Search

Background Head injury occurs in up to 47% of skiing or snowboarding injuries and is the predominant cause of death in these sports. In most existing literature reporting injury type and prevalence, head injury mechanisms are underreported. Thus, protective equipment design relies on safety evaluation test protocols that are likely oversimplified. This study aims to characterize severity and mechanism of head injuries suffered while skiing and snowboarding in a form appropriate to supplement existing helmet evaluation methods. Methods A 6-year, multicentre, retrospective clinical record review used emergency databases from two major trauma centres and Coroner's reports to identify relevant cases which indicated head impact. Records were investigated to understand the relationships between helmet use, injury type and severity, and injury mechanism. Descriptive statistics and odds ratios aided interpretation of the data. Findings The snow sport head injury database included 766 cases. “Simple fall”, “jump impact” and “impact with object” were the most common injury mechanisms while concussion was observed to be the most common injury type. Compared to “edge catch”, moderate or serious head injury was more common for “fall from height” (OR = 4.69; 95% CI = 1.44–16.23; P = 0.05), “jump impact” (OR = 3.18; 95% CI = 1.48–7.26; P = 0.01) and “impact with object” (OR = 2.44; 95% CI = 1.14–5.56; P = 0.05). Occipital head impact was associated with increased odds of concussion (OR = 7.46; 95% CI = 4.55–12.56; P = 0.001). Interpretation Snow sport head injury mechanisms are complex and cannot be represented through a single impact scenario. By relating clinical data to injury mechanism, improved evaluation methods for protective measures and ultimately better protection can be achieved.

To evaluate the biomechanical properties of the upper thoracic spine in anterior-posterior shear loading at various displacement rates. These data broaden our understanding of thoracic spine biomechanics and inform efforts to model the spine and spinal cord injuries. Seven T1-T2 thoracic functional spinal units were loaded non-destructively by a pure shear force up to 200 N, starting from a neutral posture. Tests were run in both posterior and anterior directions, at displacement rates of 1, 10, and 100 mm/s. The three-dimensional motion of the specimen was recorded at 1000 Hz. Individual and averaged load-displacement curves were generated and specimen stiffnesses were calculated. Due to a nonlinear response of the specimens, stiffness was defined separately for both the lower half and the upper half of the specimen range of motion. Specimens were significantly stiffer in the anterior direction than in the posterior direction, across all rates. At low displacements, the anterior stiffness averaged 230 N/mm, 76% higher than the low displacement posterior stiffness of 131 N/mm. At high displacements, anterior stiffness averaged 258 N/mm, 51% stiffer than the high displacement posterior stiffness of 171 N/mm. Shear displacement rate had a small effect on the load response, with the 100 mm/s rate causing a mildly stiffer response at low displacements in the anterior direction. Overall, the load-displacement response exhibited pseudo-quadratic behavior at 1 and 10 mm/s but became more linear at 100 mm/s. The shear stiffness in the upper thoracic spine is greatest in the anterior loading direction, being 51%-76% greater than posterior, most likely due to facet interactions. The effect of the shear displacement rate is low.

Background CT is considered the best method for vertebral fracture detection clinically, but its efficacy in laboratory studies is unknown. Therefore, our objective was to determine the sensitivity, precision, and specificity of high-resolution CT imaging compared to detailed anatomic dissection in an axial compression and lateral bending cervical spine biomechanical injury model. Methods 35 three-vertebra human cadaver cervical spine specimens were impacted in dynamic axial compression (0.5 m/s) at one of three lateral eccentricities (low 5% of the spine transverse diameter, middle 50%, high 150%) and two end conditions (19 constrained lateral translation and 16 unconstrained). All specimens were imaged using high resolution CT imaging (246 μm). Two clinicians (spine surgeon and neuroradiologist) diagnosed the vertebral fractures based on 34 discrete anatomical structures using both the CT images and anatomical dissection. Findings The sensitivity of CT was highest for fractures of the facet joint (59%) and vertebral endplate (57%), and was lowest for pedicle (13%) and lateral mass fractures (23%). The precision of CT was highest for spinous process fractures (83%) and lowest for pedicle (21%), uncinate process and lateral mass (both 23%) fractures. The specificity of CT exceeded 90% for all fractures. The Kappa value between the two reviewers was 0.52, indicating moderate agreement. Interpretation In this in vitro cervical spine injury model, high resolution CT scanning missed many fractures, notably those of the lateral mass and pedicle. This finding is potentially important clinically, as the integrity of these structures is important to clinical stability and surgical fixation planning.

Background Head-first impacts with an aligned cervical spine cause some of the most severe types of injuries due to the risk of fractures and associated spinal cord injury. Sports, such as football, mountain biking and horseback riding, contribute to the incidence of spinal cord injury but there is potential to reduce the risk of these injuries through a helmet-mounted device. Methods A novel device, the Pro-Neck-Tor mechanism, was incorporated into a commercial football helmet and tested in head-first impact experiments. The Pro-Neck-Tor connects an inner and outer helmet shell, which upon head-first impact of a certain load, induces motion of the head away from the path of the following torso. Impacts were performed onto three impact surface angles with a flexion-inducing Pro-Neck-Tor mechanism. Findings Based on averaged data, the Pro-Neck-Tor provided a significant and consistent reduction in peak compressive neck forces compared to the unmodified football helmet in the conditions tested. In some impact conditions, the Pro-Neck-Tor increased the peak sagittal plane neck bending moments and impulse over that observed for the unmodified helmet. Interpretation The Pro-Neck-Tor with flexion escape is capable of lowering axial neck forces in head-first impacts compared to a conventional helmet by guiding the cervical column away from an aligned posture and into an eccentric loading scenario which published studies suggests frequently leads to no injury or to a less severe injury. Continued development and testing of the device are needed to optimize the altered neck loading and to drive the design toward a commercial configuration.

Cycling helmets often incorporate elements aimed to dissipate rotational energies, which is widely acknowledged to play a key role in concussion mechanics. In this study, we investigated the mechanics of an oblique helmet test protocol that induced helmet rotation while using it to evaluate the effectiveness of three helmet models: two standard expanded polystyrene helmets and a commercially-available helmet equipped with a liner designed to mitigate linear and rotational energies.Helmets equipped with WaveCel were tested against two expanded polystyrene helmet models through guided drops using a Hybrid III (HIII) head-and-neck surrogate. The three helmet models were tested across four impact conditions (n = 5) of different speeds and impact surface angles.Across all tests, a similar sequence of head motion was observed - first a flexion phase followed by an extension phase. The extension phase lacked evidence of biofidelity and was likely attributable to the energy stored in the neckform during the flexion phase; it was therefore neglected from analysis. Results showed WaveCel reduced the probability of AIS2 head injury across all tests (3 to 27% reductions in 4.8 m/s impacts; 36 to 37% reductions in 6.2 m/s impacts).The two-phased response of the HIII suggests that boundary condition selection can influence results and should thus be reported in studies using similar methods. While this protocol involved both axial and tangential impact components and were thus representative of real-world collisions, the efficacy of WaveCel should be further investigated through additional laboratory studies and tracking real-world cycling injury statistics.

During axial impact compression of the cervical spine, injury outcome is highly dependent on initial posture of the spine and the orientation, frictional properties and stiffness of the impact surface. These properties influence the “end condition” the spine experiences in real-world impacts. The effect of end condition on compression and sagittal plane bending in laboratory experiments is well-documented. The spine is able to escape injury in an unconstrained flexion-inducing end condition (e.g. against an angled, low friction surface), but when the end condition is constrained (e.g. head pocketing into a deformable surface) the following torso can compress the aligned spine causing injury. The aim of this study was to determine whether this effect exists under combined axial compression and lateral bending. Over two experimental studies, twenty-four human three vertebra functional spinal units were subjected to controlled dynamic axial compression at two levels of laterally eccentric force and in two end conditions. One end condition allowed the superior spine to laterally rotate and translate (T-Free) and the other end condition allowed only lateral rotation (T-Fixed). Spine kinetics, kinematics, injuries and occlusion of the spinal canal were measured during impact and pre- and post-impact flexibility. In contrast to typical spine responses in flexion-compression loading, the cervical spine specimens in this study did not escape injury in lateral bending when allowed to translate laterally. The specimen group that allowed lateral translation during compression had more injuries at high laterally eccentric force, saw greater peak canal occlusions and post-impact flexibility than constrained specimens.

