Search

The carbon capture, utilization and storage (CCUS) technique is widely applied in order to solve energy shortages and global warming, in which CO2 storage plays an important part. Herein, the CO2 storage in reservoir pores with a dead-end is investigated using a molecular dynamics simulation. The results indicate that, when a CO2 molecule flows through a reservoir pore towards its dead-end, it is readily captured inside said dead-end. When the pressure difference of the CO2 injection increases, the transport speed of the CO2 becomes faster, and the storage efficiency increases. The rate constants for the absorption of the carbon dioxide at 5 MPa, 10 MPa, and 15 MPa are 0.47 m/s, 2.1 m/s, and 3.1 m/s. With the same main channel, a narrower dead-end with less oil molecules would cause a smaller spatial potential resistance, which would lead to a faster CO2 replacement and storage process. The 3 nm main channel with a 1.5 nm dead-end model had the highest absorption rate of 5.3 m/s out of the three sets of models with different dead-ends. When the dead-end's width was constant, the rate constants for the absorption of carbon dioxide in the 6 nm main channel with a 1.5 nm dead-end model was 1.8 m/s, which was higher than that of the 3 nm–1.5 nm model. This study investigates the mechanism of CO2 storage in reservoir pores with a dead-end at the molecular level and provides a scientific basis for the practical application of CO2 storage. [ABSTRACT FROM AUTHOR]

The occurrence state of oil, gas, and water plays a crucial role in exploring shale reservoirs. In this study, molecular dynamics simulations were used to investigate the occurrence states of these fluids in shale nanopores. The results showed that when the alkane is light oil, in narrow pores with a width less than 3 nm, oil molecules exist only in an adsorbed state, whereas both adsorbed and free states exist in larger pores. Due to the stronger interaction of water with the rock surface, the adsorption of oil molecules near the rock is severely prohibited. Oil/water/gas occurrence characteristics in the water-containing pore study indicate that CO2 gas can drive free oil molecules out of the pore, break water bridges, and change the occurrence state of water. During displacement, the gas type affects the oil/gas occurrence state. CO2 has strong adsorption capacity, forming a 1.45 g/cm3 adsorption layer on the rock surface, higher than oil's density peak of 1.29 g/cm3. Octane solubility in injected gases is CO2 (88.1%) > CH4 (76.8%) > N2 (75.4%), with N2 and CH4 having weak competitive adsorption on the rock. The investigation of different shale reservoir conditions suggests that at high temperature or low pressure, oil/gas molecules are more easily displaced, while at low temperature or high pressure, they are tightly adsorbed to the reservoir rock. These findings contribute to the understanding of fundamental mechanisms governing fluid behavior in shale reservoirs, which could help to develop proper hydrocarbon recovery methods from different oil reservoirs. [ABSTRACT FROM AUTHOR]

Because of the growing demand for energy, oil extraction under complicated geological conditions is increasing. Herein, oil displacement by CO2 in wedge-shaped pores was investigated by molecular dynamics simulation. The results showed that, for both single and double wedge-shaped models, pore Ⅱ (pore size from 3 to 8 nm) exhibited a better CO2 flooding ability than pore Ⅰ (pore size from 8 to 3 nm). Compared with slit-shaped pores (3 and 8 nm), the overall oil displacement efficiency followed the sequence of 8 nm > double pore Ⅱ > single pore Ⅱ > 3 nm > double pore Ⅰ > single pore Ⅰ, which confirmed that the exits of the wedge-shaped pores had determinant effects on CO2 enhanced oil recovery over their entrances. "Oil/CO2 inter-pore migration" and "siphoning" phenomena occurred in wedge-shaped double pores by comparing the volumes of oil/CO2 and the center of mass. The results of the interaction and radial distribution function analyses indicate that the wide inlet and outlet had a larger CO2–oil contact surface, better phase miscibility, higher interaction, and faster displacement. These findings clarify the CO2 flooding mechanisms in wedge-shaped pores and provide a scientific basis for the practical applications of CO2 flooding. [ABSTRACT FROM AUTHOR]