Search

Objective Bulk fracture is one of the primary reasons for resin-based dental restoration failures. To date, there has been no report on the use of polymerizable dental monomers with acceptable biocompatibility to develop a resin with substantial self-healing capability. The objectives of this study were to: (1) develop a self-healing resin containing microcapsules with triethylene glycol dimethacrylate (TEGDMA)- N , N -dihydroxyethyl- p -toluidine (DHEPT) healing liquid in poly(urea-formaldehyde) (PUF) shells for the first time, and (2) determine the physical and mechanical properties, self-healing efficiency, and fibroblast cytotoxicity. Methods Microcapsules of polymerizable TEGDMA-DHEPT in PUF were prepared via an in situ polymerization method. Microcapsules were added into a BisGMA-TEGDMA resin at microcapsule mass fractions of 0%, 5%, 10%, 15% and 20%. A flexural test was used to measure composite strength and elastic modulus. A single edge V-notched beam method was used to measure fracture toughness K IC and self-healing efficiency. Results Flexural strength and elastic modulus (mean ± sd; n = 6) of resin containing 5–15% microcapsules were similar to control without microcapsules ( p > 0.1). Adding microcapsules into the resin increased the virgin K IC , which was about 40% higher at 15% microcapsules than that with 0% microcapsules ( p < 0.05). Specimens were fractured and healed, then fractured again to measure the healed K IC . A self-healing efficiency of about 65% in K IC recovery was obtained with 10–20% microcapsules. All specimens with 0–20% microcapsules had fibroblast viability similar to control without resin eluents ( p > 0.1). Significance Self-healing dental resin containing microcapsules with polymerizable TEGDMA-DHEPT healing liquid in PUF shells were prepared for the first time with excellent self-healing capability. These microcapsules and self-healing resins containing them may be promising for dental restorations to heal cracks/damage and increase durability. [ABSTRACT FROM AUTHOR]

Abstract: Objective: Quaternary amine charge density is important because when the negatively charged bacteria contact the positive quaternary amine charge, the electric balance is disturbed and the bacterium could be disrupted. There has been no report on the effects of charge density on the antibacterial efficacy of dental bonding agents. The objective of this study was to synthesize a new quaternary ammonium methacrylate, and investigate the effects of charge density of bonding agent on bacteria early-attachment, biofilm colony-forming units (CFU) and dentin bond strength. Methods: Dimethylaminododecyl methacrylate (DMAHDM) with an alkyl chain length of 16 was synthesized and mixed into Scotchbond Multi-Purpose adhesive and primer (SBMP) at mass fractions of 0%, 2.5%, 5%, 7.5%, and 10%. A microtensile dentin bond test was performed. The density of quaternary ammonium groups was measured using a fluorescein dye method. Streptococcus mutans (S. mutans) early-attachment was examined at 4h, and biofilm colony-forming units (CFU) were measured at 2 days. Results: All groups had similar microtensile bonding strengths (mean±sd; n =40) of about 60MPa (p >0.1). Quaternary amine charge density of bonding agents monotonically increased with increasing DMAHDM mass fraction. Bacteria early-attachment coverage greatly decreased with increasing DMAHDM content in the resin. Biofilm CFU at 10% DMAHDM was reduced by more than 4log, compared to SBMP control. Charge density of bonding agent was inversely proportional to bacteria early-attachment coverage and biofilm CFU. Significance: Increasing the quaternary amine charge density of dentin bonding agent resin was shown to greatly reduce S. mutans attachment and decrease biofilm CFU by four orders of magnitude, without compromising the dentin bond strength. The new DMAHDM is promising for use in bonding agents and other antibacterial restorative materials to inhibit caries. [Copyright &y& Elsevier]

Abstract: Objectives: Calcium and phosphate ion-releasing resin composites are promising for remineralization. However, there has been no report on incorporating antibacterial agents to these composites. The objective of this study was to develop antibacterial and mechanically strong nanocomposites incorporating a quaternary ammonium dimethacrylate (QADM), nanoparticles of silver (NAg), and nanoparticles of amorphous calcium phosphate (NACP). Methods: The QADM, bis(2-methacryloyloxyethyl) dimethylammonium bromide (ionic dimethacrylate-1), was synthesized from 2-(N,N-dimethylamino)ethyl methacrylate and 2-bromoethyl methacrylate. NAg was synthesized by dissolving Ag 2-ethylhexanoate salt in 2-(tert-butylamino)ethyl methacrylate. Mechanical properties were measured in three-point flexure with bars of 2mm×2mm×25mm (n =6). Composite disks (diameter=9mm, thickness=2mm) were inoculated with Streptococcus mutans. The metabolic activity and lactic acid production of biofilms were measured (n =6). Two commercial composites were used as controls. Results: Flexural strength and elastic modulus of NACP+QADM, NACP+NAg, and NACP+QADM+NAg matched those of commercial composites with no antibacterial property (p >0.1). The NACP+QADM+NAg composite decreased the titer counts of adherent S. mutans biofilms by an order of magnitude, compared to the commercial composites (p <0.05). The metabolic activity and lactic acid production of biofilms on NACP+QADM+NAg composite were much less than those on commercial composites (p <0.05). Combining QADM and NAg rendered the nanocomposite more strongly antibacterial than either agent alone (p <0.05). Significance: QADM and NAg were incorporated into calcium phosphate composite for the first time. NACP+QADM+NAg was strongly antibacterial and greatly reduced the titer counts, metabolic activity, and acid production of S. mutans biofilms, while possessing mechanical properties similar to commercial composites. These nanocomposites are promising to have the double benefits of remineralization and antibacterial capabilities to inhibit dental caries. [Copyright &y& Elsevier]

