Search

Increasing the penetration level of distributed generation (DG) may lead to improper protection coordination. Previous work introduced a protection coordination index (PCI) that can quantify the impact of installing a DG at individual locations. This paper extends on previous work and proposes a generalized approach for calculating PCI considering multiple DG locations simultaneously. Furthermore, this paper proposes a solution for enhancing the PCI using fault current limiters (FCL). The problem is formulated as a mixed-integer nonlinear programming problem to determine the optimal FCL size and location as well as enhanced PCI. [ABSTRACT FROM AUTHOR]

In this paper, a new formulation for distribution system reconfiguration (DSR) is proposed for minimizing the annual energy losses considering the variability in active and reactive power demand and distributed generation (DG) profiles. A fuzzy C-means clustering algorithm is used to obtain representative centroids from annual DG and power demand profiles. The DSR study is formulated as a mixed-integer nonlinear programming optimization problem and tested on a 33-bus and an 84-bus system. The minimization is subject to the power balance, bus voltage, and distribution system radiality constraints. Using this formulation, a single optimum configuration that minimizes annual energy losses is found and shown to be different from the optimum configuration, found in previous literature, which focuses on minimizing power losses at peak or average loads. In addition, the prospective advantages of grid automation on DSR are demonstrated to provide further energy loss reduction by including the possibility of interchanging a predefined number of configurations that minimize annual energy losses. [ABSTRACT FROM AUTHOR]

With the integration of distributed generation (DG) to meshed distribution systems, the operating time of the protective system becomes a major concern in order to avoid nuisance DG tripping. This paper proposes a new time–current–voltage tripping characteristic for directional overcurrent relays (DOCRs) that can achieve a higher possible reduction of overall relays operating time in meshed distribution networks. The proposed tripping characteristic is described in detail. Moreover, the protection coordination problem is formulated as a constrained nonlinear programming problem to determine the optimal relay settings. The proposed characteristic is tested on the power distribution system of the IEEE 14 bus and IEEE 30 bus with inverter-based and synchronous-based DG units. The outcome of this study reveals that the new tripping characteristic for DOCRs achieves notable reduction in total relays' operating time over the conventional characteristic. [ABSTRACT FROM AUTHOR]

In the presence of distributed generation (DG), it is important to assure a fast and reliable protection system for the distribution network to avoid unintentional DG disconnection during fault conditions. In this paper, dual setting directional over-current relays are proposed for protecting meshed distribution systems with DG. Dual setting relays are equipped with two inverse time-current characteristics whose settings will depend on the fault direction. The protection coordination problem for the dual setting directional relay is formulated as a nonlinear programming problem where the objective is to minimize the overall time of operation of relays during primary and backup operation. The proposed protection coordination scheme using dual setting relays is compared against the conventional approach, which relies on the conventional one setting directional relay. The proposed scheme is applied to the power distribution network of the IEEE 30-bus system equipped with synchronous and inverter-based DG. The results show that the proposed protection coordination scheme with dual setting relay can significantly reduce the overall relay operating time, making it an attractive option for distribution systems with DG. [ABSTRACT FROM PUBLISHER]

Depending on the capacity, type and location, distributed generation (DG) can have an impact on protection coordination of directional over-current relays for looped distribution systems. In this paper, a new index is proposed, “protection coordination index” (PCI), which can serve as an effective measure when planning the protection of meshed distribution systems with DG. A two-phase non-linear programming (NLP) optimization problem is proposed to determine the PCI by optimally calculating variations in the maximum DG penetration level with changes in the protection coordination time interval. Furthermore, the influence of connecting a DG at a certain location on the system PCIs is examined. The presented analysis is tested on the distribution section of the IEEE 14-bus and IEEE 30-bus systems. The PCI can serve as an efficient index for distribution system planners: (i) to determine the best DG candidate locations for utility owned DG and (ii) to evaluate the impact of a customer owned DG, considering distribution system protection. [ABSTRACT FROM PUBLISHER]

