Search

Real time paper surface-web measurement is one of the challenging research fields. The traditional laboratory method has many limitations and is unable to measure the entire tambour during the manufacturing process. It has been necessary to develop an online technique that could measure the surface topography in real time. An optical technique was developed, based on laser triangulation, and is applied to develop a new prototype device, which characterizes high speed paper-web surfaces over a wide scale of spatial wavelengths spectrum and computes the surface roughness in real time. The used multi channel pulsed laser diode, source of illumination onto the paper-web, is of benefit due to its low coherence length and is capable to deliver a powerful burst of light beam over a 1 µs duration, which delivers energy of 100 µJ per pulse. The short exposure time avoids blurriness in the acquired images which could possible due to the high speed and vibrations on the paper-web.The laser beam is shaped into a narrow line-of-light using cylindrical lenses and is projected onto a paper-web surface, which covers a physical length of about 210 mm. The created line-of-light cross section full width at half maximum, FWHM Gaussian distribution, is 2-3 pixels on the image. The line-of-light is projected onto the paper-web perpendicular to the plane of the surface. The low angled, low specular, reduced coherence length, scattered reflected laser line is captured by the 3 CCD sensors, which are synchronized with the laser source. The low specular light ensures to avoid saturation of the imaging sensors if the surface is very smooth, and obliquely captures the z-directional fine feature of the surface.The scattered phenomenon of the reflected light is responsible for the surface irregularity measurements. The basic image processing algorithm is applied in order to remove noise and cropped the images widthwise so that only pixels above a preset threshold gray level can be processed, which enables efficient real time measurement. The image is transformed into a 1D array using the center of gravity, COG. The accuracy and precision of the COG depends on the line-of-light FWHM, which, in turn, is responsible for the accuracy, noise and the resolution of the developed technique. The image subpixel resolution achieved is 0.01 times a pixel and uuncertainty in the raw data is 0.43 µm while it is 0.05 µm in the rms roughness.The signal processing steps combining the B-Spline filter and the filter in the spatial frequency domain were employed in order to separate roughness, waviness, and form and position error in the raw profile. The prototype is designed to measure online surface roughness and to characterize surface in a spatial wavelength spectrum from 0.09 to 30 mm, which is extendable to any required spatial range in order to cover a wide scale surface feature such as micro roughness, macro roughness and waviness. It is proven that exploitation of a simple laser triangulation technique could lead to an improvement in the overall quality and efficiency in the paper and paperboard industries and it can also be of potential interest for the other surface characterization problems.

Real time surface topography measurement in the paper and paperboard industries is a challenging research field. The existing online techniques measure only a small area of paper surface and estimate topographical irregularities in a narrow scale as a single predictor. Considering the limitations and complications in measuring the surface at high speed, a laser line triangulation technique is explored to measure surface topography in a wide scale. The developed technique is new for the paper and paperboard application that scans a line onto the paper-web surface up to 210 mm in length in the cross machine direction. The combination of a narrow laser linewidth imaging, a subpixel resolution, and the selection of a unique measurement location has made it possible to measure roughness and simultaneously characterize paper surface topography from 0.1 to 30 mm spatial wavelength. This spatial range covers wide scale surface properties such as roughness, cockling, and waviness. The technique clearly distinguishes and characterizes the surface of newspaper, and lightweight coated, coated, and uncoated paperboard in real time during the paper manufacturing process. The system temporal noise for the average roughness is estimated as 37 dB. The signal to noise ratio found is from 5.4 to 8.1 in the short spatial wavelength up to 1 mm, whereas it is more than 75 in the long spatial wavelength from 5 to 10 mm.

Real time paper surface-web measurement is one of the challenging research fields. The traditional laboratory method has many limitations and is unable to measure the entire tambour during the manufacturing process. It has been necessary to develop an online technique that could measure the surface topography in real time. An optical technique was developed, based on laser triangulation, and is applied to develop a new prototype device, which characterizes high speed paper-web surfaces over a wide scale of spatial wavelengths spectrum and computes the surface roughness in real time. The used multi channel pulsed laser diode, source of illumination onto the paper-web, is of benefit due to its low coherence length and is capable to deliver a powerful burst of light beam over a 1 µs duration, which delivers energy of 100 µJ per pulse. The short exposure time avoids blurriness in the acquired images which could possible due to the high speed and vibrations on the paper-web.The laser beam is shaped into a narrow line-of-light using cylindrical lenses and is projected onto a paper-web surface, which covers a physical length of about 210 mm. The created line-of-light cross section full width at half maximum, FWHM Gaussian distribution, is 2-3 pixels on the image. The line-of-light is projected onto the paper-web perpendicular to the plane of the surface. The low angled, low specular, reduced coherence length, scattered reflected laser line is captured by the 3 CCD sensors, which are synchronized with the laser source. The low specular light ensures to avoid saturation of the imaging sensors if the surface is very smooth, and obliquely captures the z-directional fine feature of the surface.The scattered phenomenon of the reflected light is responsible for the surface irregularity measurements. The basic image processing algorithm is applied in order to remove noise and cropped the images widthwise so that only pixels above a preset threshold gray level can be processed, which enables efficient real time measurement. The image is transformed into a 1D array using the center of gravity, COG. The accuracy and precision of the COG depends on the line-of-light FWHM, which, in turn, is responsible for the accuracy, noise and the resolution of the developed technique. The image subpixel resolution achieved is 0.01 times a pixel and uuncertainty in the raw data is 0.43 µm while it is 0.05 µm in the rms roughness.The signal processing steps combining the B-Spline filter and the filter in the spatial frequency domain were employed in order to separate roughness, waviness, and form and position error in the raw profile. The prototype is designed to measure online surface roughness and to characterize surface in a spatial wavelength spectrum from 0.09 to 30 mm, which is extendable to any required spatial range in order to cover a wide scale surface feature such as micro roughness, macro roughness and waviness. It is proven that exploitation of a simple laser triangulation technique could lead to an improvement in the overall quality and efficiency in the paper and paperboard industries and it can also be of potential interest for the other surface characterization problems.

