Search

International audience; Surfactant flooding is one of the Chemical Enhanced Oil Recovery (cEOR) methods used to meet the growing demand for oil. It consists in injecting an aqueous formulation containing surfactants, whose performance, both in terms of incremental oil production and surfactant adsorption, is assessed in the laboratory with coreflood tests. Currently, coreflood effluents are collected in tubes throughout the experiment and the analyses are performed offline. Surfactants are measured in the aqueous phase by Hyamine assay or by liquid chromatography. It is noteworthy that these analyses may be difficult to carry out since the effluents may contain stable emulsions. Moreover, it is unclear whether all surfactants are in the aqueous phase, or whether they are partly trapped in the oil phase. To overcome these difficulties and quantify surfactants reliably in coreflood effluents, we have developed an online experimental setup that includes: a dilution “millifluidic” chip to transfer the surfactants in the aqueous phase, a “microfluidic” membrane-based separation device to separate oil from the aqueous phase, and an online UV–visible spectrometer to measure the surfactant concentration. This setup was successfully validated with model fluid mixtures and was evaluated on real systems. Finally, it was tested under representative conditions of coreflood experiments. The obtained results proved the efficiency of the setup to facilitate the quantification of the surfactants in the effluents which clearly improves the accuracy of the measurements.

This protocol describes the manufacturing of reproducible and inexpensive microfluidic devices covering the whole pipeline for crystallizing proteins on-chip with the dialysis method and allowing in situ single-crystal or serial crystallography experiments at room temperature. The protocol details the fabrication process of the microchips, the manipulation of the on-chip crystallization experiments and the treatment of the in situ collected X-ray diffraction data for the structural elucidation of the protein sample. The main feature of this microfabrication procedure lies on the integration of a commercially available, semipermeable regenerated cellulose dialysis membrane in between two layers of the chip. The molecular weight cut-off of the embedded membrane varies depending on the molecular weight of the macromolecule and the precipitants. The device exploits the advantages of microfluidic technology, such as the use of minute volumes of samples (

We theoretically investigate the role of solutal free convection on the diffusion of a buoyant solute at the microfluidic scales, $\simeq 5$--$500~\mu$m. We first consider a horizontal microfluidic slit, one half of which initially filled with a binary solution (solute and solvent), and the other half with pure solvent. The buoyant forces generate a gravity current that couples to the diffusion of the solute. We perform numerical resolutions of the 2D model describing the transport of the solute in the slit. This study allows us to highlight different regimes as a function of a single parameter, the Rayleigh number $\text{Ra}$ which compares gravity-induced advection to solute diffusion. We then derive asymptotic analytical solutions to quantify the width of the mixing zone as a function of time in each regime and establish a diagram that makes it possible to identify the range of $\text{Ra}$ and times for which buoyancy does not impact diffusion. In a second step, we present numerical resolutions of the same model but for a 3D microfluidic channel with a square cross-section. We observe the same regimes as in the 2D case, and focus on the dispersion regime at long time scales. We then derive the expression of the 1D dispersion coefficient for a channel with a rectangular section, and analyse the role of the transverse flow in the particular case of a square section. Finally, we show that the impact of this transverse flow on the solute transport can be neglected for most of the microfluidic experimental configurations., Comment: 38 pages, 15 figures

In the present work, we use Mach-Zehnder interferometry to thoroughly investigate the drying dynamics of a 2D confined drop of a charged colloidal dispersion. This technique makes it possible to measure the colloid concentration field during the drying of the drop at a high accuracy (about 0.5%) and with a high temporal and spatial resolution (about 1 frame per s and 5 μm per pixel). These features allow us to probe mass transport of the charged dispersion in this out-of-equilibrium situation. In particular, our experiments provide the evidence that mass transport within the drop can be described by a purely diffusive process for some range of parameters for which the buoyancy-driven convection is negligible. We are then able to extract from these experiments the collective diffusion coefficient of the dispersion D(φ) over a wide concentration range φ = 0.24-0.5, i.e. from the liquid dispersed state to the solid glass regime, with a high accuracy. The measured values of D(φ) ≃ 5-12D0 are significantly larger than the simple estimate D0 given by the Stokes-Einstein relation, thus highlighting the important role played by the colloidal interactions in such dispersions. This journal is, info:eu-repo/semantics/published