Cervical spine injuries often happen in dynamic environments (e.g., sports and motor vehicle crashes) where individuals may be moving their head and neck immediately prior to impact. This motion may reposition the cervical vertebrae in a way that is dissimilar to the upright resting posture that is often used as the initial position in cadaveric studies of catastrophic neck injury. Therefore our aim was to compare the "neutral" cervical alignment measured using fluoroscopy of 11 human subjects while resting in a neutral posture and as their neck passed through neutral during the four combinations of active flexion and extension movements in both an upright and inverted posture. Muscle activation patterns were also measured unilaterally using surface and indwelling electromyography in 8 muscles and then compared between the different conditions. Overall, the head posture, cervical spine alignment and muscle activation levels were significantly different while moving compared to resting upright. Compared to the resting upright condition, average head postures were 6-13° more extended, average vertebral angles varied from 11° more extended to 10° more flexed, and average muscle activation levels varied from unchanged to 10% MVC more active, although the exact differences varied with both direction of motion and orientation. These findings are important for ex vivo testing where the head and neck are statically positioned prior to impact - often in an upright neutral posture with negligible muscle forces - and suggest that current cadaveric head-first impact tests may not reflect many dynamic injury environments.

MINI: Identifying fracture is important for understanding vertebral mechanics. Isolated cadaveric thoracolumbar vertebrae were compressed, and surface strains were measured using digital image correlation. Fracture locations from video analysis were qualitatively similar to the locations of high compressive strains and local damage occurred before the maximum force was reached. STUDY DESIGN Ex vivo compression experiments on isolated cadaveric vertebrae. OBJECTIVE To qualitatively compare the fracture locations identified in video analysis with the locations of high compressive strain measured with digital image correlation (DIC) on vertebral bodies and to evaluate the timing of local damage to the cortical shell relative to the global yield force. SUMMARY OF BACKGROUND DATA In previous ex vivo experiments, cortical bone fracture has been identified using various methods including acoustic emission sensors, strain gages, video analysis, or force signals. These methods are, however, limited in their ability to detect the location and timing of fracture. We propose use of DIC, a noncontact optical technique that measures surface displacement, to quantify variables related to damage. METHODS Isolated thoracolumbar human cadaveric vertebral bodies (n = 6) were tested in compression to failure at a quasi-static rate, and the force applied was measured using a load cell. The surface displacement and strain were measured using DIC. Video analysis was performed to identify fractures. RESULTS The location of fractures identified in the video corresponded well with the locations of high compressive strain on the bone. Before reaching the global yield force, more than 10% of the DIC measurements reached a minimum principal strain of 1.0%, a previously reported threshold for cortical bone damage. CONCLUSION DIC measurements provide an objective measure that can be used to identify the location and timing of fractures during ex vivo vertebral experiments. This is important for understanding fracture mechanics and for validating vertebral computational models that incorporate failure. LEVEL OF EVIDENCE N /A.

Computational models of the human brain are widely used in the evaluation and development of helmets and other protective equipment. These models are often attempted to be validated using cadaver tissue displacements despite studies showing neural tissue degrades quickly after death. Addressing this limitation, this study aimed to develop a technique for quantifying living brain motion in vivo using a closed head impact animal model of traumatic brain injury (TBI) called CHIMERA. We implanted radiopaque markers within the brain of three adult ferrets and resealed the skull while the animals were anesthetized. We affixed additional markers to the skull to track skull kinematics. The CHIMERA device delivered controlled, repeatable head impacts to the head of the animals while the impacts were fluoroscopically stereo-visualized. We observed that 1.5 mm stainless steel fiducials (∼8 times the density of the brain) migrated from their implanted positions while neutral density targets remained in their implanted position post-impact. Brain motion relative to the skull was quantified in neutral density target tests and showed increasing relative motion at higher head impact severities. We observed the motion of the brain lagged behind that of the skull, similar to previous studies. This technique can be used to obtain a comprehensive dataset of in vivo brain motion to validate computational models reflecting the mechanical properties of the living brain. The technique would also allow the mechanical response of in vivo brain tissue to be compared to cadaveric preparations for investigating the fidelity of current human computational brain models.

The majority of hip fractures in the elderly are the result of a fall from standing or from a lower height. Current injury models focus mostly on femur strength while neglecting subject-specific loading. This article presents an injury modeling strategy for hip fractures related to sideways falls that takes subject-specific impact loading into account. Finite element models (FEMs) of the human body were used to predict the experienced load and the femoral strength in a single model. We validated these models for their predicted peak force, effective pelvic stiffness, and fracture status against matching ex vivo sideways fall impacts (n = 11) with a trochanter velocity of 3.1 m/s. Furthermore, they were compared to sideways impacts of volunteers with lower impact velocities that were previously conducted by other groups. Good agreement was found between the ex vivo experiments and the FEMs with respect to peak force (root mean square error [RMSE] = 10.7%, R2 = 0.85) and effective pelvic stiffness (R2 = 0.92, RMSE = 12.9%). The FEMs were predictive of the fracture status for 10 out of 11 specimens. Compared to the volunteer experiments from low height, the FEMs overestimated the peak force by 25% for low BMI subjects and 8% for high BMI subjects. The effective pelvic stiffness values that were derived from the FEMs were comparable to those derived from impacts with volunteers. The force attenuation from the impact surface to the femur ranged between 27% and 54% and was highly dependent on soft tissue thickness (R2 = 0.86). The energy balance in the FEMS showed that at the time of peak force 79% to 93% of the total energy is either kinetic or was transformed to soft tissue deformation. The presented FEMs allow for direct discrimination between fracture and nonfracture outcome for sideways falls and bridge the gap between impact testing with volunteers and impact conditions representative of real life falls. © 2019 American Society for Bone and Mineral Research.

Many pathologies involving disc degeneration are treated with surgery and spinal implants. It is important to understand how the spine behaves mechanically as a function of disc degeneration. Shear loading is especially relevant in the natural and surgically stabilized lumbar spine. The objective of our study was to determine the effect of disc degeneration on anterior translation of the lumbar spine under shear loading. We tested 30 human cadaveric functional spinal units (L3–4 and L4–5) in anterior shear loading. First, the specimens were imaged in a 1.5 T magnetic resonance scanner. The discs were graded according to the Pfirrmann classification. The specimens were then loaded up to 250 N in anterior shear with an axial compression force of 300 N. Motion of the vertebrae was captured with an optoelectronic camera system. Inter- and intra-observer reliability for disc grading was determined (Cohen's and Fleiss' Kappa), and a non-parametric test was performed on the translation data to characterize the effect of disc degeneration on this parameter. We found fair to moderate agreement between and within observers for the disc grading. We found no significant effect of disc degeneration on anterior shear translation (Kruskal-Wallis ANOVA). Our results indicate that disc degeneration, as classified with the Pfirrmann scale, does not predict lumbar spinal motion in shear. © 2015 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 33:450–457, 2015.

Current screening techniques based on areal bone mineral density (aBMD) measurements are unable to identify the majority of people who sustain hip fractures. Biomechanical examination of such events may help determine what predisposes a hip to be susceptible to fracture. Recently, drop-tower simulations of in-vitro sideways falls have allowed the study of the mechanical response of the proximal human femur at realistic impact speeds. This technique has created an opportunity to validate explicit finite element (FE) models against dynamic test data. This study compared the outcomes of 15 human femoral specimens fractured using a drop tower with complementary specimen-specific explicit FE analysis. Correlation coefficient and root mean square error (RMSE) were found to be moderate for whole bone stiffness comparison (R2=0.3476 and 22.85% respectively). No correlation was found between experimentally and computationally predicted peak force, however, energy absorption comparison produced moderate correlation and RMSE (R2=0.4781 and 29.14% respectively). By comparing predicted strain maps to high speed video data we demonstrated the ability of the FE models to detect vulnerable portions of the bones. Based on our observations, we conclude that there exists a need to extend the current apparent level material models for bone to cover higher strain rates than previously tested experimentally.

