Search

Ammonia and hydrogen are promoted as potential energy carriers for centralized energy restitution. This article investigates ammonia/hydrogen/air premixed turbulent combustion, using Large-Eddy Simulations, in an academic atmospheric gas turbine swirled burner. A one-dimensional flame analysis demonstrates the existence of a trade-off in NOX and NH3 emissions for ammonia/hydrogen blends, and the possibility to obtain 1D flame propagation characteristics close to that of a lean methane flame by adjusting the amount of H2. Large-Eddy Simulations of the PRECCINSTA burner exhibit stable combustion, while the optimized trade-off equivalence ratio is pinpointed at φ=1.46 for XH2Fuel=0.46. Corresponding emissions are XNOX≈XNH3≈300 ppmv. Large amounts of hydrogen are found in the exhaust gases, inducing a low combustion efficiency. The flame structure, combustion dynamics, influence of kinetics modelling and mesh resolution are discussed. This work paves the way for future studies, in the perspective of applications to industrial systems., SCOPUS: ar.j, info:eu-repo/semantics/published

Paper is a complex material consisting of a network of cellulose fibres at the micro-level. During manufacturing, the network is dried under restraint conditions due to tension in the paper web in machine direction. This gives rise to internal strains that are stored in the produced sheet. Upon exposure to a moisture cycle, these strains may be released. This results in permanent shrinkage that may cause instabilities such as curl or waviness of the sheet. The prime objective of this paper is to model this irreversible shrinkage and to link its magnitude to the properties of the fibres and of the network. For this purpose, randomly generated fibrous networks of different coverages (i.e. ratio of the area occupied by fibres and that of the sheet) are modeled by means of a periodic representative volume element (RVE). Within such RVEs, a finite element method combined with a kinematic hardening plasticity model at the scale of the fibres is used to capture the irreversible response. The computational results obtained demonstrate that the magnitude of the irreversible strains increases with coverage until a certain coverage and beyond that coverage decreases in magnitude. This phenomenon is explained by considering the area fraction of free-standing fibre segments relative to bonded fibre segments in the network. A structure–property dependency of irreversible strains at the sheet-level on the micro-structural parameters of the network is thereby established., SCOPUS: ar.j, info:eu-repo/semantics/published

In adsorption based separation techniques or in environmental applications where adsorption on a porous matrix is involved, the broadening of migrating bands of solutes varies with the characteristics of the adsorption isotherms and is generally overwhelming at solute concentrations deep in the non-linear region. We introduce here a novel concept to minimize concentration overloading dispersion: We show theoretically that a spatial alternation of Langmuir (L) and Anti-Langmuir (AL) zones along the displacement direction induces an accordion effect, i.e. an alternation of sharpening and dilution of the solute zones, reducing in the end the final broadening of the peak. We quantify in the parameter space of the problem the reduction in concentration overloading related band widening of the L-AL system compared to the pure L or AL cases. A numerical analysis of the solute transport reveals a dependence of solute spreading on the ratio of sample to stationary phase zone widths and on the intensity of the adsorption parameter. The initial position of the sample solvent in its surrounding liquid i.e. whether the displacement starts in a L or AL zone is also shown to have an influence on the dispersive behavior. An analysis is performed to highlight the optimal alternance geometry to minimize solute spreading., SCOPUS: ar.j, info:eu-repo/semantics/published

The Zinc level in many 6000 Al alloys (Al-Mg-Si-type) was set to a maximum of 0.03 wt% as common industrial practice. Concentrations above 0.03 wt% can modify the alkaline etching mechanism causing the surface to go from a desired smooth look associated with a grain boundary attack (GBA), into an undesired speckled appearance due to preferential grain etching (PGE), visible after anodizing. This significantly limits the ambition of reducing the carbon footprint of Aluminum by increasing the amount of recycled material in the production process. Because Cu has been reported to counteract this negative effect of Zn, the present study is dedicated to contribute to the understanding of this interaction and is focused on Zn and Cu in peak aged AlMgSi alloys. The chemical composition of the various precipitates formed in two Al6063 alloys was studied by means of TEM and EDX, whereby Zn was found in the Q phase (AlMgSiCu) grain boundary precipitates. Two alloys, with different content of Cu and Zn were studied. The Zn/Cu ratio in the bulk was similar for both alloys, but the level of Zn in the Cu containing Q particles in the grain boundaries was different. The increased Zn concentration in Q phase precipitates is believed to decrease the potential of the precipitates with respect to the surrounding matrix. Thus, the Cu/Zn ratio in these alloys is extremely important as it defines the potential differences that in turn cause either GBA or PGE., SCOPUS: ar.j, info:eu-repo/semantics/published