International audience; We report the fabrication of permeable membranes for microfluidic dialysis applications in poly(dimethylsiloxane) (PDMS) channels. A maskless UV projection device was used to photo-pattern long hydrogel membranes (mm-cm) with a spatial resolution of a few microns in PDMS chips integrating also micro-valves. We show in particular that multi-layer soft lithography allows one to deplete oxygen from the PDMS walls using nitrogen gas flow and therefore makes possible in-situ UV-induced polymerization of hydro-gels. We also report a simple surface modification of the PDMS channels leading to strongly anchored hydrogel membranes that can withstand trans-membrane pressure drops up to 1 bar without leakages. We then measured the Darcy permeability of these membranes and estimated their cutoff by measuring the kinetics of diffusion of macromolecules of different sizes through the membrane. Finally, we illustrate the opportunities offered by such microfluidic chips for dialysis applications by observing in real time the crystallization of a model protein in a chamber of a few nanoliters.

We report the fabrication of highly permeable membranes in poly(ethylene glycol) diacrylate (PEGDA) channels, for investigating ultra- or micro-filtration, at the microfluidic scale. More precisely, we used a maskless UV projection setup to photo-pattern PEG-based hydrogel membranes on a large scale (mm-cm), and with a spatial resolution of a few microns. We show that these membranes can withstand trans-membrane pressure drops of up to 7 bar without any leakage, thanks to the strong anchoring of the hydrogel to the channel walls. We also report in situ measurements of the Darcy permeability of these membranes, as a function of the deposited energy during photo-polymerization, and their formulation composition. We show that the use of PEG chains as porogens, as proposed in [Lee et al., Biomacromolecules, 2010, 11, 3316], significantly increases the porosity of the hydrogels, up to Darcy permeabilities of about 1.5 × 10-16 m2, while maintaining the strong mechanical stability of the membranes. We finally illustrate the opportunities offered by this technique, by investigating frontal filtration of colloidal dispersions in a straight microfluidic channel.

International audience; In flow-coating processes at low substrate velocity , solvent evaporation occurs during the film withdrawal and the coating process yields directly a dry deposit. In this regime, often referred to as the evaporative regime, several works performed on blade-coating-like configurations have reported a deposit thickness h d proportional to the inverse of the substrate velocity V. Such a scaling can be easily derived from simple mass conservation laws, assuming that evaporation occurs on a constant distance, referred to as the evaporation length, noted L ev in the present paper and of the order of the meniscus size. However the case of colloidal dispersions deserves further attention. Indeed, the coating flow leads to a wet film of densely-packed colloids before the formation of the dry deposit. This specific feature is related to the porous nature of the dry deposit, which can thus remain wet when capillary forces are strong enough to prevent the receding of the solvent through the pores of the film (the so-called pore-emptying). The length of this wet film may be possibly much larger than the menis-cus size, therefore modifying the solvent evaporation rate, as well as the scaling h d ∼ 1/V. This result was suggested recently by different groups using basic modeling and assuming for simplicity an uniform evaporation rate over the wet film. In this article, we go a step further and investigate the effect of multi-dimensional vapor mass transfer in the gas phase on L ev and h d in the specific case of colloidal dispersions. Using simplified models, we first provide analytical expressions in asymptotic cases corresponding to 1D or 2D diffusive vapor transport. These theoretical investigations then led us to show that L ev is independent of the evaporation rate amplitude, and roughly independent of its spatial distribution. Conversely, h d strongly depends on the characteristics of vapor mass transfer in the gas phase, and different scaling laws are obtained for the 1D or the 2D case. These theoretical findings are finally tested by comparison with experimental results supporting our theoretical simplified approach.

