Search

The use of optical fibers is increasing in modern aircraft because this helps solve challenges of size, weight, communication, and reliability in new generation aircraft. This study describes a video and power transmission system using optical fibers (PoF) for in-flight entertainment (IFE) system application. We present the benefits and the limitations of this application, and we perform two practical experiments to demonstrate their performance. We used off-the-shelf devices in the experiments, such as one 15-Watt semiconductor laser operating at 808 nm, GaAs photovoltaic converters, optical transmitters and receivers, and video monitors. The power and video signals were transmitted using two 50-m length multimode fibers. In addition, we proposed and tested two types of energy transformation units (ETUs), which are responsible for supplying electrical energy to the IFE video monitor and the optical fiber receiver. [ABSTRACT FROM AUTHOR]

In this paper, we proposed a sealing method of fiber Bragg grating (FBG) in pressure sensors using electroless nickel-plating. The sensor is designed to be used in harsh environments of thermoelectric power plant engines. In order to be applied in the engine injector nozzle, the FBG has just a single attached point in the pressure sensor and the combustion chamber pressure will freely compress the FBG. The fixation material used to seal the FBG in the pressure sensor is the key for the sensor performance considering the engine environment used in thermoelectric power plant. Typical level of pressure in the engine monitoring point is around 200 bar and the temperature exceeds 300 °C. We detailed the method of fabrication and the characteristics of this method. Next, the FBG pressure sensors using electroless nickel-plating sealing were studied and submitted to laboratorial and field trial evaluation. In addition, we evaluated the signal characteristics of the FBG pressure sensor and we compared it with a standard pressure sensor used in this application. [ABSTRACT FROM AUTHOR]

This paper described a distributed temperature sensing (DTS) system based on Raman scattering using pre-shaped simplex code (S code) with erbium-doped fiber amplifiers (EDFAs) transient effects suppression techniques. We investigated these techniques to mitigate the waveform distortion caused by the EDFA when DTS uses S code in an optical time-domain reflectometer (OTDR). We tested the DTS experimentally using two EDFA’s transient effects suppression techniques: automatic gain control and pre-shaped S code pulses. The performance of these two techniques working simultaneously was compared with the standard S code technique. In the experimental setup, we tested code word lengths from 3 to 127 b with 100-ns pulsewidth. The temperature measurement demonstration was done in reaches of 40 and 50 km, and in a repeated system of 62 km using standard single-mode fiber and commercial OTDR and EDFA modules, which were properly adapted to this application. Results show that EDFA’s transient effects suppression techniques allow increasing the reach of DTS using short S code sequences, reducing the complexity and the processing time. [ABSTRACT FROM PUBLISHER]

In this work we propose the use of power over fiber (PoF) and free space optics (FSO) techniques to powering and receive signals from an electrical current sensor placed at high voltage potential using a pair of optical collimators. The technique evaluation was performed in a laboratorial prototype using 62.5/125 μm multimode fiber to study the sensitivity of the optical alignment and the influence of the collimation process in the sensing system wavelengths: data communication (1310 nm) and powering (830 nm). The collimators were installed in a rigid electric insulator in order to maintain the stability of transmission. [ABSTRACT FROM AUTHOR]

This paper presents the results of a quantitative and qualitative monitoring system for switchgear with full electrical isolation using fiber-optic technology that aims to help in the automation of substations. The remote sensors were installed near each phase of the switchgear and they are powered only by the optical power provided by one pair of optic fibers connected to a remote optical source. At the same time, part of the optical supply power is used to measure the contact quality by using the optical triangulation method. Two microcameras installed in each remote sensor allow for the observation of the switchgear contact and hinge. All data are transmitted by the optical fibers to a control unit installed in the substation room, and from that, the data are transmitted to the utilities' operating center using the utilities commercial telecom optical network. We describe the system design, laboratory tests, and the field trial conducted in a 138-kV distribution substation. [ABSTRACT FROM AUTHOR]

In this work, we present the design, laboratory tests, and the field trial results of a power-over-fiber (PoF) low power instrument transformer (LPIT) for voltage and current measurements in the medium voltage distribution networks. The new proposed design of this power-over-fiber LPIT aims to overcome the drawbacks presented by the previous technologies, such as the continuous operation (measuring and data transmission) for a wide current range conducted in the medium voltage transmission lines, damage due to lightning strikes, accuracy dependency on vibration, position and temperatures. The LPIT attends the accuracy criteria of IEC 61869-10 and IEC 61869-11 in terms of current and voltage accuracy and it attends the practical criteria adopted by Utilities companies including voltage measurements without removing the coating of the covered conductors. The PoF based LPIT was developed to be applied at 11.9 kV, 13.8 kV, and 23.0 kV phase-to-phase nominal voltages, and in two current ranges 1.25–30 A and 37.5–900 A. The digital data transmission of current, voltage, and temperature from the sensing unit to the processing unit uses a special synchronism technique and it is performed by two 62.5 µm multimode fibers in 850 nm. The optical powering in 976 nm is also performed by one 62.5 µm multimode fiber from the processing unit to the sensor unit. We presented all details of the sensor design and its laboratory characterization in terms of accuracy and temperature correction. We also presented the results of field tests of the sensor made in two different conditions: in a standard distribution network and an experimental hybrid fiber/power distribution network. We believe that these studies aim to incorporate optical fiber and devices, digital technologies, communications systems in electrical systems driving their evolution. [ABSTRACT FROM AUTHOR]

• Application of hollow-core photonic crystal fibers in Power-over-Fiber context; • Valid route for new PoF systems potentially able to circumvent silica-fibers limitations; • Discussion on the prospects and related issues for HCPCF application in PoF. Research achievements in hollow-core photonic crystal fibers technology allow ascertaining such fibers as outstanding platforms for delivering high-power laser beams. Indeed, the key property underlying the success of this family of optical fibers for high-power beam delivery is their capability of efficiently transmitting light through empty space with minimal interaction with the fiber microstructure. In this context, here we widen the framework of hollow-core fiber-based beam delivery applications by demonstrating their utilization as promising platforms for Power-over-Fiber systems. Thus, we report on the use of a tubular-lattice hollow-core fiber to deliver a watt-level continuous-wave laser beam onto a photovoltaic converter and activate a representative camera circuit. We believe that the experiments reported herein allow identifying hollow-core fibers as eligible candidates for next-generation Power-over-Fiber devices potentially able to lift the power restrictions of current solid-core fiber-based Power-over-Fiber systems. [ABSTRACT FROM AUTHOR]