Silicon is an essential alloying element added in quenching and partitioning (Q&P) steels to delay and/or suppress carbide precipitation. However, there is a strong industrial interest to reduce the silicon content as it has detrimental effects on the metallurgical route. This work investigates by means of in situ high-energy XRD (HEXRD) the effect of silicon on the microstructural evolution during quenching and partitioning of a commercial 0.2C-2.3Mn grade. The results of this study highlight the role of the bainite transformation during the reheating and partitioning steps for effective austenite retention. Silicon influences the kinetics of austenite decomposition into bainite and finally promotes the stabilization of austenite. This is explained by the ability of silicon to suppress carbide precipitation (i) at the interface between bainite and austenite and (ii) in the martensite matrix. Carbide precipitation at the bainite/austenite interface decreases the amount of carbon that diffuses from bainite to austenite, subsequently accelerating the bainite transformation kinetics and preventing austenite stabilization. Carbide precipitation in martensite reduces the amount of carbon available for partitioning in austenite, further preventing its stabilization. Additions of elements such as Cr or Mo could be therefore considered in order to reduce the austenite decomposition in low-silicon steel grades., SCOPUS: ar.j, info:eu-repo/semantics/published

Duplex stainless steels (DSSs) are corrosion-resistant alloys extensively used in aggressive environments. Cast DSSs may be selected for pipes, valves and pumps in chemical, petrochemical and nuclear industries. The grade steel ASTM A890 1B is an example of cast DSS with 2.7-3.3%Cu addition. Copper increases the resistance to many types of corrosion, especially in non-oxidizing environments. When the copper content is higher than 2%, the steel can be precipitation-hardened. In this work, the precipitation hardening of a DSS ASTM A890 1B steel with 3.0%Cu was studied and modeled for aging temperatures in the 450-600 °C range. Copper precipitates in the ferrite phase, but remains in solid solution in the austenite. The age hardening curves were modeled by ΔH = K(t) n model, where ΔH is the increase in hardness, t is the aging time, and K and n are constants to be determined. The microstructure and substructure were investigated by scanning electron and transmission electron microscopes., SCOPUS: ar.j, info:eu-repo/semantics/published

In the presence of temperature gradients along the gas-liquid interface, a liquid bridge is prone to hydrothermal instabilities. In the case of a coaxial gas stream, in addition to buoyancy and thermocapillary forces, the shear stresses and interfacial heat transfer affect the development of these instabilities. By combining experimental data with three-dimensional numerical simulations, we examine the evolution of hydrothermal waves in a liquid bridge with with a gas flow parallel to the interface. The gas moves from the cold to the hot side with a constant velocity of and its temperature is the main control parameter of the study. When the thermal stress exceeds a critical value, a three-dimensional oscillatory flow occurs in the system. A stability window of steady flow has been found to exist in the map of dynamical states in terms of gas temperature and applied thermal stress. The study is carried out by tracking the evolution of hydrothermal waves with increasing gas temperature along three distinct paths with constant values of: Path 1 is selected to be just above the threshold of instability while path 2 traverses the stability window and path 3 lies above it. We observe a variety of dynamics including standing and travelling waves, determine their dominant and secondary azimuthal wavenumbers, and suggest the mathematical equations describing hydrothermal waves. Multimodal standing waves, coexistence of travelling waves with several wavenumbers rotating in the same or opposite directions are among the most intriguing observations., SCOPUS: ar.j, info:eu-repo/semantics/published

Dip coating is a common technique used to cover a solid surface with a thin liquid film, the thickness of which was successfully predicted by the theory developed in the 1940s by Landau & Levich (Acta Physicochem. URSS, vol. 17, 1942, pp. 141-153) and Derjaguin (Acta Physicochem. URSS, vol. 20, 1943, pp. 349-352). In this work, we present an extension of their theory to the case where the dipping bath contains two immiscible liquids, one lighter than the other, resulting in the entrainment of two thin films on the substrate. We report how the thicknesses of the coated films depend on the capillary number, on the ratios of the properties of the two liquids and on the relative thickness of the upper fluid layer in the bath. We also show that the liquid/liquid and liquid/gas interfaces evolve independently from each other as if only one liquid were coated, except for a very small region where their separation falls quickly to its asymptotic value and the shear stresses at the two interfaces peak. Interestingly, we find that the final coated thicknesses are determined by the values of these maximum shear stresses., SCOPUS: ar.j, info:eu-repo/semantics/published