International audience; This paper reports a versatile microfluidic chip developed for on-chip crystallization of proteins through the dialysis method and in situ X-ray diffraction experiments. A microfabrication process enabling the integration of regenerated cellulose dialysis membranes between two layers of the microchip is thoroughly described. We also describe a rational approach for optimizing on-chip protein crystallization via chemical composition and temperature control, allowing the crystal size, number and quality to be tailored. Combining optically transparent microfluidics and dialysis provides both precise control over the experiment and reversible exploration of the crystallization conditions. In addition, the materials composing the microfluidic chip were tested for their transparency to X-rays in order to assess their compatibility for in situ diffraction data collection. Background scattering was evaluated using a synchrotron X-ray source and the background noise generated by our microfluidic device was compared to that produced by commercial crystal-lization plates used for diffraction experiments at room temperature. Once crystals of 3 model proteins (ly-sozyme, IspE, and insulin) were grown on-chip, the microchip was mounted onto the beamline and partial diffraction data sets were collected in situ from several isomorphous crystals and were merged to a complete data set for structure determination. We therefore propose a robust and inexpensive way to fabricate microchips that cover the whole pipeline from crystal growth to the beam and does not require any handling of the protein crystals prior to the diffraction experiment, allowing the collection of crystallographic data at room temperature for solving the three-dimensional structure of the proteins under study. The results presented here allow serial crystallography experiments on synchrotrons and X-ray lasers under dynamically controllable sample conditions to be observed using the developed microchips.

We investigate the impact of buoyancy on the solute mass transport in an evaporating liquid mixture (non-volatile solute $+$ solvent) confined in a slit perpendicular to the gravity. Solvent evaporation at one end of the slit induces a solute concentration gradient which in turn drives free convection due to the difference between the densities of the solutes and the solvent. From the complete model coupling mass transport and hydrodynamics, we first use a standard Taylor-like approach to derive a one dimensional non-linear advection-dispersion equation describing the solute concentration process for a dilute mixture. We then perform a complete analysis of the expected regimes using both scaling analysis and asymptotic solutions of this equation. The validity of this approach is confirmed using a thorough comparison with the numerical resolution of both the complete model and the 1D advection-dispersion equation. Our results show that buoyancy-driven free convection always impacts solute mass transport at long time scales, dispersing solutes in a steadily increasing length scale along the slit. Beyond this confined drying configuration, our work also provides an easy way for evaluating the relevance of buoyancy on mass transport in any other microfluidic configuration involving concentration gradients., Comment: 12 pages, 5 figures

We first report an original setup that enables continuous measurements of stresses induced by the drying of confined drops of complex fluids. This setup is mainly based on a precision scale working with an electromagnetic force compensation technique that provides accurate measurements of forces, while allowing simultaneously controlled evaporation rates, in situ microscopic observations, and thus quantitative estimates of normal stresses. We then performed an extensive study of the drying of a charged colloidal dispersion using this setup. Stress measurements clearly show the emergence of large tensile stresses during drying, well-before the solidification stage evidenced by the invasion of the porous colloidal material by air. Combined measurements of solid deformation and concentration profiles (particle tracking, Raman micro-spectroscopy) help us to demonstrate that these stresses are due to the formation of a solid at a low volume fraction, which further undergoes drying-induced shear deformations up to the colloid close-packing, as also supported by large deformation poroelastic modeling. Above all, our results highlight the importance of repulsive colloidal interactions in the build-up of mechanical stresses during drying.

In view of the extensive increase of flexible devices and wearable electronics, the development of polymer micro-electro-mechanical systems (MEMS) is becoming more and more important since their potential to meet the multiple needs for sensing applications in flexible electronics is now clearly established. Nevertheless, polymer micromachining for MEMS applications is not yet as mature as its silicon counterpart, and innovative microfabrication techniques are still expected. We show in the present work an emerging and versatile microfabrication method to produce arbitrary organic, spatially resolved multilayer micro-structures, starting from dilute inks, and with possibly a large choice of materials. This approach consists in extending classical microfluidic pervaporation combined with MIcro-Molding In Capillaries. To illustrate the potential of this technique, bilayer polymer double-clamped resonators with integrated piezoresistive readout have been fabricated, characterized, and applied to humidity sensing. The present work opens new opportunities for the conception and integration of polymers in MEMS.

Raspberry-like magnetic nanoclusters are synthesized and subsequently self-assembled to form a bulk metamaterial exhibiting strong isotropic optical magnetism in visible light. The magnetic response of the nanoclusters (metamolecules) and of the final assembled material are measured by independent optical experiments. The validity of the effective permeability parameter is probed by spectroscopic ellipsometry at variable incidence. Numerical simulations confirm the measurements.

