 day for unmodified hydrogels up to > 14 days depending on the type of PACA employed as diffusion barrier. Overall, in situ polymerized PACA films on hydrogels may be widely applicable to various hydrogel matrices, different matrix sizes as well as more complex shaped hydrogel carriers.

Physically crosslinked hydrogels based on gelatin functionalized with desaminotyrosine (DAT) (giving Gel-DAT) or desaminotyrosyl tyrosine (DATT) (resulting in Gel-DATT) have shown high potential as biomaterials. Here, protein adsorption to the functionalized gelatins in comparison to gelatin was quantified to see if the functionalization and chain organization of gelatins has an influence on the amount of proteins being adsorbed. For this purpose, gelatin, Gel-DAT, and Gel-DATT were incubated with water or aq. solutions of bovine serum albumin (BSA), fibrinogen, or fibronectin, respectively, at physiological concentrations. Protein concentrations in the supernatant were determined with the bicinchoninic acid (BCA) assay before and after the contact. BSA adsorption to the materials was influenced as well by the hydrophobicity of the material as the degree of swelling, with the observation that higher protein concentrations led to lower protein adsorption. The highest amount of fibronectin was adsorbed to Gel-DAT, followed by gelatin and Gel-DATT, with only small differences for different initial protein concentrations. Fibrinogen adsorption increased with increasing concentration. In the future, adsorption studies based on specific antibody-based techniques might enable quantification of the proteins also in competition assays and direct quantification of adsorbed material.

Stimuli-sensitive materials can change properties upon exposure to an external stimulus. Thermoreversible gelation upon heating is one example for such a stimuli sensitivity. Here, it is of significance to tailor the transition temperature and to achieve large changes of G’ and the viscosity. Grafting of the thermosensitive poly(ethylene glycol-b-propylene glycol-b-ethylene glycol)s (PEPEs) to pectin was performed in order to investigate if tailoring of the sol-gel-transition temperature can be achieved by adjusting the grafting ratio. PEPEs were aminated and grafted to the polysaccharide via EDC coupling as shown by FTIR. The sol-gel transition of the pectin, PEPE, and the grafted system (PGP) was investigated by rheology. The gelation temperature (Tgel) of the system could be adjusted by varying the grafting density of PEPE onto pectin as well as by the concentration of the thermosensitive polymer in aqueous solution. A concentration of 15 – 20 wt% of the grafted system in water led to gelation temperatures in the range of 25 – 33 °C and the critical micelle concentration (CMC) and critical micelle temperature (CMT) of the grafted systems were determined by UV spectroscopy. The viscosity and the G’ increased by four orders of magnitudes at Tgel, which is comparable to PEPEs alone, but could be reached at lower PEPE concentrations. In the future, a thorough mechanistic investigation of the gelation process would be of interest.

Introduction Poly(alkyl-2-cyanoacrylates) (PACAs) are degradable biomaterials that are clinically applied as surgical glue and studied as a matrix for particulate drug carriers such as nanoparticles or micro/nanocapsules. The stability of capsule walls is essential to avoid leakage of encapsulated compounds. Methods PACA capsules and (co)polymer films were prepared and characterization of their morphologies and thermal properties was performed. Results Thin-walled capsules that allow for a large internal volume to carry the payload were instable due to the high brittleness of PACA. Strategies to reduce the glass transition temperature (Tg) from values as high as ~120°C included plasticization by solvents and copolymerization approaches. By using the latter, the Tg of commonly used n-butylcyanoacrylate could be reduced up to 30 K, following predictions of mixed-system glass transition temperatures obtained, for example, by the Fox equation. Conclusions Thin-walled PACA capsules may allow for large payloads in the field of drug delivery and beyond, but require modifications of the PACA to improve capsule stability by more elastic capsule walls.

Biomaterials are used in regenerative medicine for induced autoregeneration and tissue engineering. This is often challenging, however, due to difficulties in tailoring and controlling the respective material properties. Since functionalization is expected to offer better control, in this study gelatin chains were modified with physically interacting groups based on tyrosine with the aim of causing the formation of physical crosslinks. This method permits application-specific properties like swelling and better tailoring of mechanical properties. The design of the crosslink strategy was supported by molecular dynamic (MD) simulations of amorphous bulk models for gelatin and functionalized gelatins at different water contents (0.8 and 25 wt.-%). The results permitted predictions to be formulated about the expected crosslink density and its influence on equilibrium swelling behavior and on elastic material properties. The models of pure gelatin were used to validate the strategy by comparison between simulated and experimental data such as density, backbone conformation angle distribution, and X-ray scattering spectra. A key result of the simulations was the prediction that increasing the number of aromatic functions attached to the gelatin chain leads to an increase in the number of physical netpoints observed in the simulated bulk packing models. By comparison with the Flory-Rehner model, this suggested reduced equilibrium swelling of the functionalized materials in water, a prediction that was subsequently confirmed by our experimental work. The reduction and control of the equilibrium degree of swelling in water is a key criterion for the applicability of functionalized gelatins when used, for example, as matrices for induced autoregeneration of tissues.

Combining gelatins functionalized with the tyrosine-derived groups desaminotyrosine or desaminotyrosyl tyrosine with hydroxyapatite (HAp) led to the formation of composite materials with much lower swelling ratios than those of the pure matrices. Shifts of the infra-red (IR) bands related to the free carboxyl groups could be observed in the presence of HAp, which suggested a direct interaction of matrix and filler that formed additional physical cross-links in the material. In tensile tests and rheological measurements the composites equilibrated in water had increased Young's moduli (from 200 kPa up to 2 MPa) and tensile strengths (from 57 kPa up to 1.1 MPa) compared with the matrix polymers without affecting the elongation at break. Furthermore, an increased thermal stability of the networks from 40 to 85 degrees C could be demonstrated. The differences in the behaviour of the functionalized gelatins compared with pure gelatin as a matrix suggested an additional stabilizing bond between the incorporated aromatic groups and the HAp as supported by the IR results. The composites can potentially be applied as bone fillers.

Gelatin is a non-immunogenic and degradable biopolymer, which is widely applied in the biomedical field e. g. for drug capsules or as absorbable hemostats. However, gelatin materials present limited and hardly reproducible mechanical properties especially in aqueous systems, particularly caused by the uncontrollable partial renaturation of collagen-like triple helices. Therefore, mechanically demanding applications for gelatin-based materials, such as vascular patches, i.e. hydrogel films that seal large incisions in vessel walls, and for induced autoregeneration, are basically excluded if this challenge is not addressed. Through the synthesis of a defined chemical network of gelatin with hexamethylene diisocyanate (HDI) in DMSO, the self-organization of gelatin chains could be hindered and amorphous gelatin films were successfully prepared having Young's moduli of 60-530 kPa. Transferring the crosslinking reaction with HDI and, alternatively, ethyl lysine diisocyanate (LDI), to water as reaction medium allowed the tailoring of swelling behaviour and mechanical properties by variation of crosslinker content while suppressing the formation of helices. The hydrogels had Young's moduli of 70-740 kPa, compressive moduli of 16-48 kPa, and degrees of swelling of 300-800 vol%. Test reactions investigated by ESI mass spectrometry allowed the identification and quantification of reaction products of the crosslinking reaction. The HDI crosslinked networks were stabilized by direct covalent crosslinks (ca. 10 mol%), supported by grafting (50 mol%) and blending of hydrophobic oligomeric chains. For the LDI- based networks, less crosslinked (3 mol%) and grafted species (5 mol%) and much higher amounts of oligomers were observed. The adjustable hydrogel system enables the application of gelatin-based materials in physiological environments.