Thermodiffusion, which leads to a component separation in a mixture due to the thermal gradient, still does not have an unambiguous microscopic picture. Therefore, experimental studies, especially in convection free environment, are important. As part of the 4th campaign on the DCMIX project, thermodiffusion experiments on three compositions of the toluene-methanol-cyclohexane ternary mixture, on a mixture of fullerene-tetralin-toluene and on a mixture of polystyrene-toluene-cyclohexane have been performed in microgravity conditions on board the International Space Station. A binary mixture of polystyrene-toluene has been filled into the companion cell for the campaign. The Selectable Optical Diagnostics Instrument (SODI), wich is a two-wavelength Mach-Zehnder interferometer for the ternary mixtures, plus a monochromatic Mach-Zehnder interferometer for the binary mixture, has been used in order to obtain the temperature and the concentration fields in the cells. Precisely, it is a 5-steps phase-shifting interferometry technique which is implemented with SODI, producing by means of laser illumination a set of 5 phase-shifted images of π/2 between them as function of the time. A total of 58 runs of various durations and at different mean temperatures have been conducted. Here, we evaluate the contrast of the interferograms, the quality in the phase stepping, the stability of the thermal regulation of the experiments and the level of environmental disturbances on board the space station during the campaign., SCOPUS: ar.j, info:eu-repo/semantics/published

When a liquid drop is placed on a highly superheated surface, it can be levitated by its own vapour. This remarkable phenomenon is referred to as the Leidenfrost effect. The thermally insulating vapour film results in a severe reduction of the heat transfer rate compared to experiments at lower surface temperatures, where the drop is in direct contact with the solid surface. A commonly made assumption is that this solid surface is isothermal, which is at least questionable for materials of low thermal conductivity, resulting in an overestimation of the surface temperature and heat transfer for such systems. Here we aim to obtain more quantitative insight into how surface cooling affects the Leidenfrost effect. We develop a technique based on Mach-Zehnder interferometry to investigate the surface cooling of a quartz plate by a Leidenfrost drop. The three-dimensional plate temperature field is reconstructed from interferometric data by an Abel inversion method using a basis function expansion of the underlying temperature field. By this method we are able to quantitatively measure the local cooling inside the plate, which can be as strong as 80 K. We develop a numerical model which shows good agreement with experiments and enables extending the analysis beyond the experimental parameter space. Based on the numerical and experimental results we quantify the effect of surface cooling on the Leidenfrost phenomenon. By focusing on the role of the solid surface we provide new insights into the Leidenfrost effect and demonstrate how to adjust current models to account for non-isothermal solids and use previously obtained isothermal scaling laws for the neck thickness and evaporation rate., SCOPUS: ar.j, info:eu-repo/semantics/published

The jet wiping process is a cost-effective coating technique that uses impinging gas jets to control the thickness of a liquid layer dragged along a moving strip. This process is fundamental in various coating industries (mainly in hot-dip galvanizing) and is characterized by an unstable interaction between the gas jet and the liquid film that results in wavy final coating films. To understand the dynamics of the wave formation, we extend classic laminar boundary layer models for falling films to the jet wiping problem, including the self-similar integral boundary layer and the weighted integral boundary layer models. Moreover, we propose a transition and turbulence model to explore modelling extensions to larger Reynolds numbers and to analyse the impact of the modelling strategy on the liquid film dynamics. The validity of the long-wave formulation was first analysed on a simpler problem, consisting of a liquid film falling over an upward-moving wall, using volume of fluid simulations. This validation proved the robustness of the integral formulation in conditions that are well outside their theoretical limits of validity. Finally, the three models were used to study the response of the liquid coat to harmonic and non-harmonic oscillations and pulsations in the impinging jet. The impact of these disturbances on the average coating thickness and wave amplitude is analysed, and the range of dimensionless frequencies yielding maximum disturbance amplification is presented., SCOPUS: ar.j, info:eu-repo/semantics/published