We present an original microfluidic technique coupling pervaporation and the use of Quake valves to fabricate microscale materials (∼10 × 100 μm(2) × 1 cm) with composition gradients along their longest dimension. Our device exploits pervaporation of water through a thin poly(dimethylsiloxane) (PDMS) membrane to continuously pump solutions (or dispersions) contained in different reservoirs connected to a microfluidic channel. This pervaporation-induced flow concentrates solutes (or particles) at the tip of the channel up to the formation of a dense material. The latter invades the channel as it is constantly enriched by an incoming flux of solutes/particles. Upstream Quake valves are used to select which reservoir is connected to the pervaporation channel and thus which solution (or dispersion) enriches the material during its growth. The microfluidic configuration of the pervaporation process is used to impose controlled growth along the channel thus enabling one to program spatial composition gradients using appropriate actuations of the valves. We demonstrate the possibilities offered by our technique through the fabrication of dense assemblies of nanoparticles and polymer composites with programmed gradients of fluorescent dyes. We also address the key issue of the spatial resolution of our gradients and we show that well-defined spatial modulations down to ≈50 μm can be obtained within colloidal materials, whereas gradients within polymer materials are resolved on length scales down to ≈1 mm due to molecular diffusion.

Shape-controlled synthesis of uniform noble metal nanoparticles (NPs) is crucial for the development of future plasmonic devices. The use of nanocrystals with well-defined morphologies and crystallinity as seed particles is expected to provide excellent shape control and monodispersity. We report the aqueous-based seed-mediated growth of monodisperse gold octahedra with wide range of sizes (50–150 nm in side length) by reducing different amounts of HAuCl4 on preformed single crystalline gold nanorods using butenoic acid as reducing agent. Butenoic acid plays a key role as a mild reducing agent as well as favoring the thermodynamic control of the reaction. The uniformity of the as-prepared Au octahedra combined with the use of a microfluidic technique based on microevaporation will allow the self-assembly of octahedra into uniform 3D supercrystals. Additionally, these plasmonic substrates exhibit high and uniform SERS signals over extended areas with intensities increasing with the Au nanoparticle size.

We investigated theoretically water evaporation from concentrated supramolecular mixtures, such as solutions of polymers or amphiphilic molecules, using numerical resolutions of a one dimensional model based on mass transport equations. Solvent evaporation leads to the formation of a concentrated solute layer at the drying interface, which slows down evaporation in a long-time scale regime. In this regime, often referred to as the falling rate period, evaporation is dominated by diffusive mass transport within the solution, as already known. However, we demonstrate that, in this regime, the rate of evaporation does not also depend on the ambient humidity for many molecular complex fluids. Using analytical solutions in some limiting cases, we first demonstrate that a sharp decrease of the water chemical activity at high solute concentration, leads to evaporation rates which depend weakly on the humidity, as the solute concentration at the drying interface slightly depends on the humidity. However, we also show that a strong decrease of the mutual diffusion coefficient of the solution enhances considerably this effect, leading to nearly independent evaporation rates over a wide range of humidity. The decrease of the mutual diffusion coefficient indeed induces strong concentration gradients at the drying interface, which shield the concentration profiles from humidity variations, except in a very thin region close to the drying interface., Comment: 13 pages, 10 figures

We present a microfluidic method leading to accurate measurements of the mutual diffusion coefficient of a liquid binary mixture over the whole solute concentration range in a single experiment. This method fully exploits solvent pervaporation through a poly(dimethylsiloxane) (PDMS) membrane to obtain a steady concentration gradient within a microfluidic channel. Our method is applicable for solutes which cannot permeate through PDMS, and requires the activity and the density over the full concentration range as input parameters. We demonstrate the accuracy of our methodology by measuring the mutual diffusion coefficient of the water (1) $+$ glycerol (2) mixture, from measurements of the concentration gradient using Raman confocal spectroscopy and the pervaporation-induced flow using particle tracking velocimetry., Comment: 9 pages, 8 figures

6 pages; International audience; This article reports a one-step approach for the fabrication of highly uniform, spherical Ag particles with tailored dimensions ranging from 10 to 30 nm. Coated with silica shell, the high uniformity of the particles allows their spontaneous assembly into millimeter-long extended 3-D arrays with transverse dimensions of tens of micrometers, using a microfluidic evaporation-based process.