Understanding proximal femur fracture may yield new targets for fracture prevention screening and treatment. The goal of this study was to characterize force-displacement and failure behaviours in the proximal femur between displacement control and impact loading fall simulations. Twenty-one human proximal femurs were tested in two ways, first to a sub-failure load at a constant displacement rate, then to fracture in an impact fall simulator. Comparisons of sub-failure energy and stiffness were made between the tests at the same compressive force. Additionally, the impact failure tests were compared with previous, constant displacement rate failure tests (at 2 and 100mm/s) in terms of energy, yield force, and stiffness. Loading and displacement rates were characterized and related to specimen stiffness in the impact tests. No differences were observed between the sub-failure constant displacement and impact tests in the aforementioned metrics. Comparisons between failure tests showed that the impact group had the lowest absorbed energy, 24% lower maximum force and 160% higher stiffness than the 100mm/s group (p

Little is known about the internal mechanics of the in vivo spinal cord during injury. The objective of this study was to develop a method of tracking internal and surface deformation of in vivo rat spinal cord during compression using radiography. Since neural tissue is radio-translucent, radio-opaque markers were injected into the spinal cord. Two tantalum beads (260 µm) were injected into the cord (dorsal and ventral) at C5 of nine anesthetized rats. Four beads were glued to the lateral surface of the cord, caudal and cranial to the injection site. A compression plate was displaced 0.5 mm, 2 mm, and 3 mm into the spinal cord and lateral X-ray images were taken before, during, and after each compression for measuring bead displacements. Potential bead migration was monitored for by comparing displacements of the internal and glued surface beads. Dorsal beads moved significantly more than ventral beads with a range in averages of 0.57-0.71 mm and 0.31-0.35 mm respectively. Bead displacements during 0.5 mm compressions were significantly lower than 2 mm and 3 mm compressions. There was no statistically significant migration of the internal beads. The results indicate the merit of this technique for measuring in vivo spinal cord deformation. The pattern of bead displacements illustrates the complex internal and surface deformations of the spinal cord during transverse compression. This information is needed for validating physical and finite element spinal cord surrogates and to define relationships between loading parameters, internal cord deformation, and biological and functional outcomes.

Current neck injury criteria do not include limits for lateral bending combined with axial compression and this has been observed as a clinically relevant mechanism, particularly for rollover motor vehicle crashes. The primary objectives of this study were to evaluate the effects of lateral eccentricity (the perpendicular distance from the axial force to the centre of the spine) on peak loads, kinematics, and spinal canal occlusions of subaxial cervical spine specimens tested in dynamic axial compression (0.5 m/s). Twelve 3-vertebra human cadaver cervical spine specimens were tested in two groups: low and high eccentricity with initial eccentricities of 1 and 150% of the lateral diameter of the vertebral body. Six-axis loads inferior to the specimen, kinematics of the superior-most vertebra, and spinal canal occlusions were measured. High speed video was collected and acoustic emission (AE) sensors were used to define the time of injury. The effects of eccentricity on peak loads, kinematics, and canal occlusions were evaluated using unpaired Student t-tests. The high eccentricity group had lower peak axial forces (1544 ± 629 vs. 4296 ± 1693 N), inferior displacements (0.2 ± 1.0 vs. 6.6 ± 2.0 mm), and canal occlusions (27 ± 5 vs. 53 ± 15%) and higher peak ipsilateral bending moments (53 ± 17 vs. 3 ± 18 Nm), ipsilateral bending rotations (22 ± 3 vs. 1 ± 2°), and ipsilateral displacements (4.5 ± 1.4 vs. -1.0 ± 1.3 mm, p0.05 for all comparisons). These results provide new insights to develop prevention, recognition, and treatment strategies for compressive cervical spine injuries with lateral eccentricities.

Finite element (FE) analysis based on quantitative computed tomography (QCT) images is an emerging tool to estimate bone strength in a specific patient or specimen; however, it is limited by the computational power required and the associated time required to generate and solve the models. Thus, our objective was to develop a fast, validated method to estimate whole bone structural stiffness and failure load in addition to a sensitivity analysis of varying boundary conditions. We performed QCT scans on twenty fresh-frozen proximal femurs (age: 77±13 years) and mechanically tested the femurs in a configuration that simulated a sideways fall on the hip. We used custom software to generate the FE models with boundary conditions corresponding to the mechanical tests and solved the linear models to estimate bone structural stiffness and estimated failure load. For the sensitivity analysis, we varied the internal rotation angle of the femoral neck from -30° to 45° at 15° intervals and estimated structural stiffness at each angle. We found both the FE estimates of structural stiffness (R(2)=0.89, p

Ice hockey body checks involving direct shoulder-to-head contact frequently result in head injury. In the current study, we examined the effect of shoulder pad style on the likelihood of head injury from a shoulder-to-head check. Shoulder-to-head body checks were simulated by swinging a modified Hybrid-III anthropomorphic test device (ATD) with and without shoulder pads into a stationary Hybrid-III ATD at 21 km/h. Tests were conducted with three different styles of shoulder pads (traditional, integrated and tethered) and without shoulder pads for the purpose of control. Head response kinematics for the stationary ATD were measured. Compared to the case of no shoulder pads, the three different pad styles significantly (p

Study Design. A biomechanical human cadaveric study. Objective. To determine the percentage of shear force supported by posterior lumbar spinal devices of varying stiffnesses under anterior shear loading in a degenerative spondylolisthesis model. Summary of Background Data. Clinical studies have demonstrated beneficial results of posterior arthrodesis for the treatment of degenerative spinal conditions with instability. Novel spinal implants are designed to correct and maintain spinal alignment, share load with the spine, and minimize adjacent level stresses. The optimal stiffness of these spinal systems is unknown. To our knowledge, low-stiffness posterior instrumentation has not been tested under an anterior shear force, a highly relevant force to be neutralized in the clinical case of degenerative spondylolisthesis. Methods. The effects of implant stiffness and specimen condition on implant load and intervertebral motion were assessed in a biomechanical study. Fifteen human cadaveric lumbar functional spinal units were tested under a static 300 N axial compression force and a cyclic anterior shear force (5–250 N). Implants (high-stiffness [HSI]: o 5.5-mm titanium, medium-stiffness [MSI]: o 6.35 × 7.2-mm oblong PEEK, and low-stiffness [LSI]: o 5.5-mm round PEEK) instrumented with strain gauges were used to calculate loads and were tested in each of 3 specimen conditions simulating degenerative changes: intact, facet instability, and disc instability. Intervertebral motions were measured with a motion capture system. Results. As predicted, implants supported a significantly greater shear force as the specimen was progressively destabilized. Mean implant loads as a percent of the applied shear force in order of increasing specimen destabilization for the HSI were 43%, 67%, and 76%; mean implant loads for the MSI were 32%, 56%, and 77%; and mean implant loads for the LSI were 18%, 35%, and 50%. Anterior translations increased with decreasing implant stiffness and increasing specimen destabilization. Conclusion. Implant shear stiffness significantly affected the load sharing between the implant and the natural spine in anterior shear ex vivo. Low-stiffness implants transferred significantly greater loads to the spine. This study supports the importance of load-sharing behavior when designing new implants.

STUDY DESIGN: Quantitative in vivo ultrasound imaging study of spinal cord and dura morphology after acute experimental spinal cord injury (SCI) and decompression in a pig model. OBJECTIVE: To study the morphological changes of the spinal cord and dura immediately after surgical decompression for acute SCI. SUMMARY OF BACKGROUND DATA: Surgical decompression for traumatic SCI is currently a topic of debate. After decompression, relief of bony impingement on the thecal sac and spinal cord can be confirmed intraoperatively. However, postoperative imaging often reveals that the cord has swollen to fill the subarachnoid space. Little is known about the extent and timing of this morphological response. METHODS: Yucatan miniature pigs received sham surgery (N = 1) or a moderate (N = 6, 20 g, 2.3 m/s) or high (N = 6, 20 g, 4.7 m/s) severity weight-drop SCI followed by 8 hours of sustained compression (100 g) and 6 hours of postdecompression monitoring. Sagittal-plane ultrasound images were used to quantify spinal cord, dura, and subarachnoid space dimensions preinjury and once per hour after decompression. RESULTS: Animals with a moderate SCI exhibited a residual cord deformation of up to 0.64 mm within 10 minutes of decompression, which tended to resolve during 6 hours because of tissue relaxation and swelling. For animals with high-severity SCIs, cord swelling was immediate and resulted in occlusion of the subarachnoid space within 10 minutes to 5 hours, whereas this occurred for only half of the moderate injury group. CONCLUSION: Decompression of an acute SCI may result in residual cord deformation followed by gradual swelling or immediate swelling leading to subarachnoid occlusion. The response is dependent on initial injury severity. These observations may partly explain the lack of benefit of decompression in some patients and suggest a need to reduce cord swelling to optimize the clinical outcome after acute SCI.

