Search

Oil shale is a potential strategic resource with large reserves and widespread application potential, and in situ combustion is an effective method to exploit oil shale. However, the interaction mechanism between pyrolysis and combustion reaction is still not clear; hence, the evolution of components and temperature in the reservoir is hard to describe, limiting the application of in situ combustion in oil shale. In this paper, we established a comprehensive reactive flow model to describe the in situ combustion in oil shale, and the in situ combustion process is analyzed in detail. During the in situ combustion, only pyrolysis reactions occur in the matrix system, while combustion reactions only occur in the fracture system. Under the interaction mechanisms of these two kinds of chemical reactions, in situ combustion upgrading can be carried out continuously. The produced oil and hydrocarbon gas per unit volume of oil shale are 0.06 m3/m3 and 12.5 m3/m3 , respectively, but about 83.3 m3/m3 of CO2 is produced that needs to be stored subsequently when air is directly injected into the reservoir to maintain the combustion reactions. Increasing oil content and air injection rate can increase the cumulative oil and gas production, but there are optimal values above which the increase rate slows down. The energy conversion efficiency of in situ combustion is 49.5, and it is much higher than the energy conversion efficiency in other in situ upgrading methods for oil shale. [ABSTRACT FROM AUTHOR]

Abstract In-situ conversion process (ICP) can be an effective technique for the development of oil shale and ultra heavy oils, in which kerogen or heavy components will be cracked into light oils and gases via underground heating and pyrolysis, and the retorted oil can be recovered via conventional extraction techniques. Heating of targeted formation can be conducted using electrical heaters installed in vertical or horizontal wells, while a slow heating rate and lack of driving energy for oil production are the main issues of the conventional in-situ conversion process. In this study, an innovative nitrogen injection assisted in-situ conversion process (NAICP) was proposed to increase formation heating rate and improve oil production from oil shale. Reaction models of kerogen pyrolysis at elevated temperature were established, along with models for the evolution of porosity and permeability of oil shale formation during the pyrolysis process. The performance of nitrogen injection on the effectiveness of the ICP was then investigated through reservoir numerical simulation. The simulation results show that additional nitrogen injection can improve the heating rate of the oil shale formation, enhance oil production and energy efficiency in comparison with the conventional ICPs, which can be attributed to enhanced heat convection, pressurization effect and gas driving mechanism. Nitrogen injection assisted in-situ conversion process can be a promising technique for the exploitation of oil shale. Highlights • Nitrogen injection assisted in-situ process for oil shale was proposed. • The advantages of nitrogen injection assisted in-situ process were studied. • The mechanism of nitrogen injection to improve oil production performance was studied. • The effects of heating temperature and nitrogen injection rate were studied. [ABSTRACT FROM AUTHOR]

In-situ upgrading (ISU) via downhole heating is an innovative and efficient technique for oil shale and ultra heavy oil recovery. However, low heat transfer in the ISU process can limit its application in large scale. Therefore, efficient air injection assisted ISU process (AAISU) was proposed. In this study, reservoir stimulation of the AAISU process was performed to investigate the effect of air injection on heat transfer, oil production performance and energy conversion efficiency, as compared to the original ISU process. The influences of important engineering aspects were investigated, including well pattern, well distance, heating temperature and air injection rate for the field application of the AAISU technique. The reservoir stimulation results indicate that heat transfer rate can be significantly accelerated by air injection, and the average reservoir temperature during the AAISU can be increased to 250 °C after one year, in comparison with that of 116 °C in the ISU process. The contribution of air injection on the total heat transfer can be approached to 60%. Air injection can also enhance oil recovery and improve the energy efficiency. Heating temperature and air injection rate also have significant impact on the performance of the AAISU process. For a 15 m × 15 m × 10 m geo-model, increase of the heating temperature from 250 °C to 350 °C and air injection rate from 500 m3/day to 1000 m3/day can result in improved energy efficiency. However, heating temperature above 350 °C and the air injection rate over 1000 m3/day can led to a decreased energy efficiency, due to higher energy consumption on electrical heating and high rate of air injection. • Air injection assisted in situ upgrading process (AAISU) of ultra heavy oils was proposed. • The effect of air injection on heat transfer was studied. • The influence of well pattern and well distance on the AAISU was investigated. • The influence of heating temperature and air injection rate on the AAISU process was evaluated. [ABSTRACT FROM AUTHOR]