Implant-related infections from the adhesion and proliferation of dental plaque are a major challenge for dental implants. The objectives of this study were to: (1) develop novel antibacterial titanium (Ti) healing abutment; (2) investigate the inhibition of implant infection-related pathogenic bacteria and saliva-derived biofilm, and evaluate the biocompatibility of the new material for the first time. Dimethylaminohexadecyl methacrylate (DMAHDM) and hydroxyapatite (HAP) were polymerized via polydopamine (PDA) on Ti. Staphylococcus aureus (S. aureus), Streptococcus sanguinis (S. sanguinis) and human saliva-derived biofilms were tested. After 4 weeks of DMAHDM release, the antibacterial efficacy of the DMAHDM remaining on Ti surface and the DMADHM in medium was tested. Biocompatibility was determined using human gingival fibroblasts (HGFs) and periodontal ligament stem cells (PDLSCs). The DMAHDM-loaded coating filled into the nano-voids in Ti surfaces. The modified Ti showed potent antibacterial activity, reducing the CFU of S. aureus , S. sanguinis and saliva-derived biofilms by 8, 7 and 4 log, respectively (P < 0.05). After 4 weeks of release, the modified Ti was still able to reduce S. aureus and S. sanguinis biofilm CFU by 1–3 log (P < 0.05). This provided strong antibacterial function for more than 4 weeks, which were the high-risk period for implant infections. The new material showed excellent biocompatibility when compared to control (P > 0.05). Novel DMAHDM-loaded Ti healing abutment had strong antibacterial effects, reducing biofilm CFUs by orders of magnitude, and lasting for over four weeks to cover the high-risk period for implant infections. The novel antibacterial Ti is promising to combat implant-related infections in dental, craniofacial and orthopedic applications. • The DMAHDM-loaded Ti effectively inhibit biofilms on the surface in the high-risk period of peri-implant inflammation. • The released DMAHDM inhibited the surrounding planktonic S. aureus and S. sanguinis. • After 4 weeks, the modified Ti was still able to show antibacterial effects on S. aureus and S. sanguinis biofilm. • The DMAHDM-loaded Ti is biocompatible, with no cytotoxicity to soft tissue seal and osseointegration related cells. [ABSTRACT FROM AUTHOR]

Pit and fissure sealants with antibacterial and remineralization properties have broad application prospects in caries prevention. The objectives of this study were to: (1) develop a novel pit and fissure sealant containing CaF 2 nanoparticles (nCaF 2) and dimethylaminohexadecyl methacrylate (DMAHDM); and (2) investigate the effects of nCaF 2 and DMAHDM on biofilm response and fluoride (F) ion release for the first time. Helioseal F was used as a control. Bioactive sealants were formulated with DMAHDM and nCaF 2. Flow properties, enamel shear bond strength, hardness and F ion releases were measured. Streptococcus mutans (S. mutans) biofilms were grown on sealants. Biofilm metabolic activity, lactic acid production, colony-forming units (CFU), and pH of biofilm culture medium were measured. Adding 5% DMAHDM and 20% nCaF 2 did not reduce the paste flow and enamel bond strength, compared to control (p < 0.05). Hardness of sealants with 20% nCaF 2 and DMAHDM was higher than control (p < 0.05). The F ion release from 20% nCaF 2 was much higher than that of commercial control (p < 0.05). The sealant with DMAHDM reduced the S. mutans biofilm CFU by 4 logs. The pH in biofilm medium of the new bioactive sealant was much higher (pH 6.8) than that of commercial sealant (pH 4.66) (p < 0.05). The new bioactive pit and fissure sealant with nCaF 2 and DMAHDM achieved high fluoride release and strong antibacterial performance. This novel fluoride-releasing and antibacterial sealant is promising to inhibit caries and promote the remineralizaton of enamel and dentin. [ABSTRACT FROM AUTHOR]

• S. mutans rnc gene-deletion reduced the biofilm growth and acid production in antibacterial monomer. • DMAHDM was shown to have a stronger antibacterial function than CHX. • The dual strategy of combining rnc -deletion with DMAHDM achieved the greatest reduction in biofilms. • The novel dual strategy is promising for a wide range of dental applications. Antibacterial quaternary ammonium monomers (QAMs) are used in resins. The rnc gene in Streptococcus mutans (S. mutans) plays a key role in resisting antibiotics. The objectives of this study were to investigate for the first time: (1) the effects of rnc deletion on S. mutans biofilms and acid production; (2) the combined effects of rnc deletion with dimethylaminohexadecyl methacrylate (DMAHDM) on biofilm-inhibition efficacy. Parent S. mutans strain UA159 (ATCC 700610) and the rnc -deleted S. mutans were used. Bacterial growth, minimum inhibitory concentration (MIC), and minimal bactericidal concentration (MBC) were measured to analyze the bacterial susceptibility of the parent and rnc -deleted S. mutans against DMAHDM, with the gold-standard chlorhexidine (CHX) as control. Biofilm biomass, polysaccharide and lactic acid production were measured. The drug-susceptibility of the rnc -deleted S. mutans to DMAHDM or CHX was 2-fold higher than parent S. mutans. The drug-susceptibility did not increase after 10 passages (p < 0.05). Deleting the rnc gene increased the biofilm susceptibility to DMAHDM or CHX by 2-fold. The rnc -deletion in S. mutans reduced biofilm biomass, polysaccharide and lactic acid production, even at no drugs. DMAHDM was nearly 40 % more potent than the gold-standard CHX. The combination of rnc deletion + DMAHDM treatment achieved the greatest reduction in biofilm biomass, polysaccharide synthesis, and lactic acid production. Gene modification by deleting the rnc in S. mutans reduced the biofilm growth and acid production, and the rnc deletion + DMAHDM method showed the greatest biofilm-inhibition efficacy, for the first time. The dual strategy of antibacterial monomer + bacterial gene modification shows great potential to control biofilms and inhibit caries. [ABSTRACT FROM AUTHOR]