A γ–irradiated bovine albumin serum-based nanoparticle was characterised structurally, and functionally. The nanoparticle was characterised by A.F.M. D.L.S, zeta potential, T.E.M. gel-electrophoresis, and spectroscopy. We studied the stability of the nanoparticle at different pH values and against time, by fluorescence spectroscopy following the changes in the tryptophan environment in the nanoparticle. The nanoparticle was also functionalized with Folic Acid, its function as a nanovehicle was evaluated through its interaction with the hydrophobic drug Emodin. The binding and kinetic properties of the obtained complex were evaluated by biophysical methods as well as its toxicity in tumor cells. According to its biophysics, the nanoparticle is a spherical nanosized vehicle with a hydrodynamic diameter of 70 nm. Data obtained describe the nanoparticle as nontoxic for cancer cell lines. When combined with Emodin, the nanoparticle proved to be more active on MCF-7 cancer cell lines than the nanoparticle without Emodin. Significantly, the albumin aggregate preserves the main activity-function of albumin and improved characteristics as an excellent carrier of molecules. More than carrier properties, the nanoparticle alone induced an immune response in macrophages which may be advantageous in vaccine and cancer therapy formulation., SCOPUS: ar.j, info:eu-repo/semantics/published

A low Young's modulus is required for titanium alloys used in orthopedic implants, such as hip prosthetic stems, in order to avoid stress shielding due to a large difference in Young's modulus between the prosthetic stem and the cortical bone. The low Young's modulus has been observed to occur in metastable β-Ti alloys by precipitation of a stress-induced α″ martensite during cold deformation. Under this context, the Influence of thermo-mechanical processing on the microstructure and mechanical properties of the metastable β Ti–29Nb–2Mo–6Zr alloy was studied as well as the influence of the degree of deformation by cold rolling with subsequent annealing after homogenization heat treatment. The alloy presents a β microstructure after solution heat treatment at 1000 °C for 24h, followed by water quenching, while posterior cold rolling induces the precipitation of α” martensite. Young's modulus decreases and hardness increases with the degree of deformation. The annealed samples showed higher hardness and Young's modulus than the cold rolled samples. A thickness reduction of 90% maximizes the hardness/Young's modulus ratio and optimizes the required mechanical properties for orthopedic implants. The results indicate that the alloy is a promising alternative for the widely used Ti–6Al–4V., SCOPUS: ar.j, info:eu-repo/semantics/published

A new concept of vapour condenser is proposed to solve the drainage problem and to provide an effective condensate flow under weightlessness conditions. The concept combines the capability of a curvilinear surface to drive liquid, and a combination of a porous media and a pump, as an active condensate retraction system. The porous media collects and stores the condensed fluid and acts as a barrier for the vapour phase. Hydrodynamic validation of the liquid flow was done against retraction overflow under terrestrial conditions. It was figured out that the time available for adjusting the retraction system to avoid film disturbances decreased non-linearly with an increase in retraction overflow. The behaviour of the proposed condenser with the retraction system was tested under weightlessness condition during the ESA parabolic flights campaign as a part of concept validation. Three porous media with different values of the pore size and material were tested. It was found that the combination of the pump and porous media helped to improve the condensate flow. It was observed that the stabilisation effect was influencing the condensate flow not only during weightlessness condition but also under acceleration disturbances during the campaign., SCOPUS: ar.j, info:eu-repo/semantics/published

We present a combined analytical approach and numerical study on the stability of a ring bound to an annular elastic substrate, which contains a circular cavity. The system is loaded by depressurizing the inner cavity. The ring is modeled as an Euler-Bernoulli beam and its equilibrium equations are derived from the mechanical energy which takes into account both stretching and bending contributions. The curvature of the substrate is considered explicitly to model the work done by its reaction force on the ring. We distinguish two different instabilities: periodic wrinkling of the ring or global buckling of the structure. Our model provides an expression for the critical pressure, as well as a phase diagram that rationalizes the transition between instability modes. Towards assessing the role of curvature, we compare our results for the critical stress and the wrinkling wavelength to their planar counterparts. We show that the critical stress is insensitive to the curvature of the substrate, while the wavelength is only affected due to the permissible discrete values of the azimuthal wavenumber imposed by the geometry of the problem. Throughout, we contrast our analytical predictions against finite element simulations., SCOPUS: ar.j, info:eu-repo/semantics/published