Acoustic emission (AE) sensors are a reliable tool in detecting fracture, however they have not been used to differentiate between compressive osseous and tensile ligamentous failures in the spine. This study evaluated the effectiveness of AE data in detecting the time of injury of ligamentum flavum (LF) and vertebral body (VB) specimens tested in tension and compression, respectively, and in differentiating between these failures. AE signals were collected while LF (n=7) and VB (n=7) specimens from human cadavers were tested in tension and compression (0.4 m/s), respectively. Times of injury (time of peak AE amplitude) were compared to those using traditional methods (VB: time of peak force, LF: visual evidence in high speed video). Peak AE signal amplitudes and frequencies (using Fourier and wavelet transformations) for the LF and VB specimens were compared. In each group, six specimens failed (VB, fracture; LF, periosteal stripping or attenuation) and one did not. Time of injury using AE signals for VB and LF specimens produced average absolute differences to traditional methods of 0.7 (SD 0.2) ms and 2.4 (SD 1.5) ms (representing 14% and 20% of the average loading time), respectively. AE signals from VB fractures had higher amplitudes and frequencies than those from LF failures (average peak amplitude 87.7 (SD 6.9) dB vs. 71.8 (SD 9.8) dB for the inferior sensor, p

Cervical spine injuries in rugby union have received growing worldwide attention owing to their often catastrophic nature.1,–,3 Kuster et al 4 considered recent changes in the epidemiology as well as the ex vivo biomechanics literature on cervical spine injury during head-first impacts. Kuster postulated that the majority of catastrophic cervical spine injuries before year 2000 occurred through a hyperflexion mechanism in the scrum and since the year 2000, these injuries have occurred during tackles via an axial compression mechanism and related ‘buckling’ of the cervical spine. Regulators and other stakeholders in the game continually seek to improve understanding of the scope, true incidence and mechanism of these catastrophic injuries. Ideally, a full comprehension of cervical injury mechanisms occurring during rugby would lead to changes in the game, through rule changes or changes in enforcement and/or player coaching or education, which in turn would reduce the incidence of these injuries.2 Achieving such a full comprehension, however, has been elusive.1,–,3 ,5,–,9 For example, recent changes to the rules have led to reduced time spent in scrum and have altered scrum engagement, which subsequently have been associated with a reduction in incidence of scrum-related cervical spine injury (an injury primarily involving forward positions and accounting for 37%–51% of cervical spine injuries).5 ,7 ,8 ,10 ,11 These changes have therefore affected the distribution of players who get injured, with increased percentage of these injuries now being sustained by back positions than prior to these rule changes, and up to 57% of cervical injuries are now occurring …

Vertebral compression fracture repair aims to relieve pain and improve function by restoring vertebral structure and biomechanics, but is still associated with risks arising from polymethylmethacrylate cement extravasation. The Kiva® Vertebral Compression Fracture Treatment System, a stacked coil implant made of polyetheretherketone and delivered over a guide-wire, is a novel device designed to provide height restoration and mechanical stabilization, while improving cement containment and minimizing disruption of cancellous bone. The objective of this study was to determine whether the Kiva system is as effective as balloon kyphoplasty at restoring mechanical properties in osteoporotic vertebral compression fractures.Wedge fractures were created in the middle vertebra of fourteen osteoporotic three-vertebra spine segments and then repaired with either the Kiva or kyphoplasty procedure. Height, stiffness and displacement under compression of the spine segments were measured for four conditions: intact, fractured, augmented, and post-cyclic eccentric loading (50,000cycles, 200-500N, 30mm anterior lever arm).No significant differences were seen between the two procedures for height restoration, stiffness at high or low loads, or displacement under compression. However, the Kiva System required an average of 66% less cement than kyphoplasty to achieve these outcomes (mean 2.6 (SD 0.4) mL v. mean 7.5 (SD 0.8) mL 0; P0.01). Extravasations and excessive posterior cement flow were also significantly lower with Kiva (0/7 v. 4/7; P.05).Kiva exhibits similar biomechanical performance to balloon kyphoplasty, but may reduce the risk of extravasation through the containment mechanism of the implant design and by reducing cement volume.

Adjacent level degeneration that occurs above and/or below long fusion constructs is a documented clinical problem that is widely believed to be associated with the considerable change in stiffness caused by the fusion. Some researchers have suggested that early degeneration at spinal joints adjacent to a fusion could be treated by implanting total disc replacements at these levels. It is thought that further degeneration could be prevented through the disc replacement's design aims to reproduce normal disc heights, kinematics and tissue loading. For this reason, there is a clinical need to evaluate if a total disc replacement can maintain both the quantity of motion (i.e. range) and the quality of motion (i.e. center of rotation and coupling) at segments adjacent to a long spinal fusion. The purpose of this study was to experimentally evaluate range of motion (ROM-the intervertebral motion measured) and helical axis of motion (HAM) changes due to one- and two-level Maverick total disc replacement (TDR) adjacent to a long spinal fusion.Seven spine specimens (T8-S1) were used in this study (66 ± 19 years old, 3F/4 M). A continuous pure moment of ±5.0 Nm was applied to the specimen in flexion-extension (FE), lateral bending (LB) and axial rotation (AR), with a compressive follower preload of 400 N. The 5.0 Nm data were analyzed to evaluate the operated segment biomechanics at the level of the disc replacements. The data were also analyzed at lower moments using a modified version of Panjabi's proposed "hybrid" method to evaluate adjacent segment kinematics (intervertebral motion at the segments adjacent to the fusion) under identical overall (T8-S1) specimen rotations. The motion of each vertebra was monitored with an optoelectronic camera system. The biomechanical test was completed for (1) the intact condition and repeated after each surgical technique was applied to the specimen, (2) capsulotomy at L4-L5 and L5-S1, (3) T8-L4 fusion and capsulotomy at L4-L5 and L5-S1, (4) Maverick at L4-L5, and (5) Maverick at L5-S1. The capsulotomy was performed to allow measurement of facet joint loads in a companion study. Paired t tests were used to determine if differences in the kinematic parameters measured were significant. Holm-Sidak corrections for multiple comparisons were applied where appropriate.Under the 5.0 Nm loads, L4-L5 ROMs tended to decrease in all directions following L4-L5 Maverick replacement (mean = 22 %, compared to the fused condition). Two-level Maverick implantation also tended to reduce L4-S1 ROM (mean 18, 7 and 31 % in FE, LB and AR, respectively, compared to the fused condition without TDR). Following TDR replacement, the HAM location tended to shift posteriorly in FE (at L5-S1), anteriorly in AR, and inferiorly in LB. However, although the above-mentioned trends were observed, neither one- nor two-level TDR replacement showed statistically significant ROM or HAM change in any of the three directions. At the identical T8-S1 posture identified by the modified hybrid analysis, the L4-L5 and L5-S1 levels underwent significant larger motions, relative to the overall specimen rotation, after fusion. In the hybrid analysis, there were no significant differences between the ROM after fusion with intact natural discs at L4-L5 and L5-S1 and the motions at those levels with one or two TDRs implanted.The present results demonstrated that one or two Maverick discs implanted subjacent to a long thoracolumbar fusion preserved considerable and intact-like ranges of motion and maintained motion patterns similar to the intact specimen, in this ex vivo study with applied pure moments and compressive follower preload. The hybrid analysis demonstrated that, after fusion, the TDR-implanted levels are required to undergo large rotations, relative to those necessary before fusion, in order to achieve the same motion between T8 and S1. Additional clinical and biomechanical research is necessary to determine if such a kinematic demand would be made on these levels clinically and the biomechanical performance of these implants if it were.

