Search

A sampling current ratio measurement system has been developed to calibrate the voltage dependence of ratio error and phase displacement of current transformers (CTs) used for medium-voltage (MV) and high-voltage (HV) applications. The influence of voltage-induced leakage current on the apparent ratio error and phase displacement of the reference circuit was unambiguously demonstrated using a novel measurement method. Measurement results for voltages up to 24 kV show that the observed leakage current is purely capacitive and caused by the shielded cable capacitance of the HV cable used to feed the current. The maximum ratio error and phase displacement were found to be about 100 parts in 106 and $100~\mu $ rad for the smallest current of 100 A used for these investigations. Since these values scale linearly with the applied voltage and inversely proportional with current, the assumption of negligible voltage dependence used in other reference systems presented in literature is questionable. Using the corrected reference circuit, a commercial class 0.2S MV CT with 2500-A nominal current was calibrated at voltage levels up to 24 kV. The voltage dependence of ratio error and phase displacement for primary currents up to 500 A was demonstrated to be capacitive as well, with a maximum impact on the current ratio of almost 0.9% for a primary current of 100 A (corresponding to 3.6% at 1% of nominal current). This value is beyond the limits of in-force standards, which emphasizes the necessity of implementing voltage dependence testing in those standards. [ABSTRACT FROM AUTHOR]

To assess the reliability of dc energy measurement equipment on-board trains, a setup was developed to characterize current transducers under realistic operating conditions. The operating principle is based on a current ratio measurement technique. The reference sensor is a high-precision zero-flux current transducer in combination with a broadband high-precision current shunt. The influence of ac distortion on this reference sensor was found to be within a few parts in 106 using an initial version of the setup, in which ac distortion was applied through a separate winding. A revised version of the setup employs a programmable electronic load to apply dynamic currents up to 600 A. The setup was used to characterize a 100 $\mu \Omega $ high-current shunt resistor. The effect of dissipative heating on the dc transresistance error was around 0.03 %, with a settling time of about half an hour. The short-term intrinsic current dependence was also around 0.03 %. The effect of ac distortion was within a few parts in 106. The intrinsic current dependence and the onset of the heating effect were also observed when exposing the sensor to a dynamic current profile that was recorded during a trip between two successive underground train stations on Metro de Madrid. These results demonstrate that the setup described in this paper is very effective for characterizing dc current sensors for practical railway applications. Future work will concentrate on even more demanding current signals, such as chopped signals, and on other types of sensors and measurement systems. [ABSTRACT FROM AUTHOR]

AC–DC measurements have been performed on a commercial thermal transfer standard (TTS) using a pulse-driven ac Josephson voltage standard with a small cryostat enabling shorter voltage leads. A 20 mV RMS output voltage was chosen, close to the maximum value that can be obtained without lowfrequency compensation (at a sigma-delta code amplitude of about 10 %) and close to the upper limit of the TTS in its 22 mV range. The measured deviation at higher frequencies, which is due to the length of the voltage leads, was an order of magnitude smaller than was observed before with a normal cryostat. The observed square dependence on the signal frequency and cable length follows exactly the expected behavior. All results agree well with the calibrations performed using a micropot reference system. Furthermore, the influence of other cables and equipment was investigated. The measurement results can be quantitatively understood both in terms of a lumped circuit description and in terms of reflected waves. [ABSTRACT FROM AUTHOR]

A binary Josephson-array voltage standard was used to investigate the influence of device settings on the reading of an 8½-digit sampling voltmeter. This voltmeter is the heart of the primary standard for power at 50 Hz or 60 Hz at several national metrology institutes (NMIs). In this paper, we present results on the influence of the voltmeter synchronization and measurement parameters on the root-mean-square (RMS) measurements of Josephson stepwise-approximated sine waves for different frequencies. Our results show that for aperture times above 100 μs, the measured RMS voltage shows a large step in value with respect to shorter aperture times and is much more accurate. Furthermore, to obtain 0.2 μV/V accuracy, we show that for stepwise-approximated sine waves at 53 Hz, delay times higher than 10 μs are necessary. A slight delay time dependence limits the accuracy for frequencies above a few hundred hertz. [ABSTRACT FROM AUTHOR]