Objectives: Composites are commonly used for tooth restorations, but recurrent caries often lead to restoration failures due to polymerization shrinkage-stress-induced marginal leakage. The aims of this research were to: (1) develop novel low-shrinkage-stress (L.S.S.) nanocomposites containing dimethylaminododecyl methacrylate (DMADDM) with nanoparticles of calcium fluoride (nCaF2) or amorphous calcium phosphate (NACP) for remineralization; (2) investigate antibacterial and cytocompatibility properties. Methods: Nanocomposites were made by mixing triethylene glycol divinylbenzyl ether with urethane dimethacrylate containing 3% DMADDM, 20% nCaF2, and 20% NACP. Flexural strength, elastic modulus, antibacterial properties against Streptococcus mutans biofilms, and cytotoxicity against human gingival fibroblasts and dental pulp stem cells were tested. Results: Nanocomposites with DMADDM and nCaF2 or NACP had flexural strengths matching commercial composite control without bioactivity. The new nanocomposite provided potent antibacterial properties, reducing biofilm CFU by 6 logs, and reducing lactic acid synthesis and metabolic function of biofilms by 90%, compared to controls (p < 0.05). The new nanocomposites produced excellent cell viability matching commercial control (p > 0.05). Conclusions: Bioactive L.S.S. antibacterial nanocomposites with nCaF2 and NACP had excellent bioactivity without compromising mechanical and cytocompatible properties. The new nanocomposites are promising for a wide range of dental restorations by improving marginal integrity by reducing shrinkage stress, defending tooth structures, and minimizing cariogenic biofilms. [ABSTRACT FROM AUTHOR]

The cariogenic biofilm on enamel, restoration, and bonding interface is closely related to dental caries and composite restoration failure. Enamel remineralization at adhesive interface is conducive to protecting bonding interface and inhibiting secondary caries. This study intended to assess the remineralization efficiency of adhesive with dimethylaminohexadecyl methacrylate (DMAHDM) and nanoparticles of amorphous calcium phosphate (NACP) on initial caries lesion of biofilm-coated enamel. Artificial initial carious lesion was created via 72-hour immersion in demineralization solution and cariogenic biofilm was formed after 24-hour culture of Streptococcus mutans (S. mutans). Specimens were then divided into 4 groups: enamel control, enamel treated with NACP, DMAHDM and NACP+DMAHDM respectively. Samples next underwent 7-day cycling, 4 h in BHIS (brain heart infusion broth containing 1 % sucrose) and 20 h in AS (artificial saliva) per day. The pH of BHIS was tested daily. So did the concentration of calcium and phosphate in BHIS and AS. Live/dead staining, colony-forming unit (CFU) count, and lactic acid production of biofilms were measured 7 days later. The enamel remineralization efficiency was evaluated by microhardness testing and transverse microradiography (TMR) quantitatively. Enamel of NACP+DMAHDM group demonstrated excellent remineralization effectiveness. And the NACP+DMAHDM adhesive released a great number of Ca2+ and PO 4 3- ions, increased pH to 5.81 via acid neutralization, decreased production of lactic acid, and reduced CFU count of S. mutans (P < 0.05). The NACP+DMAHDM adhesive would be applicable to preventing secondary caries, strengthening enamel-adhesive interface, and extending the lifespan of composite restoration. [ABSTRACT FROM AUTHOR]

The objectives of this study were to: (1) develop a multifunctional adhesive via dimethylaminohexadecyl methacrylate (DMAHDM) and nanoparticles of amorphous calcium phosphate (NACP); and (2) investigate its ability to provide metalloproteinases (MMPs) deactivation and remineralization for long-term dentin bonding durability. DMAHDM and NACP were incorporated into Adper™ Single Bond 2 Adhesive (SB2) at mass fractions of 5% and 20%, respectively. Degree of conversion and contact angle were measured. Endogenous MMP activity of the demineralized dentin beams, Masson's trichrome staining, nano-indentation, microtensile bond strength and interfacial nanoleakage analyses were investigated after 24 h and 3 months of storage aging in artificial saliva. Adding DMAHDM and NACP did not compromise the degree of conversion and contact angle of SB2 (p > 0.05). DMAHDM and NACP incorporation reduced the endogenous MMP activity by 53 %, facilitated remineralization, and increased the Young's modulus of hybrid layer by 49 % after 3 months of aging in artificial saliva, compared to control. For SB2 Control, the dentin bond strength decreased by 38 %, with greater nanoleakage expression, after 3 months of aging (p < 0.05). However, DMAHDM+NACP group showed no loss in bond strength, with much less nanoleakage, after 3 months of aging (p > 0.05). DMAHDM+NACP adhesive greatly reduced MMP-degradation activity in demineralized dentin, induced remineralization at adhesive-dentin interface, and maintained the dentin bond strength after aging, without adversely affecting polymerization and dentin wettability. This new adhesive has great potential to help eliminate secondary caries, prevent hybrid layer degradation, and increase the resin-dentin bond longevity. [ABSTRACT FROM AUTHOR]

Objectives: Demineralized lesions in tooth enamel around orthodontic brackets are caused by acids from cariogenic biofilm. This study aimed to develop a novel antibacterial orthodontic cement by incorporating a quaternary ammonium monomer dimethylaminododecyl methacrylate (DMADDM) into a commercial orthodontic cement, and to investigate the effects on microcosm biofilm response and enamel bond strength. Methods: DMADDM, a recently-synthetized antibacterial monomer, was incorporated into orthodontic cement at 0%, 1.5%, 3% and 5% mass fractions. Bond strength of brackets to enamel was measured. A microcosm biofilm model was used to measure metabolic activity, lactic acid production, and colony-forming units (CFU) on orthodontic cements. Results: Shear bond strength was not reduced at 3% DAMDDM (p > 0.1), but was slightly reduced at 5% DMADDM, compared to 0% DMADDM. Biofilm viability was substantially inhibited when in contact with orthodontic cement containing 3% DMADDM. Biofilm metabolic activity, lactic acid production, and CFU were much lower on orthodontic cement containing DMADDM than control cement (p < 0.05). Conclusions: Therefore, the novel antibacterial orthodontic cement containing 3% DMADDM inhibited oral biofilms without compromising the enamel bond strength, and is promising to reduce or eliminate demineralization in enamel around orthodontic brackets. [ABSTRACT FROM AUTHOR]