International audience; We investigate flow coating processes, i.e., the formation of dry coatings starting from dilute complex fluids confined between a static blade and a moving substrate. In particular, we focus on the evaporative regime encountered at low substrate velocity, at which the coating flow is driven mainly by solvent evaporation in the liquid meniscus. In this regime, general arguments based on mass conservation show that the thickness of the dry film decreases as the substrate velocity increases, unlike the behavior in the well-known Landau–Levich regime. This work focuses on colloidal dispersions, which deserve special attention. Indeed, flow coating is expected to draw first a solvent-saturated film of densely packed colloids, which further dries fully when air invades the pores of the solid film. We first develop a model based on the transport equations for binary mixtures, which can describe this phenomenon continuously, using appropriate boundary conditions and a criterion to take into account pore-emptying in the colloidal film. Extensive numerical simulations of the model then demonstrate two regimes for the deposit thickness as a function of the process parameters (substrate velocity, evaporation rate, bulk concentration, and particle size). We finally derive an analytical model based on simplified transport equations that can reproduce the output of our numerical simulations very well. This model can predict analytically the two observed asymptotic regimes and therefore unifies the models recently reported in the literature.

We performed a thorough investigation of the drying dynamics of a charged colloidal dispersion drop in a confined geometry. We developed an original methodology based on Raman micro-spectroscopy to measure spatially-resolved colloids concentration profiles during the drying of the drop. These measurements lead, for the first time, to estimates of the collective diffusion coefficient of the dispersion over a wide range of concentration. The collective diffusion coefficient is one order of magnitude higher than the Stokes-Einstein estimate showing the importance of the electrostatic interactions for the relaxation of concentration gradients. At the same time, we also performed fluorescence imaging of tracers embedded within the dispersion during the drying of the drop, which reveals two distinct regimes. At early stages, concentration gradients along the drop lead to buoyancy-induced flows. Strikingly, these flows do not influence the colloidal concentration gradients that generate them, as the mass transport remains dominated by diffusion. At longer time scales, the tracers trajectories reveal the formation of a gel which dries quasi homogeneously. For such a gel, we show using linear poro-elastic modeling, that the drying dynamics is still described by the same transport equations as for the liquid dispersion. However, the collective diffusion coefficient follows a modified generalized Stokes-Einstein relation, as also demonstrated in the context of unidirectional consolidation by Style et al. [Crust formation in drying colloidal suspensions, Style et al., Proc. R. Soc. A 467, 174 (2011)]., Comment: 11 pages, 7 figures

A porous filter is fabricated directly inside a microfluidic circuit using a photoreticulable hydrogel. The filter could be used for separation of cells from blood, removal of particles or solutes, such as proteins, in microdialysis and microfiltering. The filter is realized by in situ polymerization approach: a liquid hydrogel is injected in a microfluidic circuit channel where the filter is formed in a specific location by polymerization of UV light, focused by an optical microscope.

International audience; We report an extensive study of the concentration process of aqueous polymer solutions confined within microfluidic channels, owing to the pervaporation of water through the matrix of the chip. Concentration of polymer continuously increases up to the formation of a dense material which eventually invades the channel. This technology can be used to fabricate micro-composites of different shapes starting from dilute inks. We use both theory and screening experiments to show that the dynamics of growth can be predicted by simple conservation equations. More precisely, we establish a quantitative prediction of the growth dynamics taking into account deformations of the soft channels of the moulds, and the solvent chemical activity of the polymer solution. The present results based on general transport equations for binary mixtures provide direct guidance for the design of micro-fabricated materials considering their shape, dimensions, time scale of fabrication, and chemical composition. This quantitative framework is indeed essential to engineer integrated polymer-based micro-devices by using combined pervaporation and microfluidic moulding.

International audience; We present a full experimental characterization of isotropic artificial optical magnetism at visible frequencies produced by “raspberrylike” plasmonic nanoclusters synthesized by a bottom-up approach. Experimental measurements of extinction and light scattering associated with numerical simulations enable one to extract absolute values of the magnetic scattering cross section across the whole visible spectral range. The strength of the resonant magnetic response of a single magnetic nanocluster is illustrated as the effective magnetic permeability of a homogeneous sphere of identical volume.

Ce travail porte sur l'application de l'imagerie Raman confocale a l'etude des processus de diffusion et de reaction chimique sous ecoulement. L'imagerie Raman permet de mesurer simultanement les c...