Vertebral body fractures are the most common type of osteoporotic fractures.1,2 These fractures represent a growing public health concern because the incidence is projected to increase as the population ages.3 Vertebral fractures are associated with substantial increases in back pain, functional limitation, disability, and mortality.4,5 Falls are a major contributing factor to the occurrence of osteoporotic fractures6; 41% of vertebral fractures in older men are associated with falls from standing height or lower.7 The most common vertebral fracture site for older men is the lumbosacral spine, which represents 56% of all cases.7 Falls from standing height or lower also account for between 8% and 26% of spinal cord injuries,7,8 and more than two-thirds of these injuries occur in older adults.8 The risk of vertebral fracture in a backward fall depends, by definition, on a “factor of safety.” This factor of safety is defined as the ratio of the force that will typically result in failure under a loading configuration similar to that applied in the fall (i.e., tolerance) divided by the peak-applied force. Previous studies have measured the force applied to the buttocks in subinjurious backward falls in human subjects.9 The compressive force required to cause fracture of lumbar vertebrae has been determined by testing isolated cadaver spine segments.10–17 However, the peak forces occurring at the lumbosacral spine during a backward fall are not known, and this is a barrier to the development of injury prevention strategies. An intervention that has been suggested to reduce the incidence of fall-related fractures is the use of compliant or low-stiffness flooring.9,18,19 In a previous experimental study conducted by a subset of this study’s authors, human subjects fell from standing onto floors of various stiffnesses.9 Impact forces at the buttocks decreased with decreases in floor stiffness; however, the effect on spine forces was not addressed. To determine the effect of floor stiffness on spine forces experimentally, direct measurement of spinal component loads would be necessary; however, these are difficult to measure even during benign activities in vivo.10,11 Numerical models have been used to study the loads generated in the human spine during various activities,12–15 and this method has also been used to study spinal forces during trauma.16–18 Some of the previous models have been complex, have simulated multiple degrees of freedom at each joint, and have incorporated anatomic details such as the rib cage, lumbar muscles, viscera, facet joints, and intervertebral discs.12,14–16 Axial spine forces are related to fracture risk19–23; therefore, they are of primary interest in this study. It was our objective to develop an appropriate model to allow examination of the effect of floor stiffness on axial loading at various levels of the spine during a fall. We had access to a unique set of data to incorporate into our model. These human subject-specific data from our previous experimental study provided a level of verification for the present computational model.9 No previous mathematical modelling or experimental studies have examined spine forces resulting from a backward fall onto the buttocks. Accordingly, the specific objectives in this study were (1) to develop and verify a lumped-parameter model to predict intervertebral forces at several levels of the lumbosacral spine during backward falls from standing, (2) to evaluate the effect of floor stiffness on these forces, and (3) to examine how these compare with the axial force associated with fracture of the spine.

To gain insight into a new technology, a novel facet arthroplasty device (TFAS) was compared to a rigid posterior fixation system (UCR). The axial and bending loads through the implants and at the bone-implant interfaces were evaluated using an ex vivo biomechanical study and matched finite element analysis. Kinematic behaviour has been reported for TFAS, but implant loads have not. Implant loads are important indicators of an implant's performance and safety. The rigid posterior fixation system is used for comparison due to the extensive information available about these systems.Unconstrained pure moments were applied to 13 L3-S1 cadaveric spine segments. Specimens were tested intact, following decompression, UCR fixation and TFAS implantation at L4-L5. UCR fixation was via standard pedicle screws and TFAS implantation was via PMMA-cemented transpedicular stems. Three-dimensional 10 Nm moments and a 600 N follower load were applied; L4-L5 disc pressures and implant loads were measured using a pressure sensor and strain gauges, respectively. A finite element model was used to calculate TFAS bone-implant interface loads.UCR experienced greater implant loads in extension (p0.004) and lateral bending (p0.02). Under flexion, TFAS was subject to greater implant moments (p0.04). At the bone-implant interface, flexion resulted in the smallest TFAS (average = 0.20 Nm) but greatest UCR (1.18 Nm) moment and axial rotation resulted in the greatest TFAS (3.10 Nm) and smallest UCR (0.40 Nm) moments. Disc pressures were similar to intact for TFAS but not for UCR (p0.04).These results are most applicable to the immediate post-operative period prior to remodelling of the bone-implant interface since the UCR and TFAS implants are intended for different service lives (UCR--until fusion, TFAS--indefinitely). TFAS reproduced intact-like anterior column load-sharing--as measured by disc pressure. The highest bone-implant moment of 3.1 Nm was measured in TFAS and for the same loading condition the UCR interface moment was considerably lower (0.4 Nm). For other loading conditions, the differences between TFAS and UCR were smaller, with the UCR sometimes having larger values and for others the TFAS was larger. The long-term physiological meaning of these findings is unknown and demonstrates the need for a better understanding of the relationship between spinal arthroplasty devices and the host tissue as development of next generation motion-preserving posterior devices that hope to more accurately replicate the natural functions of the native tissue continues.

The Whistler Sliding Centre (WSC) in British Columbia, Canada, has played host to many events including the 2010 Winter Olympics. This study was performed to better understand sliding sport incident (crash, coming off sled, etc) and injury prevalence and provide novel insights into the effect of slider experience and track-specific influences on injury risk and severity.Track documentation and medical records over 4 years (2007 track inception to 2011) were used to form 3 databases, including over 43,200 runs (all sliding disciplines). Statistics were generated relating incident and injury to start location, crash location and slider experience as well as to understand injury characteristics.Overall injury rate was found to be 0.5%, with more severe injury occurring in0.1% of the total number of runs. More frequent and severe injuries were observed at lower track locations. Of 2605 different sliders, 73.6% performed 1-29 runs down the track. Increased slider experience was generally found to reduce the frequency of injury. Lacerations, abrasions and contusions represented 52% of all injuries. A fatality represented the most severe injury on the track and was the result of track ejection.By investigating the influence of start location, incident location and slider experience on incident and injury frequency and severity, a better understanding has been achieved of the inherent risks involved in sliding sports. Incident monitoring, with particular focus on track ejection, should be an emphasis of sliding tracks.

The relationship between bony spinal column and spinal cord injury during an injury event is not well understood. While several studies have measured spinal canal occlusion during axial impact, there has been limited work done to quantify the spinal cord compression or deformation during simulated injury. Because the cord is a viscoelastic solid it may provide resistance to bone fragments, ligaments or other elements that move into the canal and impinge it during column injury. This would differentiate the measurement of cord compression from the measurement of occlusion of an empty canal. In the present study, a novel method of visualizing and quantifying spinal cord deformation during dynamic head-first impact of ex vivo human cervical spine specimens (N=6) was developed. A radiodense, biofidelic surrogate spinal cord was imaged in the spinal canal using high speed cineradiography at 1000 frames per second. The dorsal-ventral diameter of the cord was measured at 1.5mm increments along its length for each frame of the radiographic footage. The resulting cord deformations were used to determine the theoretical neurological outcome of the impact based on published in vivo ferret studies. The corresponding probability of recovery for the spinal cord deformations in these tests ranged between 8% for atlantoaxial dislocation injury and 95% for mid-cervical spine hyperextension injury (based on the ferret data). Clinically relevant spinal column fracture patterns were produced in this study. Language: en

STUDY DESIGN: Cross-sectional study. OBJECTIVE: To determine the effect of age and sex on the three-dimensional kinematics of the cervical spine. SUMMARY OF BACKGROUND DATA: Spine kinematics information has important implications for biomechanical model development, anthropomorphic test device development, injury prevention, surgical treatment, and safety equipment design. There is a paucity of data of this type available for children, and it is unknown whether cervical spine kinematics of the pediatric population is different than that of adults. The helical axis of motion (HAM) of the spine provides unique information about the quantity and quality (coupling etc.) of the measured motion. METHODS: Ninety subjects were recruited and divided into 6 groups based on sex and age (young children aged 4-10 years, older children aged 11-17 years, adults aged 25+ years). Subjects actively moved their head in axial rotation, lateral bending, and flexion/extension. An optoelectronic motion analysis system recorded the position of infrared markers placed on the first thoracic vertebrae (T1) and on tight-fitting headgear worn by the subjects. HAM parameters were calculated for the head motion with respect to T1. RESULTS: HAM location in axial rotation and flexion/extension was more anterior in young females compared to adult females. Young females had a more anterior HAM location in flexion/extension compared to young males, indicating an effect of sex. For females, the HAM locations of adults were superior to those of children in flexion/extension and lateral bending whereas in males the HAM locations of adults were inferior to those of children. Age-related differences in HAM orientation were also observed in axial rotation and lateral bending. CONCLUSION.: Cervical spine kinematics vary with age and sex. The variation in spine mechanics based on age and sex found in the present study may indicate general trends that would grow stronger in even younger children (age Language: en

To prevent spinal cord injury, optimize treatments for it, and better understand spinal cord pathologies such as spondylotic myelopathy, the interaction between the spinal column and the spinal cord during injury and pathology must be understood. The spinal cord is a complex and very soft tissue that changes properties rapidly after death and is difficult to model. Our objective was to develop a physical surrogate spinal cord with material properties closely corresponding to the in vivo human spinal cord that would be suitable for studying spinal cord injury under a variety of injurious conditions. Appropriate target material properties were identified from published studies and several candidate surrogate materials were screened, under uniaxial tension, in a materials testing machine. QM Skin 30, a silicone elastomer, was identified as the most appropriate material. Spinal cords manufactured from QM Skin 30 were tested under uniaxial tension and transverse compression. Rectangular specimens of QM Skin 30 were also tested under uniform compression. QM Skin 30 produced surrogate cords with a Young's modulus in tension and compression approximately matching values reported for in vivo animal spinal cords (0.25 and 0.20 MPa, respectively). The tensile and compressive Young's modulus and the behavior of the surrogate cord simulated the nonlinear behavior of the in vivo spinal cord.