Injectable hydrogels have gained lots of attention as cell and growth factor carrier in tissue engineering. Here, we developed a novel graphene oxide (GO) reinforced poly(N-isoproplylacrylamide)/chitosan temperature-responsive (pNCG) hydrogel, and the gelation temperature was around 36.4 °C. Then, vascular endothelial cells (VECs) laden pNCG hydrogel was fabricated by encapsulating VECs through the sol–gel transfer process. Also, a sequential release system of monocyte chemoattractant protein-1 (MCP-1) and vascular endothelial growth factor (VEGF) was delicately designed and incorporated into VECs-laden pNCG hydrogel. In vitro and in vivo experiments confirmed that the VECs could proliferate into hydrogel, as well as feasible in-growing angiogenesis. Thus, the injectable pNCG hydrogel holds great potential for biomedical applications., SCOPUS: ar.j, info:eu-repo/semantics/published

Brush seals have been extensively studied for the last thirty years as an advanced sealing solution for gas turbine engines. The research is always aimed towards the reduction of the leakage flow, that has direct repercussions on the specific fuel consumption, the thrust-to-weight ratio, and the emission of pollutants. In addition, the sealing device must cope with side effects related to higher interface speeds, rotordynamics issues, or durability. Brush seals main assets are their excellent leakage performance with low friction properties compared to other contact seals like lip seals, and their ability to withstand rotor radial excursion without permanent damage. However, proper design optimization cannot be performed without the inclusion of the tribological performance. This paper presents a parametric investigation of the friction properties of carbon fibre brush seals as a function of the fibre pack geometry and the rotational speed. Carbon fibre and commonly used metallic brush seals present fundamentally different behaviour in presence of differential pressure or rotational speed. This paper also proposes an alternative method to predict the brush seal torque, based on measurements with a torque sensor. Heat generation was also evaluated with a thermographic camera. Both methods ensured consistency between results., SCOPUS: ar.j, info:eu-repo/semantics/published

We consider the response to periodic forcing between 5 Hz and 50 Hz of an interface separating immiscible fluids under the microgravity conditions of a parabolic flight. Two pairs of liquids with viscosity ratios differing by one order of magnitude are investigated. By combining experimental data with numerical simulations, we describe a variety of dynamics including harmonic and subharmonic (Faraday) waves, frozen waves and drop ejection, determining their thresholds and scaling properties when possible. Interaction between these various modes is facilitated in microgravity by the relative ease with which the interface can move, altering its orientation with respect to the forcing axis. The effects of key factors controlling pattern selection are analysed, including vibrational forcing, viscosity ratio, finite-size effects and residual gravity. Complex behaviour often arises with features on several spatial scales, such as Faraday waves excited on the interface of a larger columnar structure that develops due to the frozen wave instability - this type of state was previously seen in miscible fluid experiments but is described for the first time here in the immiscible case., SCOPUS: ar.j, info:eu-repo/semantics/published

Beam-column joints are critical component in the load path of reinforced concrete (RC) frames, due to their role in transferring loads among different RC frame components. The loss of a ground corner column in a RC frame turns an exterior joint into an inverted knee joint and recent code provisions for exterior joints are not sufficient to knee joints because of reinforcement defects in terms of joint vertical stirrups and improper column bar anchorage. This paper investigates numerically the behaviour of these joints under a closing moment using nonlinear finite element (FE) analysis with LS-DYNA. Beam’s bar anchorage type and joint vertical stirrups are the main parameters considered next to concrete compressive strength, longitudinal reinforcement ratio and lateral beam effect. This study indicates that, anchorage beam’s bar with U shaped produces better behaviour than 90° standard hooks or headed ends. Contribution of joint vertical stirrups is more influential with headed bars anchorage. Increasing concrete compressive strength and beam reinforcement ratio improve joint ultimate capacity. The presence of lateral beams reduces the rate of concrete degradation in the joint after reaching ultimate capacity and increases joint carrying capacity., SCOPUS: ar.j, info:eu-repo/semantics/published

Beta titanium alloys were developed for biomedical applications due to the combination of its mechanical properties including low elasticity modulus, high strength, fatigue resistance, good ductility and with excellent corrosion resistance. With this perspective a metastable beta titanium alloy Ti-12Mo-13Nb was developed with the replacement of both vanadium and aluminum from the traditional alloy Ti-6Al-4V. This paper presents the microstructure, mechanical properties of the Ti-12Mo-13Nb hot swaged and aged at 500 °C for 24 h under high vacuum and then water quenched. The alloy structure was characterized by X-ray diffraction and transmission electron microscopy. Tensile tests were carried out at room temperature. The results show a microstructure consisting of a fine dispersed α phase in a β matrix and good mechanical properties including low elastic modulus. The results indicate that Ti-12Mo-13Nb alloy can be a promising alternative for biomedical application., SCOPUS: cp.j, info:eu-repo/semantics/published