5 pages; International audience; The interplay between plasmons and excitons in bulk metamaterials are investigated by performing spectroscopic studies, including variable angle pump-probe ellipsometry. Gain functionalized gold nanoparticles have been densely packed through a microfluidic chip, representing a scalable process towards bulk metamaterials based on self-assembly approach. Chromophores placed at the hearth of plasmonic subunits ensure exciton-plasmon coupling to convey excitation energy to the quasi-static electric field of the plasmon states. The overall complex polarizability of the system, probed by variable angle spectroscopic ellipsometry, shows a significant modification under optical excitation, as demonstrated by the behavior of the ellipsometric angles W and D as a function of suitable excitation fields. The plasmon resonances observed in densely packed gain functionalized core-shell gold nanoparticles represent a promising step to enable a wide range of electromagnetic properties and fascinating applications of plasmonic bulk systems for advanced optical materials.

International audience; We use evaporation within a microfluidic device to extract the solvent of a (possibly very dilute) dispersion of nanoparticles and concentrate the dispersion until a solid made of densely packed nanoparticles grows and totally invades the microfluidic geometry. The growth process can be rationalized as an interplay between evaporation-induced flow and kinetic and thermodynamic coefficients which are system-dependent; this yields limitations to the growth process illustrated here on two main cases: evaporation- and transport-limited growth. Importantly, we also quantify how colloidal stability may hinder the growth and show that care must be taken as to the composition of the initial dispersion, especially regarding traces of ionic species that can destabilize the suspension upon concentration. We define a stability chart, which, when fulfilled, permits us to grow and shape-up solids, including superlattices and extended and thick arrays of nanoparticles made of unary and binary dispersions, composites, and heterojunctions between distinct types of nanoparticles. In all cases, the geometry of the final solid is imparted by that of the microfluidic device.

6 pages; International audience; We present high refractive index optical metamaterials assembled via a microfluidic evaporation technique. This technique enables fabrication of truly three-dimensional bulk samples from a suspension of nanoparticles with a number of layers well in excess of 600, surpassing rival techniques by at least an order of magnitude. In addition to their large dimensions, the assembled metamaterials show a high degree of homogeneity and warrant an easy and rapid optical characterization using spectroscopic ellipsometry. We believe that the suggested inexpensive method considerably reduces the complexity in assembling optical metamaterials and opens new avenues in engineering bulk optical devices by choice of nanoparticle composition and geometry.

We evidence experimentally and theoretically that natural convection driven by solutal density differences in a molecular binary mixture can boost the transport of colloids. We demonstrate that such buoyancy-driven flows have a negligible influence on the gradients that generate them, for moderate Rayleigh numbers in a confined geometry. These flows therefore do not homogenize the binary mixture but can disperse very efficiently large solutes. We illustrate the relevance of such effects thanks to several original experiments: drying of confined droplets, microfluidic evaporation, and interdiffusion in microfluidic flows.

We present a model that describes the drying of solutions and colloidal dispersions from droplets confined between two circular plates. This confined geometry, proposed by Cl\'ement and Leng [Langmuir 20, 6538 (2004)], casts a perfect control of the evaporation conditions, and thus also of the concentration kinetics of the solutes in the droplet. Our model, based on simple transport equations for binary mixtures, describes the concentration process of the solute inside the droplet. Using dimensionless units, we identify the different numbers that govern the concentration field of the solute, and we detail how to extract kinetic and thermodynamic information on the binary mixture from such drying experiments. We finally discuss, using numerical resolution of the model and analytical arguments, several specific cases: dilute solutions, a colloidal hard sphere dispersion, and a binary molecular mixture.

The flow curve of wormlike micelles usually exhibits a stress plateau σ* separating high and low viscosity branches, leading to shear‐banded flows. We study the flow of semidilute wormlike micellar systems in a confined geometry: a straight microchannel. We characterize their local rheology thanks to particle image velocimetry. We show that flow curves cannot be described by a simple constitutive equation linking the local shear stress to the local shear rate. We demonstrate the existence of nonlocal effects in the flow of wormlike micellar systems and make use of a theoretical framework allowing the measurement of correlation lengths.

This work describes the fabrication of thin microfluidic devices in Kapton (polyimide). These chips are well-suited to perform X-ray scattering experiments using intense microfocussed beams, as Kapton is both relatively resistant to the high intensities generated by a synchrotron, and almost transparent to X-rays. We show networks of microchannels obtained using laser ablation of Kapton films, and we also present a simple way to perform fusion bonding between two Kapton films. The possibilities offered using such devices are illustrated with X-ray scattering experiments. These experiments demonstrate that structural measurements in the 1 A–20 nm range can be obtained with spatial resolutions of a few microns in a microchannel.