In this paper, a new optimization problem is proposed to determine the maximum distributed generation (DG) penetration level by optimally selecting types, locations and sizes of utility owned DG units. The DG penetration level could be limited by harmonic distortion because of the nonlinear current injected by inverter-based DG units and also protection coordination constraints because of the variation in fault current caused by synchronous-based DG units. Hence the objective of the proposed problem is to maximize DG penetration level from both types of DG units, taking into account power balance constraints, bus voltage limits, total and individual harmonic distortion limits specified by the IEEE-519 standard, over-current relay operating time limits, and protection coordination constraints. The DG penetration study is formulated as a nonlinear programming (NLP) problem and tested on the IEEE-30 bus looped distribution network with ten load and DG scenarios. Similarly, feasibility assessment of customer owned DG unit installations considering power quality and protection coordination is also studied. Simulation results show the effectiveness of the proposed approach, which can serve as an efficient planning tool for utility operators. [ABSTRACT FROM PUBLISHER]

Microgrids can be operated either grid-connected to reduce system losses and for peak shaving or islanded to increase reliability and provide backup power during utility outage. Such dual configuration capability imposes challenges on the design of the protection system. Fault current magnitudes will vary depending on the microgrid operating mode. In this paper, a microgrid protection scheme that relies on optimally sizing fault current limiters and optimally setting directional overcurrent relays is proposed. The protection scheme is optimally designed taking into account both modes of operation (grid-connected and islanded). The problem has been formulated as a constrained nonlinear programming problem and is solved using the genetic algorithm with the static penalty constraint-handling technique. The proposed approach is tested on two medium-voltage networks: a typical radial distribution system and on the IEEE 30-bus looped power distribution system equipped with directly connected conventional synchronous generators. [ABSTRACT FROM PUBLISHER]

This paper presents an optimization procedure that enables the optimal dispatching of distributed generators and storage systems in a medium-voltage islanded microgrid. The network is assumed to be supplied by programmable (dispatchable) and nonprogrammable generators (i.e. nondispatchable, such as renewable energy sources—based units). The optimization goal is to minimize the overall microgrid operating cost and the pollutants emission of the programmable generators, assuming that all of the power made available by the renewable generators (photovoltaic and wind systems) is either directly injected into the network or stored in order to be subsequently delivered according to the proposed storage units' management strategy. The optimization is carried out by a niching evolutionary algorithm (NEA) that is able to find multiple optima and the variation of the objective function in their neighborhood. NEAs allow overcoming the performance of standard algorithms used for optimal power-flow calculations in power systems by avoiding falling into local optima. The optimization procedure is performed on a test microgrid and verified by computer simulations. The numerical results show that the solutions can always improve the microgrid performances irrespective of the network operating conditions in all of the considered cases. [ABSTRACT FROM AUTHOR]

Smart grids have become one of the important and challenging topics due to the numerous benefits it can bring to the power system. In this context, distributed generation (DG) is expected to play a significant role. The smart grid can have multiple configurations depending on the smart grid operating strategy and system conditions. In smart grids, DG could be operated either grid connected or islanded. Such flexible and variable configuration results in variable fault current levels which could impact the operation of the existing protective devices on the distribution system. In this paper, it is proposed to optimally size thyristor-controlled impedance (TCI) of both inductive and capacitive type to manage the fault current levels under different smart grid configurations. The salient benefit is to avoid damage and delayed operation of protective devices due to the variability in fault currents with synchronous-based DG. The problem is formulated as a nonlinear programming (NLP) problem and the optimum size and type of the TCI is determined using particle swarm optimization (PSO). Results show that by optimally locating and sizing TCI, fault current levels under various smart grid configurations can be managed and thus avoiding protective device coordination failure and damage. [ABSTRACT FROM PUBLISHER]

This article presents a method of reducing the expected value of the transmission loss for a specified range of source impedance values at different buses by using inductor-capacitor compensators where it is desired to maintain a given power factor at a specified value. The criterion is based on mean value estimation of source and load characteristics, which is enabled by sampling measurements performed on the examined electrical plant, as well as statistical analysis. The major attribute of the method is that, unlike conventional approaches, it guarantees convergence to the optimal solution. Finally, the contribution of the newly developed method is demonstrated in examples taken from previous publications. [ABSTRACT FROM AUTHOR]