Study design An ex vivo biomechanical study using porcine spinal segments. Objective To produce a biomechanical model of both spondylolysis and spondylolisthesis using an accelerated cyclic loading model with intermittent impulse loads. Summary of background data Only a few models of spondylolisthesis appropriate for biomechanical testing have been presented previously. Past modeling attempts have largely required nonphysiologic gross fracture of the pars before testing and have resulted in nonphysiologic endplate fracture. In these tests no clinically relevant spondylolisthesis was seen at the end of testing. A reproducible, clinically relevant model of both spondylolysis and spondylolisthesis would allow study of these disease processes, and facilitate the development and evaluation of advanced spinal implants optimized specifically for these pathologies. Methods Five porcine lumbar functional spinal units were tested (2 L4-L5, 3 L6-S1) after small notches had been created in the pars and after the disc had specific collagen fibers in the anterior anulus sectioned. Specimens were loaded with a constant cranial-caudal compressive force of 300 N and the application of cyclic anterior shear loads between 300 and 600 N with intermittent impulse loads to 1500 N until pars fracture occurred. Elevated cyclic loading then continued between 500 and 800 N. Results All specimens displayed bilateral pars fracture with the fractures passing through the points of notching and no damage to endplates or facet joints. Clinically-relevant Grade II spondylolisthesis was achieved in all 5 specimens. The mean slip at the conclusion of testing was 33%. Conclusion Cyclic shear loading with intermittent impulse loads can reliably create fracture in the pars interarticularis in ex vivo porcine spine segments. Subsequent cyclic anterior motion of the superior vertebra results in clinically-relevant spondylolysis and spondylolisthesis.

Thoracolumbar burst fracture is one of the most common and most studied injuries of the spine. Radiography and quantitative discomanometry have previously demonstrated that intervertebral discs adjacent to a burst fracture were disrupted; however, there have been conflicting data on the properties of the next-adjacent discs. Also, no data exists on the localization of injury within each disc. The objective of this study is to use an in vitro biomechanical design to examine the flexibility differences of intervertebral discs adjacent and next-adjacent to burst fracture vertebrae. Ten cadaveric thoracolumbar (T11–L3) spines with L1 burst fracture included adjacent (T12–L1, L1–L2) and next-adjacent (T11–T12, L2–L3) intervertebral discs. The bending flexibilities (μm/N) of each disc under 50 N of compression were determined at 25 points: the center point, along with the combinations of three radii (1 cm, 2 cm, 3 cm) and eight angles. The overall flexibility of each disc and the presence of any regional differences were then evaluated. Across all radii, the T11μT12 disc was statistically less flexible than the other three discs (p < 0.01). The difference between the flexibilities of the average anterior region and the average posterior region was significant at many 2-cm and all 3-cm radii; this difference was greater in the T12–L1 disc than in any of the other three discs. Thus, the upper next-adjacent intervertebral disc (T11–T12) was not as susceptible to mechanical disruption as were the other three discs. The anterior region of each disc may also have a higher propensity for mechanical disruption than the posterior region, especially at larger radii.

STUDY DESIGN Nucleus pressure was measured within porcine intervertebral discs (IVDs) with a novel in-fiber Bragg grating (FBG) sensor (0.4 mm diameter) and a strain gauge (SG) sensor (2.45 mm). OBJECTIVE To validate the accuracy of a new FBG pressure sensor designed for minimally invasive measurements of nucleus pressure. SUMMARY OF BACKGROUND DATA Although its clinical utility is controversial, it is possible that the predictive accuracy of discography can be improved with IVD pressure measurements. These measurements are typically obtained using needle-mounted SG sensors inserted into the nucleus. However, by virtue of their size, SG sensors alter disc mechanics, injure anulus fibers, and can potentially initiate or accelerate degenerative changes thereby limiting their utility particularly clinically. METHODS Six functional spinal units were loaded in compression from 0 N to 500 N and back to 0 N; nucleus pressure was measured using the FBG and SG sensors at various locations along anterior and anterolateral axes. RESULTS On average maximum IVD pressures measured using the FBG and SG sensors were within 9.39% of each other. However, differences between maximum measured pressures from the FBG and SG sensors were larger (22.2%) when the SG sensor interfered with vertebral endplates (P < 0.05). The insertion of the FBG sensor did not result in visible damage to the anulus, whereas insertion of the SG sensor resulted in large perforations in the anulus through which nucleus material was visible. CONCLUSION The new FBG sensor is smaller and less invasive than any previously reported disc pressure sensor and gave results consistent with previous disc pressure studies and the SG sensor. There is significant potential to use this sensor during discography while avoiding the controversy associated with disc injury as a result of sensor insertion.

Background Proximal humerus fractures are a common fragility fracture that significantly affects the independence of older adults. The outcomes of these fractures are frequently disappointing and previous systematic reviews are unable to guide clinical practice. Through an integrated knowledge user collaboration, we sought to map the breadth of literature available to guide the management of proximal humerus fractures. Methods We utilized a scoping review technique because of its novel ability to map research activity and identify knowledge gaps in fields with diverse treatments. Through multiple electronic database searches, we identified a comprehensive body of proximal humerus fracture literature that was classified into eight research themes. Meta-data from each study were abstracted and descriptive statistics were used to summarize the results. Results 1,051 studies met our inclusion criteria with the majority of research being performed in Europe (64%). The included literature consists primarily of surgical treatment studies (67%) and biomechanical fracture models (10%). Nearly half of all clinical studies are uncontrolled case series of a single treatment (48%). Non-randomized comparative studies represented 12% of the literature and only 3% of the studies were randomized controlled trials. Finally, studies with a primary outcome examining the effectiveness of non-operative treatment or using a prognostic study design were also uncommon (4% and 6%, respectively). Conclusions The current study provides a comprehensive summary of the existing proximal humerus fracture literature using a thematic framework developed by a multi-disciplinary collaboration. Several knowledge gaps have been identified and have generated a roadmap for future research priorities. Electronic supplementary material The online version of this article (doi:10.1186/s12891-015-0564-8) contains supplementary material, which is available to authorized users.

Experimental data suggest that lumbar torsion contributes to lumbar disc degenerative changes, such as instability, spondylolisthesis and spinal canal stenosis. However, some basic mechanical characteristics of the lumbar spine under torsional loading have not yet been reported in detail. For example, the function of the facet joints under combined mechanical loads such as torsion with superimposed flexion or extension postures is an area of interest about which little biomechanical data have been reported. In this study, the kinematic response to axial torsion with superimposed axial compression (200 N), compression-flexion (3 and 6 Nm) and compression-extension (3 and 6 Nm) was investigated in 10 cadaveric lumbar functional spinal units. Range of motion (ROM), and helical axes of motion (HAM), were analyzed. There was no difference in ROM between no preload, pure compressive and flexion-compression preload conditions. The ROM was significantly reduced by both extension-compression preload conditions (11% reduction for 3 Nm and 19% reduction for 6 Nm of extension) compared to the pure compressive preload. For no preload, the average HAM position in the transverse plane of the intervertebral disc was near the posteriormost part of the disc and located laterally on the side contralateral to the applied torsional moment. In the transverse plane, the HAM position showed a discrete trend towards the posterior part of the specimens during extension. Kinematic data were visualized using computer animation techniques and CT-based reconstructions of the respective specimens. This information may be used for identifying and characterizing physiologic and pathologic motion and for specifying conservative and surgical treatment concepts and, thus, may find application to identifying indications for spinal fusion or in evaluating the effect of future semi-flexible instrumentation.