A low-shrinkage-stress (LSS), antibacterial and remineralizing nanocomposite was recently developed; however, validation of its long-term antibacterial potency in modulating human salivary-derived biofilm is an unmet need. This study aimed to evaluate the antibacterial effect of the bioactive LSS composite before and after aging in acidic solution for 90 days using a multi-species biofilm model, and to evaluate its cytotoxicity. The LSS composite consisted of urethane dimethacrylate (UDMA) and triethylene glycol divinylbenzyl ether (TEG-DVBE), 3% dimethylaminohexadecyl methacrylate (DMAHDM) and 20% nanoparticles of amorphous calcium phosphate (NACP). Biofilm colony-forming units (CFU), lactic acid production, and confocal laser scanning microscopy (3D biofilm) were evaluated before and after three months of aging. Cytotoxicity was assessed against human gingival fibroblasts (HGF). The new LSS composite presented the lowest biofilm CFU, lactic acid and biofilm biomass, compared to controls (n = 6, p < 0.05). Importantly, the new composite exhibited no significant difference in antibacterial performance before and after 90-day-aging, demonstrating long-term antibacterial activity (p > 0.1). The LSS antibacterial and remineralizing composite presented a low cell viability at original extract that has increased with further dilutions. In conclusion, this study spotlighted that the new bioactive composite not only had a low shrinkage stress, but also down-regulated the growth of oral biofilms, reduced acid production, maintained antibacterial activity after the 90-day-aging, and did not compromise the cytocompatibility. [ABSTRACT FROM AUTHOR]

Dentin remineralization at the bonded interface would protect it from external risk factors, therefore, would enhance the longevity of restoration and combat secondary caries. Dental biofilm, as one of the critical biological factors in caries formation, should not be neglected in the assessment of caries preventive agents. In this work, the remineralization effectiveness of demineralized human dentin in a multi-species dental biofilm environment via an adhesive containing nanoparticles of amorphous calcium phosphate (NACP) and dimethylaminohexadecyl methacrylate (DMAHDM) was investigated. Dentin demineralization was promoted by subjecting samples to a three-species acidic biofilm containing Streptococcus mutans , Streptococcus sanguinis, Streptococcus gordonii for 24 h. Samples were divided into a control group, a DMAHDM adhesive group, an NACP group, and an NACP + DMAHDM adhesive group. A bonded model containing a control-bonded group, a DMAHDM-bonded group, an NACP-bonded group, and an NACP + DMAHDM-bonded group was also included in this study. All samples were subjected to a remineralization protocol consisting of 4-h exposure per 24-h period in brain heart infusion broth plus 1% sucrose (BHIS) followed by immersion in artificial saliva for the remaining period. The pH of BHIS after 4-h immersion was measured every other day. After 14 days, the biofilm was assessed for colony-forming unit (CFU) count, lactic acid production, live/dead staining, and calcium and phosphate content. The mineral changes in the demineralized dentin samples were analyzed by transverse microradiography. The in vitro experiment results showed that the NACP + DMAHDM adhesive effectively achieved acid neutralization, decreased biofilm colony-forming unit (CFU) count, decreased biofilm lactic acid production, and increased biofilm calcium and phosphate content. The NACP + DMAHDM adhesive group had higher remineralization value than the NACP or DMAHDM alone adhesive group. The NACP + DMAHDM adhesive was effective in remineralizing dentin lesion in a biofilm model. It is promising to use NACP + DMAHDM adhesive to protect bonded interface, inhibit secondary caries, and prolong the longevity of restoration. [ABSTRACT FROM AUTHOR]

Root canal re-infection and weakening of roots are two main challenges in endodontics. The objectives of the study were: (1) to develop a novel root canal sealer containing dimethylaminohexadecyl methacrylate (DMAHDM), nanoparticles of silver (NAg), and nanoparticles of amorphous calcium phosphate (NACP), and (2) to investigate the effects on the physical, anti-biofilm, remineralizing ions, and hardness of human dentin for the first time. Methacrylate-resin dual-cured root canal sealer contained 5% DMAHDM, 0.15% NAg, and NACP at 10%, 20% and 30% mass fractions. The flow, film thickness, and Ca and P ions release were investigated. The effects of NACP on radicular dentin hardness after treatment with sodium hypochlorite (NaOCL) and ethylenediaminetetraacetic acid (EDTA) were assessed. Antibacterial properties were measured against Enterococcus faecalis (E. faecalis) -impregnated dentin blocks; colony-forming units (CFU) and live/dead assays were measured. Incorporating DMAHDM, NAg and NACP did not adversely influence the flow and film thickness properties. Sealer with 30% NACP neutralized the acid and increased the solution pH (p < 0.05). Sealer containing 30% NACP regenerated dentin minerals lost due to NaOCL and EDTA treatment, and increased the dentin hardness to match that of sound dentin (p > 0.1). Incorporating 5% DMAHDM and 0.15% NAg reduced biofilm CFU of E. faecalis -impregnated dentin blocks by nearly 3 logs when compared control group (p < 0.05). The novel therapeutic root canal sealer with triple bioactive agents of DMAHDM, NAg and NACP neutralized acid, raised the pH, regenerated dentin minerals, increased root dentin hardness, and reduced dentin-block-impregnated biofilm CFU by 3 logs. This new sealer with highly desirable antibacterial and remineralization properties are promising to increase the success rate of endodontic therapy and strengthen the tooth root structures. [ABSTRACT FROM AUTHOR]