Metastable β-type Ti alloys with non-toxic addition elements such as Mo, Zr, Sn, Ta and Nb were developed as an alternative to the widely used Ti-6Al-4V alloy for biomedical applications. These alloys possess enhanced biocompatibility and reduced elastic modulus in comparison with Ti-6Al4V. Moreover, for orthopedic implants, low Young's modulus is required in order to avoid the stress shielding phenomenon. This study analyzes the microstructure and mechanical properties of a new Ti-12Mo-8Nb alloy after hot swaging, annealing at 950 ºC for 1h and water quenching. The alloy was characterized by X-ray diffraction, optical microscopy and transmission electron microscopy. Tensile tests were performed at room temperature. Young's modulus and hardness values were also measured. The structural characterization reveals a metastable β structure containing only a small amount of α and ω phases. Exhibiting a lower Young's modulus than Ti-6Al-4V and other previously studied Ti-Mo-Nb alloys, the Ti-12Mo-8Nb alloy can be a promising alternative for orthopedic application., SCOPUS: cp.j, info:eu-repo/semantics/published

Cd1-xZnxS thin films have been studied extensively as window layers for solar cell applications. However, a mismatch between the Cd1-xZnxS and copper-indium-gallium-selenide absorber layers increases with Zn film concentration, which reduces the device eficiency. In this work, Cd1-xZnxS thin films with low Zn concentrations were analyzed. The effect of the addition of different molar Zn concentrations to the reaction mixture on the growth mechanism of Cd1-xZnxS thin films and the influence of these mechanisms on structural, optical and morphological properties of the films has been studied. Cd1-xZnxS thin films were synthesized by chemical bath deposition using an ammonia-free alkaline solution. Microstructural analysis by X-ray diffraction showed that all deposited films grew with hexagonal structure and crystallite sizes decreased as the Zn concentration in the film increased. Optical measurements indicated a high optical transmission between 75% and 90% for wavelengths above the absorption edge. Band gap value increased from 2.48 eV to 2.62 eV, and the refractive index values for Cd1-xZnxS thin films decreased as the Zn increased. These changes in films and properties are related to a modification in growth mechanism of the Cd1-xZnxS thin films, with the influence of Zn(OH)2 formation being more important as Zn in solution increases., SCOPUS: ar.j, info:eu-repo/semantics/published

This paper is a review of the thermal stability of nanostructured nitride coatings synthesised by reactive magnetron sputtering technique. In the last three decade, nitride based coatings have been widely applied as hard wear-protective coatings in mechanical components. More recently, a larger interest has been addressed to evaluate the thermal stability of such coatings, as their mechanical and tribological properties are deteriorated at high working temperatures. This study describes the microstructural, mechanical and compositional stability of nanocrystalline Cr-N and nano-composited Ti-N based coatings (Ti-Al-Si-B-N and Ti-Cr-B-N) after air and vacuum annealing. For Cr-N coatings annealing in vacuum induces phase transformation from CrN to Cr 2N, while after annealing in air only Cr2O3 phase is present. For Ti-N based coatings, a well-definite multilayered structure was shown after air annealing. Degradation of mechanical properties was observed for all the nitride coatings after thermal annealing in air. © (2010) Trans Tech Publications., SCOPUS: ar.k, info:eu-repo/semantics/published

β-metastable titanium alloys with high strength to Young's modulus ratio have been developed by different authors aiming their use as biomaterials for hard tissue replacement. However, it is not easy to combine low elastic modulus with high mechanical strength. In this work, a β-Ti alloy (Ti-10Mo-20Nb) was produced by arc-melting, then homogenized, cold swaged and aged in order to obtain fine α-Ti precipitates in a β-Ti matrix. The microstructures were characterized by transmission electron microscopy and X-ray diffraction. Mechanical properties characterization was based on Vickers microhardness tests and Young's modulus measurements. The cold swaged material subjected to an ageing treatment at 500 °C for 4 h showed the highest hardness/Young's modulus ratio, associated to very fine α phase precipitates in a β-Ti matrix., SCOPUS: cp.j, info:eu-repo/semantics/published

