Search

A zero-current switching full-bridge isolated dc/dc converter based on a semiresonant L-C cell has been developed in this paper. With respect to the classical full-bridge configuration, no additional switches are required, thus by preserving its simplicity and robustness. The proposed architecture allows achieving zero-current switching at both primary and secondary sides. A 50-kW prototype has been developed and tested in different operating conditions. The experimental results are in agreement with the simulations by confirming the goodness of the proposed solution. Efficiency up to 97% at full load operating condition has been reached in the laboratory prototype. [ABSTRACT FROM PUBLISHER]

In this paper, the use of the Dual Kalman Filter for the identification of photovoltaic system parameters is presented. The system includes the photovoltaic source, the dc/dc converter and the battery/dc bus and both its states and parameters in the actual operating conditions are identified. In particular, the proposed approach gives the confidence interval for the system settling time, which is used for the real-time optimization of the perturbative maximum power point tracking algorithm. The proposed technique is implemented by using a Field-Programmable Gate Array and it is validated by means of both simulation and experimental results. [ABSTRACT FROM PUBLISHER]

The long power production warranties guaranteed by the manufacturers of photovoltaic (PV) modules (25 years) are a vital factor for the economical viability of PV systems. Nevertheless, recent studies have demonstrated that the modules may experience an early degradation, which turns into the reduction of the power production or even the damage of the entire PV module. In this paper, a method aimed at detecting the module degradation is introduced. It detects and quantifies the degradation by means of two indicators, which are aimed at estimating the increment of the modules series resistance, this parameter being one of the most affected by some degradation mechanisms. The increase of the series resistance value is estimated through the evaluation of the error in predicting the position of the maximum power point, which is obtained by comparing the experimental measurements with the single-diode model. The proposed method is experimentally validated, and it is compared with other methods reported in the literature. The results show that the proposed indicators are able to accurately estimate the increments of the series resistance with a low sensitivity to the irradiance and temperature values. This feature improves the accuracy and the reliability of the diagnosis processes and monitoring systems. [ABSTRACT FROM PUBLISHER]

The maximum power point (MPP) tracking function allows one to extract the maximum power from the photovoltaic (PV) system in any operating condition. The perturb and observe technique is one of the mainly used algorithms aimed at this function. Its performances depend on the values of the two design parameters, which are the amplitude and the frequency of the perturbations that it applies in identifying the position of the MPP. In this paper, a method for the online optimization of the perturbation period is presented. It is based on the identification of the whole system, including the PV source and the dc/dc converter controlling it. The system impulse and frequency responses are evaluated by using the cross-correlation method. Such a technique, as well as the tracking algorithm, is effectively implemented by using a field-programmable gate array, and it is validated by means of simulation and experimental results. [ABSTRACT FROM PUBLISHER]

Sliding mode is a control technique that is widely employed in switching converter applications. Such a nonlinear control technique, which is commonly implemented by means of analog circuitry only, forces the switches commutations by comparing a reference signal with a combination of signals acquired on the converter itself. In this way, the control action and the switching modulation are integrated in a single functional block. In this paper the implementation of the sliding mode controller in a low cost digital device is discussed. The proposed approach profits from features offered by some digital devices, e.g., the dsPic33FJ16GS502 family from Microchip Technology Inc., in order to make the implementation simple. In the paper, the aspects related to the accuracy of the comparison between the signals required by the sliding mode controller are discussed. Moreover, the elaboration time needed to calculate the signals that drive the converter's switching devices is the subject of an in-depth analysis. The techniques proposed in the paper have been validated by means of simulations and through experimental results performed on a switching dc/dc converter for photovoltaic applications. [ABSTRACT FROM PUBLISHER]

In this paper, a novel maximum power point tracking algorithm based on the perturb-and-observe (P&O) technique is introduced. The novelty of the approach is represented by the perturbation of more control variables, rather than just one. This allows the increase of the power extracted from the photovoltaic (PV) field as compared to the case of perturbation of a single control variable. The proposed technique overcomes the limitations of any existing tracking technique dedicated to PV arrays exhibiting a unique maximum power point, thus not only of the P&O approach, whenever dynamic constraints ensuring the correct system behavior must be fulfilled too. The proposed multivariable approach is described by means of its application to a single-stage one-cycle controlled PV inverter. [ABSTRACT FROM AUTHOR]