Endodontic treatment failures and recontamination remain a major challenge. The objectives of this study were to: (1) develop a new root canal sealer with potent and long-lasting antibiofilm effects using dimethylaminohexadecyl methacrylate (DMAHDM) and nanoparticles of silver (NAg); (2) determine the effects of incorporating DMAHDM and NAg each alone versus in combination on biofilm-inhibition efficacy; and (3) determine the effects on sealer paste flow, film thickness and sealing ability, compared to a commercial control sealer. Dual-cure endodontic sealers were formulated using DMAHDM mass fractions of 0%, 2.5% and 5%, and NAg mass fractions of 0.05%, 0.1% and 0.15%. The sealing ability of the sealers was measured using linear dye penetration method. Colony-forming units (CFU), live/dead assay, and polysaccharide production of biofilms grown on sealers were determined. The sealer with 5% DMAHDM and 0.15% NAg yielded a flow of (22.18 ± 0.58) which was within the range of ISO recommendations and not statistically different from AH Plus control (23.3 ± 0.84) (p > 0.05). Incorporating DMAHDM and NAg did not negatively affect the film thickness and sealing properties (p > 0.05). The sealer with 5% DMAHDM and 0.15% NAg greatly reduced polysaccharide production by the biofilms, and decreased the biofilm CFU by nearly 6 orders of magnitude, compared to AH Plus and experimental controls (p < 0.05). A therapeutic root canal sealer was developed using 5% DMAHDM with biofilm-inhibition through contact-mediated mechanisms, plus 0.15% of NAg to release silver ions into the complex and difficult-to-reach root canal environment. The novel root canal sealer exerted potent antibiofilm effects and reduced biofilm CFU by 6 orders of magnitude without compromising sealer flow, film thickness and sealing ability. This method provided a promising approach to inhibit endodontic biofilms and prevent recurrent endodontic infections. [ABSTRACT FROM AUTHOR]

The objectives of this studywere to: (1) develop a novel bioactive nanocomposite for Class V restorations with subgingival margins to inhibit periodontal pathogens; and (2) investigate if the bioactive nanocomposite could inhibit multi-species periodontal biofilms with a potency as strong as that against single species biofilms. Nanocomposite was fabricated using dimethylaminohexadecyl methacrylate (DMAHDM), 2-methacryloyloxyethyl phosphorylcholine (MPC) and nanoparticles of amorphous calcium phosphate (NACP). Biofilms with 1, 3, 6 and 9 species of periodontal pathogens were grown on the composites and tested for live/dead staining, colony-forming units (CFU), metabolic activity, and biofilm matrix polysaccharide production. The bioactive composite reduced protein adsorption by an order of magnitude (p < 0.05) and greatly reduced biofilm viability. It decreased the biofilm CFU by more than 3 orders of magnitude for all four types of periodontal biofilms, compared to control composite. With increasing the biofilm species from 1 to 9, the antibacterial efficacy of DMAHDM composite decreased; the CFU reduction folds decreased from 947 folds to 44 folds. In contrast, the MPC + DMAHDM composite maintained a CFU reduction folds of greater than 3000, showing a similar antibacterial potency from 1 to 9 species in the biofilms (p > 0.1). Dual agents MPC + DMAHDM achieved the greatest inhibition in biofilm, without decreasing its antibacterial potency when the biofilm species was increased from 1 to 9. A single agent became less effective when the biofilm species was increased from 1 to 9. The multifunctional MPC + DMAHDM composite is promising for root caries treatment and Class V restorations with subgingival margins to effectively inhibit multispecies periodontal biofilms, combat periodontitis and protect the periodontium. [ABSTRACT FROM AUTHOR]

Highlights • Incorporating DMADDM into GIC yielded potent and long-lasting antibiofilm properties. • Changes of mechanical properties of DMADDM-GIC are tolerable after 6 months of water aging. • The DMADDM containing GIC is a promising material to inhibit biofilms on the surface of restorations. Abstract Objectives The aims of this study were to investigate the effects of water aging for up to 6 months on the mechanical and anti-biofilm properties of a novel antibacterial glass ionomer cement (GIC) containing dimethylaminododecyl methacrylate (DMADDM). Methods GIC specimens (n = 180) which contained DMADDM (0 wt.%, 1.1 wt.% or 2.2 wt.%) were prepared. The mechanical properties surface roughness, microhardness and the surface charge density of ammonium groups were measured before and after water aging for 3 and 6 months at 37 °C. Further six months aged specimens (n = 216) were worn by 6 volunteers in their oral cavities for 24 h and 72 h. Biofilm formation was analyzed and rated by fluorescence microscopy (FM) and by scanning electron microscopy (SEM). Biofilm viability was analyzed by FM. Results Water aging did not show any adverse effects on the surface roughness and hardness of the material. The surface charge density of the GIC samples containing DMADDM decreased due to the aging procedure, however, was still higher than that of the GIC without DMADDM. In situ biofilm formation was significantly reduced after 24 h on DMADDM containing GIC (p < 0.05). FM results showed a higher ratio of red/green fluorescence on GIC-DMADDM samples. Significance Incorporating DMADDM into GIC affected the material properties in a tolerable manner even after 6 months of storage in water. The new GIC is a promising material to affect the biofilm formation on the surface of restorations. [ABSTRACT FROM AUTHOR]