Study Design. An in vitro flexibility study of C2-T1 specimens under compressive preload. Objective. To determine three-dimensional flexibility test moments needed to obtain spinal kinematics representative of the in vivo spine studies. Summary of Background Data. Most previous three-dimensional in vitro cervical spine studies have used equal moments in all three planes to evaluate spinal flexibilities. Recent advances have made it possible to apply physiologic compressive preload. It is unclear what moments should be applied to these preloaded spine segments to simulate in vivo kinematics. Methods. Six fresh human cadaveric cervical spine specimens (C2-T1) were used. The preload (100 N) was applied by flexible cables, which passed through guides attached to each vertebra. Flexibility tests of flexion-extension and bilateral axial torsion and lateral bending were performed. Two protocols were compared, 1:1:1 with equal pure moments of 1 Nm for each direction and 2:4:2 with pure moments of 2 Nm for flexion-extension and lateral bending and 4 Nm for axial torsion. Ranges of motion were calculated from the flexibility tests. Results. The 2:4:2 protocol resulted in significantly better agreement with in vivo data than did the 1:1:1 protocol, in flexion-extension, the 2 Nm value was within 17% of the average in vivo value, in axial torsion, the 4 Nm value was within 22% of the in vivo average. In lateral bending, the 2 Nm value was within 15% of the in vivo average. Conclusions. To obtain human in vivo-like kinematics using 100 N preioad, the 2:4:2 protocol is to be recommended.

STUDY DESIGN In vivo human volunteer study of the intervertebral postural changes and muscle activity levels while tensing the neck muscles. OBJECTIVE To determine if actively tensing the neck muscles changes the posture of the cervical spine and, because axial impact neck injury often occurs while inverted, whether these changes exist both upright and upside down. SUMMARY OF BACKGROUND DATA Rollover accidents are dynamic and complex events in which head contacts with the vehicle interior can cause catastrophic neck injuries. Computational modeling has suggested that active neck muscles may increase the risk of cervical spine fracture in a rollover crash. Cadaver testing has also demonstrated that overall neck alignment and curvature are key to understanding and preventing catastrophic neck injuries. Although muscle activity and neck posture affects the resulting injury, there are currently no in vivo data describing how tensing the neck muscles influences intervertebral posture. METHODS Eleven human subjects (6 females, 5 males) actively tensed their neck muscles while seated upright and inverted. Vertebral alignment was measured using fluoroscopy and muscle activity was recorded using surface and indwelling electrodes in 8 neck muscles. RESULTS On average, tensed muscles increased cervical spine curvature and anterior motion of the cervical vertebrae relative to the torso. These changes, which were magnified by inversion, indicate that cervical intervertebral posture differs considerably between the relaxed and tensed states. CONCLUSION Active muscle contraction can change the vertebral alignment in upright and inverted postures. This change in posture may alter the load path and injury mechanics during an axial head impact and may help explain the disparity between the neck injuries observed in real-world rollover accidents and ex vivo cadaver experiments. LEVEL OF EVIDENCE N/A.

Dynamic implants have been developed to address potential adjacent level effects due to rigid instrumentation. Rates of revision surgeries may be reduced by using improved implants in the primary surgery. Prior to clinical use, implants should be rigorously tested ex vivo. The objective of our study was to characterize the load-sharing and kinematic behavior of a novel low-stiffness spinal implant.A human cadaveric model of degenerative spondylolisthesis was tested in shear. Lumbar functional spinal units (N = 15) were tested under a static 300 N axial compression force and a cyclic anterior shear force (5-250 N). Translation was tracked with a motion capture system. A novel implant was compared to three standard implants with shear stiffness ranging from low to high. All implants were instrumented with strain gauges to measure the supported shear force. Each implant was affixed to each specimen, and the specimens were tested intact and in two progressively destabilized states.Specimen condition and implant type affected implant load-sharing and specimen translation (p0.0001). Implant load-sharing increased across all degeneration-simulating specimen conditions and decreased across the three standard implants (high- to low-stiffness). Translation increased with the three standard implants (trend). The novel implant behaved similarly to the medium-stiffness implant (p0.2).The novel implant behaved similarly to the medium-stiffness implant in both load-sharing and translation despite having a different design and stiffness. Complex implant design and specimen-implant interaction necessitate pre-clinical testing of novel implants. Further in vitro testing in axial rotation and flexion-extension is recommended as they are highly relevant loading directions for non-rigid implants.

A novel technique to measure in vitro disc pressures in human cervical spine specimens was developed. A miniature pressure transducer was used and an insertion technique was designed to minimise artefacts due to insertion. The technique was used to measure the intradiscal pressure in cervical spines loaded in pure axial compression. The resulting pressure varied linearly with the applied compressive force with coefficients of determination ( r 2 ) greater than 0.99 for each of the four specimens. Peak pressures between 2.4 and 3.5 MPa were recorded under 800 N of compression.

Determine the effects of dynamic injurious axial compression applied at various lateral eccentricities (lateral distance to the centre of the spine) on mechanical flexibilities and structural injury patterns of the cervical spine. 13 three-vertebra human cadaver cervical spine specimens (6 C3–5, 3 C4–6, 2 C5–7, 2 C6–T1) were subjected to pure moment flexibility tests (±1.5 Nm) before and after impact trauma was applied in two groups: low and high lateral eccentricity (1 and 150 % of the lateral diameter of the vertebral body, respectively). Relative range of motion (ROM) and relative neutral zone (NZ) were calculated as the ratio of post and pre-trauma values. Injuries were diagnosed by a spine surgeon and scored. Classification functions were developed using discriminant analysis. Low and high eccentric loading resulted in primarily bony fractures and soft tissue injuries, respectively. Axial impacts with high lateral eccentricities resulted in greater spinal motion in lateral bending [median relative ROM 3.5 (interquartile range, IQR 2.3) vs. 1.4 (IQR 0.5) and median relative NZ 4.7 (IQR 3.7) vs. 2.3 (IQR 1.1)] and in axial rotation [median relative ROM 5.3 (IQR 13.7) vs. 1.3 (IQR 0.5), p

Presently, there is little consensus about how, or even if, axial preload should be incorporated in spine flexibility tests in order to simulate the compressive loads naturally present in vivo. Some preload application methods are suspected of producing unwanted “artefact” forces as the specimen rotates and, in doing so, influencing the resulting kinematics. The objective of this study was to quantitatively compare four distinct types of preload which have roots in contemporary experimental practice. The specific quantities compared were the reaction moments and forces resulting at the intervertebral disc and specimen kinematics. The preload types incorporated increasing amounts of caudal constraint on the preload application vector ranging from an unconstrained dead-load arrangement to an apparatus that allowed the vector to follow rotations of the specimen. Six human cadaveric spine segments were tested (1-L1/L2, 3-L2/L3, 1-L3/L4 and 1-L4/L5). Pure moments were applied to the specimens with each of the four different types of compressive preload. Kinematic response was measured using an opto-electronic motion analysis system. A six-axis load cell was used to measure reaction forces and moments. Artefact reaction moments and shear forces were significantly affected by preload application method and magnitude. Unconstrained preload methods produced high artefact moments and low artefact shear forces while more constrained methods did the opposite. A mechanical trade-off is suggested by our results, whereby unwanted moment can only be prevented at the cost of shear force production. When comparing spine flexibility studies, caution should be exercised to ensure preload was applied in a similar manner for all studies. Unwanted moments or forces induced as a result of preload application method may render the comparison of two seemingly similar studies inappropriate.

We performed a biomechanical study on human cadaver spines to determine the effect of three different interbody cage designs, with and without posterior instrumentation, on the three-dimensional flexibility of the spine. Six lumbar functional spinal units for each cage type were subjected to multidirectional flexibility testing in four different configurations: intact, with interbody cages from a posterior approach, with additional posterior instrumentation, and with cross-bracing. The tests involved the application of flexion and extension, bilateral axial rotation and bilateral lateral bending pure moments. The relative movements between the vertebrae were recorded by an optoelectronic camera system. We found no significant difference in the stabilising potential of the three cage designs. The cages used alone significantly decreased the intervertebral movement in flexion and lateral bending, but no stabilisation was achieved in either extension or axial rotation. For all types of cage, the greatest stabilisation in flexion and extension and lateral bending was achieved by the addition of posterior transpedicular instrumentation. The addition of cross-bracing to the posterior instrumentation had a stabilising effect on axial rotation. The bone density of the adjacent vertebral bodies was a significant factor for stabilisation in flexion and extension and in lateral bending.