Real time paper surface-web measurement is one of the challenging research fields. The traditional laboratory method has many limitations and is unable to measure the entire tambour during the manufacturing process. It has been necessary to develop an online technique that could measure the surface topography in real time. An optical technique was developed, based on laser triangulation, and is applied to develop a new prototype device, which characterizes high speed paper-web surfaces over a wide scale of spatial wavelengths spectrum and computes the surface roughness in real time. The used multi channel pulsed laser diode, source of illumination onto the paper-web, is of benefit due to its low coherence length and is capable to deliver a powerful burst of light beam over a 1 µs duration, which delivers energy of 100 µJ per pulse. The short exposure time avoids blurriness in the acquired images which could possible due to the high speed and vibrations on the paper-web.The laser beam is shaped into a narrow line-of-light using cylindrical lenses and is projected onto a paper-web surface, which covers a physical length of about 210 mm. The created line-of-light cross section full width at half maximum, FWHM Gaussian distribution, is 2-3 pixels on the image. The line-of-light is projected onto the paper-web perpendicular to the plane of the surface. The low angled, low specular, reduced coherence length, scattered reflected laser line is captured by the 3 CCD sensors, which are synchronized with the laser source. The low specular light ensures to avoid saturation of the imaging sensors if the surface is very smooth, and obliquely captures the z-directional fine feature of the surface.The scattered phenomenon of the reflected light is responsible for the surface irregularity measurements. The basic image processing algorithm is applied in order to remove noise and cropped the images widthwise so that only pixels above a preset threshold gray level can be processed, which enables efficient real time measurement. The image is transformed into a 1D array using the center of gravity, COG. The accuracy and precision of the COG depends on the line-of-light FWHM, which, in turn, is responsible for the accuracy, noise and the resolution of the developed technique. The image subpixel resolution achieved is 0.01 times a pixel and uuncertainty in the raw data is 0.43 µm while it is 0.05 µm in the rms roughness.The signal processing steps combining the B-Spline filter and the filter in the spatial frequency domain were employed in order to separate roughness, waviness, and form and position error in the raw profile. The prototype is designed to measure online surface roughness and to characterize surface in a spatial wavelength spectrum from 0.09 to 30 mm, which is extendable to any required spatial range in order to cover a wide scale surface feature such as micro roughness, macro roughness and waviness. It is proven that exploitation of a simple laser triangulation technique could lead to an improvement in the overall quality and efficiency in the paper and paperboard industries and it can also be of potential interest for the other surface characterization problems.

The introduction of energy resolution in X-ray image detectors will lead to tradeoffs between circuit complexity and spatial/energy resolution in the pixel design. The proposed method provides continuous energy resolution with only two energy channels per pixel, which is a comparable complexity to that of a window discriminator pixel like Medipix2. The paper illustrates the method and validates the method through analytical analysis and through simulation of real and synthetic data.

A method, generally called oversampling, to reach sub-pixel resolution by taking slightly displaced images of an object is investigated for X-ray applications. By mounting the sensor on a high prec ...

X-ray imaging has been used extensively in the manufacturing industry. In the paper and paperboard industry X-ray imaging has been used for measuring parameters such as coat weight, using mean valu ...

Recent advancements in the grating interferometer based Phase Contrast X-ray Imaging (PCXI) technique enables high quality dark-field images to be obtained using conventional X-ray tubes. The dark-field images map the scattering inhomogeneities inside objects. Since, the dark-field image is constructed by considering only those photons which are scattered while passing through the objects, it can reveal useful information about the object inner structures, such as, the fibre structures inside paperboards. The end-use performance of paperboards, such as the printing quality and the stiffness depends on the uniformity in the thickness and the structures of the coating layer of the paperboards. The uniformity in the coating layer is determined by the coating techniques, the coating materials and the topography of the base sheet. In this article, the dark-field signals from four paperboard samples with different quality indices are analysed. The isotropic and the anisotropic scattering coefficients for all of the samples have been calculated. Based on the correlation between the isotropic coefficients and the quality indices of the paperboards, a new method for paperboard quality measurement has been suggested.

X-ray imaging systems such as photon counting pixel detectors have a limited spatial resolution of the pixels, based on the complexity and processing technology of the readout electronics. For X-ra ...