Abstract Recurrent caries often occurs and is a primary reason for the failure of dental composite restorations. The objectives of this study were to: (1) develop a bioactive composite containing dimethylaminohexadecyl methacrylate (DMAHDM), (2) investigate its antibacterial effects and suppression on biofilm growth, and (3) investigate its ability to modulate biofilm species composition for the first time. DMAHDM was incorporated into a composite at mass% of 0%, 0.75%, 1.5%, 2.25% and 3%. A commercial composite Heliomolar served as a comparative control. A biofilm model consisting of Streptococcus mutans (S. mutans), Streptococcus sanguinis (S. sanguinis) and Streptococcus gordonii (S. gordonii) was tested by growing biofilms for 48 h and 72 h on composites. Colony-forming units (CFUs), metabolic activity and live/dead staining were evaluated. Lactic acid and polysaccharide productions were measured to assess biofilm cariogenicity. TaqMan real-time polymerase chain reaction was used to determine the proportion of each species in the biofilm. DMAHDM-containing composite had a strong anti-biofilm function, reducing biofilm CFU by 2–3 orders of magnitude, compared to control composite. Biofilm metabolic activity, lactic acid and polysaccharides were decreased substantially, compared to control (p < 0.05). At 72 h, the cariogenic S. mutans proportion in the biofilm on the composite with 3% DMAHDM was 19.9%. In contrast, an overwhelming S. mutans proportion of 92.2% and 91.2% existed in biofilms on commercial control and 0% DMAHDM, respectively. In conclusion, incorporating DMAHDM into dental composite: (1) yielded potent anti-biofilm properties; (2) modulated the biofilm species composition toward a non-cariogenic tendency. The new DMAHDM composite is promising for applications in a wide range of tooth cavity restorations to modulate oral biofilm species and combat caries. Highlights • Developed a bioactive dental composite containing DMAHDM. • Composite with 3% DMAHDM achieved greatest reduction in multispecies biofilm. • Biofilm equilibrium shifted from a cariogenic species-dominated state to a noncariogenic species-dominated state. • The new composite is promising for cavity restorations to combat caries. [ABSTRACT FROM AUTHOR]

Objectives A nanoparticle-doped adhesive that can be controlled with magnetic forces was recently developed to deliver drugs to the pulp and improve adhesive penetration into dentin. However, it did not have bactericidal and remineralization abilities. The objectives of this study were to: (1) develop a magnetic nanoparticle-containing adhesive with dimethylaminohexadecyl methacrylate (DMAHDM), amorphous calcium phosphate nanoparticles (NACP) and magnetic nanoparticles (MNP); and (2) investigate the effects on dentin bond strength, calcium (Ca) and phosphate (P) ion release and anti-biofilm properties. Methods MNP, DMAHDM and NACP were mixed into Scotchbond SBMP at 2%, 5% and 20% by mass, respectively. Two types of magnetic nanoparticles were used: acrylate-functionalized iron nanoparticles (AINPs); and iron oxide nanoparticles (IONPs). Each type was added into the resin at 1% by mass. Dentin bonding was performed with a magnetic force application for 3 min, provided by a commercial cube-shaped magnet. Dentin shear bond strengths were measured. Streptococcus mutans biofilms were grown on resins, and metabolic activity, lactic acid and colony-forming units (CFU) were determined. Ca and P ion concentrations in, and pH of biofilm culture medium were measured. Results Magnetic nanoparticle-containing adhesive using magnetic force increased the dentin shear bond strength by 59% over SBMP Control ( p < 0.05). Adding DMAHDM and NACP did not adversely affect the dentin bond strength ( p > 0.05). The adhesive with MNP + DMAHDM + NACP reduced the S. mutans biofilm CFU by 4 logs. For the adhesive with NACP, the biofilm medium became a Ca and P ion reservoir. The biofilm culture medium of the magnetic nanoparticle-containing adhesive with NACP had a safe pH of 6.9, while the biofilm medium of commercial adhesive had a cariogenic pH of 4.5. Significance Magnetic nanoparticle-containing adhesive with DMAHDM and NACP under a magnetic force yielded much greater dentin bond strength than commercial control. The novel adhesive reduced biofilm CFU by 4 logs and increased the biofilm pH from a cariogenic pH 4.5–6.9, and therefore is promising to enhance the resin–tooth bond, strengthen tooth structures, and suppress secondary caries at the restoration margins. [ABSTRACT FROM AUTHOR]

The effects of dimethylaminododecyl methacrylate (DMADDM) modified titanium implants on bacterial activity and microbial ecosystem of saliva-derived biofilm were investigated for the first time. Titanium discs were coated with DMADDM solutions at mass fractions of 0 mg/mL (control), 1, 5 and 10 mg/mL, respectively. Biomass accumulation and metabolic activity of biofilms were tested using crystal violet assay and MTT (3-(4,5-Dimethyl-thiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay. 16S rRNA gene sequencing was performed to measure the microbial community. Live/dead staining and scanning electron microscopy (SEM) were used to value the structure of biofilm. The results showed that the higher mass fraction of DMADDM the coating solution had, the significantly lower the values of metabolic activity and accumulated biofilms got, as well as fewer live cells and less extracellular matrix. Moreover, 5 mg/mL of DMADDM was the most effective concentration, as well as 10 mg/mL. In microecosystem-regulation, the DMADDM modified titanium implant decreased the relative abundance of Neisseria and Actinomyces and increased the relative abundance of Lactobacillus, a probiotic for peri-implant diseases. In conclusion, via inhibiting growth and regulating microecosystem of biofilm, this novel titanium implant coating with DMADDM was promising in preventing peri-implant disease in an 'ecological manner'. [ABSTRACT FROM AUTHOR]

