Search

Improvements in solar-to-thermal energy conversion will accelerate the development of efficient concentrated solar power systems. Nanofluid volumetric receivers, where nanoparticles in a liquid medium directly absorb solar radiation, promise increased performance over surface receivers by minimizing temperature differences between the absorber and the fluid, which consequently reduces emissive losses. We present a combined modeling and experimental study to optimize the efficiency of liquid-based solar receivers seeded with carbon-coated absorbing nanoparticles. A one-dimensional transient heat transfer model was developed to investigate the effect of solar concentration, nanofluid height, and optical thickness on receiver performance. Simultaneously, we experimentally investigated a cylindrical nanofluid volumetric receiver, and showed good agreement with the model for varying optical thicknesses of the nanofluid. Based on the model, the efficiency of nanofluid volumetric receivers increases with increasing solar concentration and nanofluid height. Receiver-side efficiencies are predicted to exceed 35% when nanofluid volumetric receivers are coupled to a power cycle and optimized with respect to the optical thickness and solar exposure time. This work provides insights as to how nanofluids can be best utilized as volumetric receivers in solar applications, such as receivers with integrated storage for beam-down CSP and future high concentration solar thermal energy conversion systems., MIT Energy Initiative, National Science Foundation (U.S.)

The choice of heat transfer fluids has significant effects on the performance, cost, and reliability of solar thermal systems. In this chapter, we evaluate existing heat transfer fluids such as oils and molten salts based on a new figure of merit capturing the combined effects of thermal storage capacity, convective heat transfer characteristics, and hydraulic performance of the fluids. Thermal stability, freezing point, and safety issues are also discussed. Through a comparative analysis, we examine alternative options for solar thermal heat transfer fluids including water−steam mixtures (direct steam), ionic liquids/melts, and suspensions of nanoparticles (nanofluids), focusing on the benefits and technical challenges., Center for Clean Water and Clean Energy at MIT and KFUPM (Project 6918351), United States. Dept. of Energy. Office of Science (Solid-State Solar-Thermal Energy Conversion Center Award DE-SC0001299)

To bridge the gap between theoretically predicted and experimentally demonstrated efficiencies of solar thermophotovoltaics (STPVs), we consider the impact of spectral non-idealities on the efficiency and the optimal design of STPVs over a range of PV bandgaps (0.45-0.80 eV) and optical concentrations (1-3,000x). On the emitter side, we show that suppressing or recycling sub-bandgap radiation is critical. On the absorber side, the relative importance of high solar absorptance versus low thermal emittance depends on the energy balance. Both results are well-described using dimensionless parameters weighting the relative power density above and below the cutoff wavelength. This framework can be used as a guide for materials selection and targeted spectral engineering in STPVs., United States. Dept. of Energy. Office of Basic Energy Sciences (DE-FG02-09ER46577)

Phase change material (PCM) suspensions have received wide spread attention for increased thermal storage in various thermal systems such as heat sinks for electronics and solar thermal applications. To achieve further heat transfer enhancement, this paper investigates the effect of focusing micron-sized phase-change particles (PCMs) to a layer near the heated wall of a parallel plate channel. A numerical model for fully-developed laminar flow with a constant heat flux applied to one wall is developed. Melting of the focused PCMs is incorporated using a temperature-dependent effective heat capacity. The effect of channel height, height of the focused PCM stream, heat flux, and fluid properties on the peak local Nusselt number ( Nu ∗ ) and the averaged Nusselt number over the melting length ( Nu melt ) are investigated. Compared to the thermally-developed Nusselt number for this geometry ( Nu o = 5.385), Nu melt and Nu ∗ enhancements of 8% and 19% were determined, respectively. The local heat transfer performance is optimized when the PCMs are confined to within 30% of the channel height. The present work provides an extended understanding of local heat transfer characteristics during melting of flowing PCM suspensions, and offers a new method for enhancing heat transfer performance in various thermal-fluidic systems.