Search

A new electromagnetic band gap (EBG) structure based on the soft and hard surfaces for gap waveguide (GW) technology is introduced in this article. The proposed EBG structure consists of a soft surface and a hard surface in parallel with a gap between them, where the ridges/corrugations of the two surfaces are perpendicular to each other or with an angle near 90°. Compared with the contactless bed of nails EBG, the most widely used EBG structure in GW technology, the structural strength of the new EBG structure is increased significantly, which makes it very suited for high-frequency applications. Another advantage is that with the varying of the angle between the ridges/corrugations of the two surfaces, the stopband shifts in a wide frequency band, which makes the stopband tunable after the EBG is fabricated. The stopband performance of the proposed EBG is investigated. Straight and bended groove GWs (GGW) employing this new EBG are designed, manufactured and tested. The isolation performance with different columns of ridges/corrugations is also tested. The measured results show the proposed GGWs have excellent transmission performance. [ABSTRACT FROM AUTHOR]

This letter proposed a combined susceptibility diagram, applicable to investigating and differentiating the inherent mechanism of multipactor in dielectric-loaded microwave devices. This susceptibility diagram consists of average secondary emission yield on the dielectric surface and both the surfaces. Using this diagram, we predict the electron multiplication mechanism in the partially dielectric-loaded parallel-plate waveguide. It is found that the multipactor extinguishing only occurs for a low multipaction rate, while the saturation occurs for a higher multipaction rate. To verify its validity, the dynamic evolution of multipactor is investigated by electrostatic particle-in-cell. A good agreement between simulations and prediction results has been achieved. This susceptibility diagram thus constructed can provide a guidance to clearly identify the condition for multipactor extinguishing or saturation. [ABSTRACT FROM AUTHOR]

The aim of this article is to establish a general and practical analytical model of the one-sided multipactor on a dielectric of a metal surface and analyze the resonant multipactor effect for the recent growing interest in spacecrafts. A theoretical multipactor model involving a normal static electric field, a radio frequency (RF) electric field with both tangential and normal components, and the influence of the desorption gas is proposed. The kinetic properties and the resonant condition of the electron are studied by analytical calculations. The results show that the transit time of the electron decreases with the increase in the normal static electric field and the pressure of the desorption gas. The emission phase of the electron is the paramount factor that has a direct influence on the occurrence of the resonant multipactor. If the resonant multipactor effect could appear, the emission phase of the electron should be larger than a critical phase, and the ratio between the amplitude of the normal component of the RF electric field and the normal static electric field should be larger than a specific value as well. [ABSTRACT FROM AUTHOR]

A new kind of contactless electromagnetic bandgap (EBG) structure in the form of interdigital-pin bed of nails is introduced for the first time in this paper. It consists of two metal plates with interdigital-pin bed of nails face to face with each other, where each pin is surrounded by four pins on the other plate. The working mechanism of the interdigital-pin contactless EBG structure is suppressing the modes supported by the parallel plate waveguide (PPW) by loading interdigital pins inside the PPW. The advantage of the interdigital-pin lattice is there is a significant pin gap increase. This lattice makes the minimum pin gap that could be processed by the machining center, after assembling, reduced from the diameter of the milling clutter to its radius. It provides a way to process EBG structures at higher frequency band with the same milling cutter. The cases the pins allocated between the two plates in a random manner are also studied. Compared to its traditional counterpart, the stopband is stable with a small variation. A W-band groove gap waveguide (GGW) prototype with interdigital-pins and a Ka-band GGW with randomly allocated pins are designed, manufactured, and tested. The measured results agree well with the simulation. [ABSTRACT FROM AUTHOR]

The underlying mechanisms of multipactor between dielectric and metal and the discharge threshold of practical dielectric components have been investigated numerically and experimentally in this paper. The reduction in secondary electron yield (SEY) and the change in surface condition are achieved using the microstructure processing technology on both of ferrite dielectric and metal. Combined with the electromagnetic particle-in-cell method, the SEY model fit with the experimental data is utilized to simulate multipactor in three groups of ferrite circulators with different surface conditions. Simulation and experimental results demonstrate that the multipactor threshold of the circulator is increased by a factor of 2 through the SEY reduction on the ferrite and is increased by a factor of more than 8, from 380 W to more than 3400 W, through the SEY reduction on both of the ferrite and the metal. Different multipactor discharge mechanisms, including two-side multipactor with positive charge accumulation, singe-side multipactor with negative charge accumulation, and multipactor suppression effect, exist in circulators with the same physical structure and different surface conditions. [ABSTRACT FROM AUTHOR]

Passive intermodulation (PIM) is one of the major reliability problems in microwave communication systems. In this paper, the PIM interference generated by the metal–insulator–metal (MIM) contact nonlinearity was analytically modeled and experimentally verified. The pressure-dependent nonlinear $I$ – $V$ equations of the MIM contact were derived based on electrical contact theory and verified using a manufactured MIM contact structure. Then a point source model for the PIM product based on the metallic contact nonlinearity was proposed. The PIM product is mainly determined by the contact resistance, surface current density, and nonlinear current coefficient from the model, and in the small contact resistance region, the PIM level decreasing rates are 60, 60, and 20 dB/decade by decreasing the contact resistance, surface current density, and the nonlinear current coefficient, respectively. A designated PIM current source was utilized to verify the relationship. In the end, the PIM equation for the rectangular waveguide connection was derived based on the point source model. This model will provide guidance on low PIM system design. [ABSTRACT FROM PUBLISHER]

• Secondary electron yield of inert metals increases with exposure time. • Surface adsorption layer consisting of carbon and oxygen elements results in the increase. • A two-layers secondary electron yield model is established and parameters of adsorption layer are obtained. • The increase of secondary electron yield can significantly reduce the multipactor threshold. The secondary electron emission (SEE) property of materials is closely related to the multipactor, which is one of the potential risk factors affecting the reliability of high power microwave components for space application. In the presented work, the influence of atmospheric exposure on the secondary electron yield (SEY) of the inert metal is investigated. It is found that the SEY increases gradually with exposing time, and the increase in SEY results from the surface adsorption layer consisting of carbon and oxygen elements. A two-layers SEY model is established to explain this evolution and obtain the corresponding parameters of the adsorption layer. Simulation on a C band impedance transformer shows that 45 days of exposure will result in a 7.5 dB decrease of multipactor threshold. [ABSTRACT FROM AUTHOR]