Objectives The occurrence of tooth root caries is increasing as the world population ages and tooth retention in seniors increases. Class V restorations with subgingival margins are difficult to clean and often lead to periodontitis. The objectives of this study were to develop a Class V composite containing dimethylaminohexadecyl methacrylate (DMAHDM) and nanoparticles of amorphous calcium phosphate (NACP), and investigate mechanical properties and the inhibition of six species of periodontitis-related biofilms for the first time. Methods Ethoxylated bisphenol A dimethacrylate (EBPADMA) and pyromellitic glycerol dimethacrylate (PMGDM) were mixed at 1:1 mass ratio to form the resin matrix. DMAHDM, NACP, and glass particles were incorporated at 3%, 20% and 50% by mass, respectively. Six species were tested: Porphyromonas gingivalis , Prevotella intermedia , Prevotella nigrescens , Aggregatibacter actinomycetemcomitans , Fusobacterium nucleatum and Enterococcus faecalis . Colony-forming units (CFU), live/dead assay, biomass via crystal violet staining, and polysaccharide production by biofilms were determined on composites. Result Adding 3% DMAHDM to composite did not affect the flexure strength and elastic modulus (p > 0.1). For all six species of periodontal pathogens, the DMAHDM composite had biofilm CFU nearly three orders of magnitude less than that without DMAHDM. The killing efficacy of DMAHDM composite against the six species was: E. faecalis < F. nucleatum < P. nigrescens = P. intermedia < A. actinomycetemcomitans < P. gingivalis . Biofilm biomass and polysaccharide were also greatly reduced via DMAHDM (p < 0.05). Significance The novel nanocomposite containing DMAHDM and NACP showed strong inhibiting effect against all six species of periodontitis-related pathogens. This composite is promising for Class V restorations to restore root caries and combat periodontitis. [ABSTRACT FROM AUTHOR]

The objectives of this study were to investigate the effects of dental adhesives containing quaternary ammonium methacrylates (QAMs) with different alkyl chain lengths (CL) on ecological caries prevention in vitro. Five QAMs were synthesized with a CL = 3, 6, 9, 12, and 16 and incorporated into adhesives. Micro-tensile bond strength and surface charge density were used to measure the physical properties of the adhesives. The proportion change in three-species biofilms consisting of Streptococcus mutans, Streptococcus sanguinis, and Streptococcus gordonii was tested using the TaqMan real-time polymerase chain reaction. Lactic acid assay, MTT [3-(4,5-dimethyl-thiazol-2-yl)-2,5-diphenyltetrazolium bromide] assay, exopolysaccharide staining, live/dead staining, scanning electron microscopy (SEM), and transverse microradiography (TMR) were performed to study the anti-biofilm and anti-demineralization effects of the dental adhesives. The results showed that incorporating QAMs with different alkyl chain lengths into the adhesives had no obvious effect on the dentin bond strength. The adhesives containing QAMs with a longer alkyl chain developed healthier biofilms. The surface charge density, anti-biofilm, and anti-demineralization effects of the adhesives increased with a CL of the QAMs from 3 to 12, but decreased slightly with a CL from 12 to 16. In conclusion, adhesives containing QAMs with a tailored chain length are promising for preventing secondary caries in an “ecological way”. [ABSTRACT FROM AUTHOR]

The prevalence of stomatitis, especially caused by Candida albicans, has highlighted the need of new antifungal denture materials. This study aimed to develop an antifungal heat-curing resin containing quaternary ammonium monomer (dimethylaminododecyl methacrylate, DMADDM), and evaluate its physical performance and antifungal properties. The discs were prepared by incorporating DMADDM into the polymer liquid of a methyl methacrylate-based, heat-polymerizing resin at 0% (control), 5%, 10%, and 20% (w/w). Flexure strength, bond quality, surface charge density, and surface roughness were measured to evaluate the physical properties of resin. The specimens were incubated with C. albicans solution in medium to form biofilms. Then Colony-Forming Units, XTT assay, and scanning electron microscope were used to evaluate antifungal effect of DMADDM-modified resin. DMADDM modified acrylic resin had no effect on the flexural strength, bond quality, and surface roughness, but it increased the surface charge density significantly. Meanwhile, this new resin inhibited the C. albicans biofilm significantly according to the XTT assay and CFU counting. The hyphae in C. albicans biofilm also reduced in DMADDM-containing groups observed by SEM. DMADDM modified acrylic resin was effective in the inhibition of C. albicans biofilm with good physical properties. [ABSTRACT FROM AUTHOR]

Objective The aim of this study was to investigate antibiofilm effects of a recently developed glass ionomer cement (GIC) containing dimethylaminododecyl methacrylate (DMADDM) under oral conditions. Methods Biofilms were allowed to form in situ on GIC specimens ( n = 216) which contained DMADDM (1.1 wt.% or 2.2 wt.%). Samples without DMADDM served as control ( n = 108). GIC specimens were fixed on custom made splints and exposed to the oral cavity in six healthy volunteers for 24, 48 and 72 h, respectively. Biofilm viability and coverage were analyzed by fluorescence microscopy (FM) and evaluated by red/green ratios and an established scoring system. Bacterial morphology and biofilm accumulation were determined by scanning electron microscopy (SEM). Additionally, material properties as surface charge density of quaternary ammonium groups, surface roughness and DMADDM release were recorded. Results FM results showed a higher ratio (24 h: 0%: 0.5, 1.1%: 1.2, 2.2%: 2.5) of red/green fluorescence on GIC samples containing DMADDM. Biofilm coverage and viability scores were significantly reduced (24 h: q1/median/q3 for: 0%: 3/4/5, 1.1%: 2/3/3, 2.2%: 1/2/2) on DMADDM containing samples compared to controls after 24 h as well as 48 and 72 h in situ ( p < 0.05). While surface charge density of quaternary ammonium groups and DMADDM release increased with the DMADDM concentration, surface roughness was lowest on specimens containing 2.2 wt.% DMADDM. Significance An in situ dental biofilm model was used to evaluate the novel GIC containing DMADDM. This material strongly inhibited biofilms in situ and is promising to prevent bacterial colonization on the surface of restorations. [ABSTRACT FROM AUTHOR]