Ti-doped carbon coatings were deposited on TiAlV alloys by reactive dc-magnetron sputtering in Ar/CH4 mixed gas. When Ar flow increases the incorporation of Ti into films raises while the concentration of C decreases. The formed nanometric TiC crystals were more noticeable for coatings deposited with higher Ar flows. Hardness (H) and elastic modulus (E) of coatings were measured by nanoindentation. H values were in the range of 8.8-15.9 GPa and E of 53.4-113.7 GPa. Higher values for H and E were obtained for films containing larger amount of TiC-phase. The presence of TiC crystals increased the coefficient of friction (COF) from 0.07 to 0.28 in scratch tests. Tribological experiments were carried out by using a pin-on-disk apparatus in air and in liquid. COF values ranged from 0.10 to 0.50 for tests in air. Despite of presenting higher COF, tests performed in liquid resulted in less pronounced wear tracks., SCOPUS: ar.j, info:eu-repo/semantics/published

A model is presented to describe the creep behaviour of glassy polymers below the glass transition temperature. It consists of a Hookean spring in series with a non-Newtonian dashpot having an entropy spring in parallel. The shape of the response of this spring is deduced from a master curve, giving the extension as a function of logarithm of time, built from creep data, reported here and obtained on polycarbonate over a wide range of times and temperatures. The model takes into account a number of aspects of creep behaviour and predicts a threshold stress beneath which delayed yielding no longer occurs. Torsional creep data, obtained on Polyvinylchloride by Mallon and Benham are found to be in excellent agreement with the proposed model. © 1975 Chapman and Hall Ltd., SCOPUS: ar.j, info:eu-repo/semantics/published

The tensile stress-strain curve of a glassy polymer is compared to the response of a rheological system including a generalized non-linear Maxwell model. The treatment assumes that throughout the course of deformation, some structure initially present in the polymer is destroyed and that the initial spectrum of the Maxwell elements is converted to another spectrum. A law of transformation of these spectra as a function of deformation is proposed while their expression is assumed to be analogous to that of the spectrum of a structureless material, experimentally determined. Data are found to be fully consistent with the proposed treatment. © 1978 Chapman and Hall Ltd., SCOPUS: ar.j, info:eu-repo/semantics/published

The compression yield behaviour of PMMA has been investigated, here, over a wide range of experimental conditions which cannot be reached in tensile tests owing to the brittle nature of the material. The plot of the ratio of the compression yield stress to absolute temperature, as a function of the logarithm of the strain-rate, gives a set of parallel curves which can be accurately superimposed by shifting along a slanting straight line. A master curve is built from which the yield behaviour may be predicted for any state of stress, or value of temperature and strain-rate in the glassy range, using Bauwens' yield criterion. The validity of the procedure is checked for compression tests at low temperatures, for tensile tests in the range of experimental conditions where PMMA yields and for torsional tests under hydrostatic pressure (data of Ward et al). In every case, the fit is found to be quite accurate. A region of experimental conditions is determined where the compression yield behaviour may not be described by the Ree-Eyring treatment involving a hyperbolic sine function. In this region, the Bauwens approach, which consists of a modification of the Ree-Eyring theory, taking into account a distribution of relaxation times and linking the yield behaviour with the β mechanical loss peak, is found to give an acceptable fit to the data. © 1973 Chapman and Hall Ltd., SCOPUS: ar.j, info:eu-repo/semantics/published

The dilution is an event that have a high influence on the microstructure and, consequently, in the properties of weld claddings. The present study evaluated the effect of dilution level on the microstructure of the fusion zone of alloy Inconel 686 weld claddings. The claddings were welded by the TIG cold wire feed process. The dilution was calculated from the geometric characteristics and based on chemical composition of the materials obtained by energy dispersive X-ray spectroscopy and optical emission spectroscopy. The microstructure of all claddings were composed by a γ-FCC matrix with some minor precipitates. These particles are called in literature as topologically closed-packed phases (TCP). These precipitates assumed several morphological aspects, being the shapeless morphology observed in more frequency in all claddings evaluated, independent of dilution level. A phase with lamellar morphology, which growth establishing an orientation relationship with the γ-FCC matrix solidification direction, was observed only in claddings with a low dilution level. In addition, a shapeless phase with a fine precipitation aggregated was observed in claddings with a high dilution level., SCOPUS: ar.j, info:eu-repo/semantics/published