Using Dynamic Light Scattering in heterodyne mode, we measure velocity profiles in a much studied system of wormlike micelles (CPCl/NaSal) known to exhibit both shear-banding and stress plateau behavior. Our data provide evidence for the simplest shear-banding scenario, according to which the effective viscosity drop in the system is due to the nucleation and growth of a highly sheared band in the gap, whose thickness linearly increases with the imposed shear rate. We discuss various details of the velocity profiles in all the regions of the flow curve and emphasize on the complex, non-Newtonian nature of the flow in the highly sheared band., 4 pages, 5 figures, submitted to Phys. Rev. Lett

Experimental observations of droplet size sustained oscillations are reported in a two-phase flow between a lamellar and a sponge phase. Under shear flow, this system presents two different steady states made of monodisperse multilamellar droplets, separated by a shear-thinning transition. At low and high shear rates, the droplet size results from a balance between surface tension and viscous stress, whereas for intermediate shear rates it becomes a periodic function of time. A possible mechanism for such kinds of oscillations is discussed.

We present local velocity measurements in emulsions under shear using heterodyne Dynamic Light Scattering. Two emulsions are studied: a dilute system of volume fraction $\phi=20$ % and a concentrated system with $\phi=75$ %. Velocity profiles in both systems clearly show the presence of wall slip. We investigate the evolution of slip velocities as a function of shear stress and discuss the validity of the corrections for wall slip classically used in rheology. Focussing on the bulk flow, we show that the dilute system is Newtonian and that the concentrated emulsion is shear-thinning. In the latter case, the curvature of the velocity profiles is compatible with a shear-thinning exponent of 0.4 consistent with global rheological data. However, even if individual profiles can be accounted for by a power-law fluid (with or without a yield stress), we could not find a fixed set of parameters that would fit the whole range of applied shear rates. Our data thus raise the question of the definition of a global flow curve for such a concentrated system. These results show that local measurements are a crucial complement to standard rheological tools. They are discussed in light of recent works on soft glassy materials., Comment: 13 pages, 21 figures, submitted to Eur. Phys. J. E

We engineered specific microfluidic devices based on the pervaporation of water through a PDMS membrane, to formulate continuous and steady concentration gradients of a binary aqueous molecular mixture at the nanolitre scale. In the case of a model complex fluid (a triblock copolymer solution), we demonstrate that such a steady gradient crosses the phase diagram from pure water up to a succession of highly viscous mesophases. We then performed in situ spatially resolved measurements (confocal spectroscopy and small-angle X-ray scattering) to quantitatively measure the concentration profile and to determine the microstructure of the different textures. Within a single microfluidic channel, we thus screen quantitatively and continuously the phase diagram of a complex fluid. Beside, as such a gradient corresponds to an out-of-equilibrium regime, we also extract from the concentration measurement a precise estimate of the collective diffusion coefficient of the mixture as a function of the concentration. In the present case of the triblock copolymer, this transport coefficient features discontinuities at some phase boundaries, which have never been observed before.

A tube-in-square-pipe microfluidic glass cell has been developed for studying the aggregation and fiber formation from regenerated silk solution by in-situ small-angle X-ray scattering using synchrotron radiation. Acidification-induced aggregation has been observed close to the mixing point of the fibroin and buffer solution. The fibrous, amorphous material is collected in a water bath. Micro-wide-angle X-ray scattering of the dried material confirms its beta-sheet nature.

Using velocity profile measurements based on dynamic light scattering and coupled to structural and rheological measurements in a Couette cell, we present evidences for a shear-banding scenario in the shear flow of the onion texture of a lyotropic lamellar phase. Time-averaged measurements clearly show the presence of structural shear-banding in the vicinity of a shear-induced transition, associated to the nucleation and growth of a highly sheared band in the flow. Our experiments also reveal the presence of slip at the walls of the Couette cell. Using a simple mechanical approach, we demonstrate that our data confirms the classical assumption of the shear-banding picture, in which the interface between bands lies at a given stress $\sigma^\star$. We also outline the presence of large temporal fluctuations of the flow field, which are the subject of the second part of this paper [Salmon {\it et al.}, submitted to Phys. Rev. E].