Antibacterial bonding agents and composites containing dimethylaminododecyl methacrylate (DMADDM) have been recently developed. The objectives of this study were to investigate the antibacterial effect of novel adhesives containing different mass fractions of DMADDM on Streptococcus mutans (S. mutans) biofilm at different developmental stages. Different mass fractions of DMADDM were incorporated into adhesives and S. mutans biofilm at different developmetal stages were analyzed by MTT assays, lactic acid measurement, confocal laser scanning microscopy and scanning electron microscopy observations. Exopolysaccharides (EPS) staining was used to analyze the inhibitory effect of DMADDM on the biofilm extracellular matrix. Dentin microtensile strengths were also measured. Cured adhesives containing DMADDM could greatly reduce metabolic activity and lactic acid production during the development of S. mutans biofilms (p < 0.05). In earlier stages of biofilm development, there were no significant differences of inhibitory effects between the 2.5% DMADDM and 5% DMADDM group. However, after 72 h, the anti-biofilm effects of adhesives containing 5% DMADDM were significantly stronger than any other group. Incorporation of DMADDM into adhesive did not adversely affect dentin bond strength. In conclusion, adhesives containing DMADDM inhibited the growth, lactic acid production and EPS metabolism of S. mutans biofilm at different stages, with no adverse effect on its dentin adhesive bond strength. The bonding agents have the potential to control dental biofilms and combat tooth decay, and DMADDM is promising for use in a wide range of dental adhesive systems and restoratives. [ABSTRACT FROM AUTHOR]

Objectives: The objectives of this study were to develop bonding agent containing a new antibacterial monomer dimethylaminododecyl methacrylate (DMADDM) as well as nanoparticles of silver (NAg) and nanoparticles of amorphous calcium phosphate (NACP), and to investigate the effects of water-ageing for 6 months on dentine bond strength and antibiofilm properties for the first time. Methods: Four bonding agents were tested: Scotchbond Multi-Purpose (SBMP) Primer and Adhesive control; SBMP + 5% DMADDM; SBMP + 5% DMADDM + 0.1% NAg; and SBMP + 5% DMADDM + 0.1% NAg with 20% NACP in adhesive. Specimens were water-aged for 1 d and 6 months at 37 8C. Then the dentine shear bond strengths were measured. A dental plaque microcosm biofilm model was used to inoculate bacteria on water-aged specimens and to measure metabolic activity, colony-forming units (CFUs), and lactic acid production. Results: Dentine bond strength showed a 35% loss in 6 months of water-ageing for SBMP control (mean sd; n = 10); in contrast, the new antibacterial bonding agents showed no strength loss. The DMADDM-NAg-NACP containing bonding agent imparted a strong antibacterial effect by greatly reducing biofilm viability, metabolic activity and acid production. The biofilm CFU was reduced by more than two orders of magnitude, compared to SBMP control. Furthermore, the DMADDM-NAg-NACP bonding agent exhibited a long-term antibacterial performance, with no significant difference between 1 d and 6 months ( p > 0.1). Conclusions: Incorporating DMADDM-NAg-NACP in bonding agent yielded potent and longlasting antibacterial properties, and much stronger bond strength after 6 months of waterageing than a commercial control. The new antibacterial bonding agent is promising to inhibit biofilms and caries at the margins. The method of DMADDM-NAg-NACP incorporation may have a wide applicability to other adhesives, cements and composites [ABSTRACT FROM AUTHOR]

Secondary caries often occurs at the tooth-composite margins. This study developed a novel bioactive composite containing DMAHDM (dimethylaminohexadecyl methacrylate) and NACP (nanoparticles of amorphous calcium phosphate), inhibiting caries at the enamel restoration margins in an in vitro saliva-derived biofilm secondary caries model for the first time. Four composites were tested: (1) Heliomolar nanocomposite, (2) 0% DMAHDM + 0% NACP, (3) 3% DMAHDM + 0% NACP, (D) 3% DMAHDM + 30% NACP. Saliva-derived biofilms were tested for antibacterial effects of the composites. Bovine enamel restorations were cultured with biofilms, Ca and P ion release of nanocomposite and enamel hardness at the enamel restoration margins was measured. Incorporation of DMAHDM and NACP into composite did not affect the mechanical properties (p > 0.05). The biofilms' CFU (colony-forming units) were reduced by 2 logs via DMAHDM (p < 0.05). Ca and P ion release of the nanocomposite was increased at cariogenic low pH. Enamel hardness at the margins for DMAHDM group was 25% higher than control (p < 0.05). With DMAHDM + NACP, the enamel hardness was the greatest and about 50% higher than control (p < 0.05). Therefore, the novel composite containing DMAHDM and NACP was strongly antibacterial and inhibited enamel demineralization, resulting in enamel hardness at the margins under biofilms that approached the hardness of healthy enamel. [ABSTRACT FROM AUTHOR]

Cariogenic oral biofilms are strongly linked to dental caries around dental sealants. Quaternary ammonium monomers copolymerized with dental resin systems have been increasingly explored for modulation of biofilm growth. Here, we investigated the effect of dimethylaminohexadecyl methacrylate (DMAHDM) on the cariogenic pathogenicity of Streptococcus mutans (S. mutans) biofilms. DMAHDM at 5 mass% was incorporated into a parental formulation containing 20 mass% nanoparticles of amorphous calcium phosphate (NACP). S. mutans biofilms were grown on the formulations, and biofilm inhibition and virulence properties were assessed. The tolerances to acid stress and hydrogen peroxide stress were also evaluated. Our findings suggest that incorporating 5% DMAHDM into 20% NACP-containing sealants (1) imparts a detrimental biological effect on S. mutans by reducing colony-forming unit counts, metabolic activity and exopolysaccharide synthesis; and (2) reduces overall acid production and tolerance to oxygen stress, two major virulence factors of this microorganism. These results provide a perspective on the value of integrating bioactive restorative materials with traditional caries management approaches in clinical practice. Contact-killing strategies via dental materials aiming to prevent or at least reduce high numbers of cariogenic bacteria may be a promising approach to decrease caries in patients at high risk. [ABSTRACT FROM AUTHOR]