The viscoelastic behaviour of three different samples of polycarbonate, with differing pre-treatment, is described here by a generalized non-linear Maxwell system, proposed previously. This model gives the variation of the tensile yield stress related to each sample as a function of temperature and strain rate. The response is checked over a large range of strain rates, at temperatures from 20 to 80° C. The model allows the determination of the damping peak arising from the molecular movements which it expresses. A correspondence is found with the intermediate loss peak location, which occurs for each sample just below the α transition. Results obtained from dynamic mechanical tests and differential scanning calorimetry show that the structure of the samples changes in the range of temperatures where the intermediate loss peak arises at 1 Hz. © 1979 Chapman and Hall Ltd., SCOPUS: ar.j, info:eu-repo/semantics/published

A steady-state technique of heat-transfer measurement has been developed based on the method of Seban, Emery & Levy (1959) whereby energy is dissipated by the Joule effect in a thin metal sheet on the surface of a model. For the present application, use was made of very thin but mechanically resistant films of metal of very nearly constant thickness, obtained by a simple mirror-silvering technique. The present investigation was prompted by the desire to make very local measurements of heat transfer for application in regions where large variations in convective heat flux and therefore in temperature could be expected. Comparison between theory and experiment has been made in the simple case of a flat plate with constant heat flux for which a rigorous computation could be made based on the theory of Chapman & Rubesin (1949). The model was so conceived that the heat losses were small enough to be neglected. Therefore no corrections, which are often inaccurate, were needed for the experimental results, contrary to what is generally done when using other techniques for heat-transfer measurements. The excellent agreement between theory and experiment gives complete confidence in the method. The theoretical analysis showed that the measurements are simply related to the results that could be obtained in the case of an isothermal surface, because of the constant ratio that exists between the corresponding heat-transfer coefficients. © 1964, Cambridge University Press. All rights reserved., SCOPUS: ar.j, info:eu-repo/semantics/published

The compression yield behaviour of polycarbonate, at constant strain-rate, over a wide range of temperatures, is described by the Ree-Eyring theory of non-Newtonian viscosity linked with a treatment which takes into account a distribution function of activation energies. The proposed yield mechanism relies on the assumption that the β process considered in the Ree-Eyring theory and the loss peak revealed by oscillatory measurements are related to the same molecular movements. A relation is given between the β transition conditions in yield measurements and in damping tests; its validity is checked. The broadness and the shape of the β loss peak are correlated with a spectrum of activation energies. The compression yield-stress curve, giving the yield stress versus temperature at constant strain-rate, is computed from the measurements of the loss tangent, as a function of temperature, at the frequency corresponding to the strain-rate and is found to fit the data fairly well. © 1972 Chapman and Hall Ltd., SCOPUS: ar.j, info:eu-repo/semantics/published

A method of preparation of “mischmetall” by thermal reduction of mixed fluorides of rare earth metals, using calcium as reducing agent, has been submitted to an experimental investigation. Raw materials were ores from the Belgian Congo from which, by using well-known chemical methods, mixed oxides of rare earth were extracted. The preparation of the mixed fluorides was carried out in two steps. First, double fluorides of rare earth and ammonium were produced by reaction of the mixed oxides with ammonium bifluoride; then the double fluorides were decomposed by heating; ammonium fluoride being volatilized, the mixed fluorides can be easily recovered. The mixed fluorides were submitted to thermal reduction with calcium with addition of a small amount of iodine. The reaction is self-supporting and small ingots of mischmetall were obtained with a fairly good efficiency. © 1953, The Electrochemical Society, Inc. All rights reserved., SCOPUS: ar.j, info:eu-repo/semantics/published

Simulations of atmospheric entry of spacecraft and satellites require accurate knowledge of thermo-physical properties such as heat capacity in a wide temperature range. However, the characterization of this quantity is not straightforward for carbon composites at high temperatures, due to pyrolysis reactions that occur in the material. We develop a methodology for determining the heat capacity and required heat of pyrolysis for carbon composites in these conditions. The methodology consists of three steps: organic elemental analysis to determine composition, differential scanning calorimetry experiments on the different components to determine apparent heat capacity, and computations to separate the apparent heat capacity into heat capacity and heat of pyrolysis. This methodology is applied to the ZURAM® carbon/phenolic ablator from room temperature up to 1100 K. The results obtained were compared to separate analyzes of the different components of the material, assuming that heat capacity is an additive property. It was found that compressing the samples into disks provides improved resolution and repeatability for low density materials. This provided a determination of the heat capacity of the decomposing composite with a relative standard deviation, SCOPUS: ar.j, info:eu-repo/semantics/published