STUDY DESIGN A biomechanical human cadaveric study. OBJECTIVE To create a biomechanical model of low-grade degenerative lumbar spondylolisthesis (DLS), defined by anterior listhesis, for future testing of spinal instrumentation. SUMMARY OF BACKGROUND DATA Current spinal implants are used to treat a multitude of conditions that range from herniated discs to degenerative diseases. The optimal stiffness of these instrumentation systems for each specific spinal condition is unknown. Ex vivo models representing degenerative spinal conditions are scarce in the literature. A model of DLS for implant testing will enhance our understanding of implant-spine behavior for specific populations of patients. METHODS Four incremental surgical destabilizations were performed on 8 lumbar functional spinal units. The facet complex and intervertebral disc were targeted to represent the tissue changes associated with DLS. After each destabilization, the specimen was tested with: (1) applied shear force (-50 to 250 N) with a constant axial compression force (300 N) and (2) applied pure moments in flexion-extension, lateral bending and axial rotation (±5 Nm). Relative motion between the 2 vertebrae was tracked with a motion capture system. The effect of specimen condition on intervertebral motion was assessed for shear and flexibility testing. RESULTS Shear translation increased, specimen stiffness decreased and range of motion increased with specimen destabilization (P < 0.0002). A mean anterior translation of 3.1 mm (SD 1.1 mm) was achieved only after destabilization of both the facet complex and disc. Of the 5 specimen conditions, 3 were required to achieve grade 1 DLS: (1) intact, (3) a 4-mm facet gap, and (5) a combined nucleus and annulus injury. CONCLUSION Destabilization of both the facet complex and disc was required to achieve anterior listhesis of 3.1 mm consistent with a grade 1 DLS under an applied shear force of 250 N. Sufficient listhesis was measured without radical specimen resection. Important anatomical structures for supporting spinal instrumentation were preserved such that this model can be used in future to characterize behavior of novel instrumentation prior to clinical trials.

Rollover crashes are dynamic and complex events in which head impacts with the roof can cause catastrophic neck injuries. Ex vivo and computational models are valuable in understanding, and ultimately preventing, these injuries. Although neck posture and muscle activity influence the resulting injury, there is currently no in vivo data describing these parameters immediately prior to a head-first impact. The specific objectives of this study were to determine the in vivo neck vertebral alignment and muscle activation levels when upside down, a condition that occurs during a rollover. Eleven human subjects (6F, 5M) were tested while seated upright and inverted in a custom-built apparatus. Vertebral alignment was measured using fluoroscopy and muscle activity was recorded using surface and indwelling electrodes in eight superficial and deep neck muscles. In vivo vertebral alignment and muscle activation levels differed between the upright and inverted conditions. When inverted and relaxed, the neck was more lordotic, C1 was aligned posterior to C7, the Frankfort plane was extended, and the activity of six muscles increased compared to upright and relaxed. When inverted subjects were asked to look forward to eliminate head extension, flexor muscle activity increased, C7 was more flexed, and C1 was aligned anterior to C7 versus upright and relaxed. Combined with the large inter-subject variability observed, these findings indicate that cadaveric or computational models designed to study injuries and prevention devices while inverted need to consider a variety of postures and muscle conditions to be relevant to the in vivo situation.

An in vitro biomechanical investigation in the human lumbar spine focuses on the functional significance of vertebral bone density and intervertebral disc degenerations.To determine that interrelationship between vertebral bone density and intervertebral disc degeneration, their effect on normal spine motion, and their significance in the biotechnical performance of interbody fixation techniques.A relationship between vertebral bone density and intervertebral disc degeneration has been suggested, but a definitive relationship has not been established. The effect of vertebral bone density and intervertebral disc degeneration on interbody stabilization remains unknown despite the rapidly increasing use of this surgical method for patients with chronic low back pain.The vertebral bone density and intervertebral disc degeneration of 72 functional spinal units were determined using dual energy x-ray absorptiometry scans and macroscopic grading, respectively. A three-dimensional flexibility test was performed on 24 functional spinal units in the intact and stabilised conditions. The compressive behavior of the bone-implant interface was evaluated in 48 functional spinal units.The vertebral bone density in moderately degenerated disc was significantly lower than at all other levels of intervertebral disc degeneration. Increasing intervertebral disc degeneration resulted in more axial rotation and less lateral bending. In flexion-extension and lateral bending, better vertebral bone resulted in significantly better stabilization. This trend was observed also in axial compression in which higher failure loads were observed with greater bone densities.The authors conclude a significant relationship exists between bone density and disc degeneration, bone density is a highly important factor in the performance of interbody stabilization, and disc degeneration, is of moderate importance in signal motion.

Pedicle hooks which are used as an anchorage for posterior spinal instrumentation may be subjected to considerable three-dimensional forces. In order to achieve stronger attachment to the implantation site, hooks using screws for additional fixation have been developed. The failure loads and mechanisms of three such devices have been experimentally determined on human thoracic vertebrae: the Universal Spine System (USS) pedicle hook with one screw, a prototype pedicle hook with two screws and the Cotrel-Dubousset (CD) pedicle hook with screw. The USS hooks use 3.2-mm self-tapping fixation screws which pass into the pedicle, whereas the CD hook is stabilised with a 3-mm set screw pressing against the superior part of the facet joint. A clinically established 5-mm pedicle screw was tested for comparison. A matched pair experimental design was implemented to evaluate these implants in constrained (series I) and rotationally unconstrained (series II) posterior pull-out tests. In the constrained tests the pedicle screw was the strongest implant, with an average pull-out force of 1650 N (SD 623 N). The prototype hook was comparable, with an average failure load of 1530 N (SD 414 N). The average pull-out force of the USS hook with one screw was 910 N (SD 243 N), not significantly different to the CD hook's average failure load of 740 N (SD 189 N). The result of the unconstrained tests were similar, with the prototype hook being the strongest device (average 1617 N, SD 652 N). However, in this series the difference in failure load between the USS hook with one screw and the CD hook was significant. Average failure loads of 792 N (SD 184 N) for the USS hook and 464 N (SD 279 N) for the CD hook were measured. A pedicular fracture in the plane of the fixation screw was the most common failure mode for USS hooks.(ABSTRACT TRUNCATED AT 250 WORDS)

Study design In vivo large animal (pig) model study of cerebrospinal fluid (CSF) pressures after acute experimental spinal cord injury (SCI). Objective To determine how the CSF pressure (CSFP) and CSF pulse pressure amplitude (CSFPPA) cranial and caudal to the injury site change after an acute SCI with subsequent thecal occlusion and decompression. Summary of background data Lowering intrathecal pressure via CSF drainage is currently instituted to prevent ischemia-induced SCI during thoracoabdominal aortic aneurysm surgery and was recently investigated as a potential intervention for acute traumatic SCI. However, in SCI patients, persistent extradural compression commonly occludes the subarachnoid space. This may generate a CSFP differential across the injury site, which cannot be appreciated with lumbar catheter pressure measurements. Methods Anesthetized pigs were subjected to an acute contusive SCI at T11 and 8 hours of sustained compression (n = 12), or sham surgery (n = 2). CSFP was measured cranial and caudal to the injury site, using miniature pressure transducers, during compression and for 6 hours after decompression. Results The cranial-caudal CSFP differential increased (mean, 0.39 mm Hg/h), predominantly due to increased cranial pressure. On decompression, cranial CSFP decreased (mean, -1.16 mm Hg) and caudal CSFP increased (mean, 0.65 mm Hg). The CSFP differential did not change significantly after decompression. Cranial CSFPPA was greater than caudal CSFPPA, but this differential did not change during compression. On decompression, the caudal CSFPPA increased in some but not all animals. Conclusion Although extradural compression exists at the site of injury, lumbar CSFP may not accurately indicate CSFP cranial to the injury. Decompression may provide immediate, though perhaps partial, resolution of the pressure differential. CSFPPA was not a consistent indicator of decompression in this animal model. These findings may have implications for the design of future clinical protocols in which CSFP is monitored after acute SCI.

The cerebrospinal fluid (CSF) is thought to protect the spinal cord from physiologic loading; however, it is unclear whether this protective role extends to traumatic events in which bone fragments enter the canal at high velocity. A synthetic model of the spinal neural anatomy, with mechanical properties similar to native tissues, was constructed to determine if the thickness of the CSF layer (0, 12.8, 19.2 and 24.8mm, 10mm cord) and the velocity (1.2, 2.4, 3.7 and 4.8m/s) of a 20g impactor affect mechanical predictors of spinal cord injury (SCI) severity. Cord compression was directly proportional to impact velocity, inversely proportional to CSF dimension and zero for the largest dura size. The cord was compressed by more than 18% of its original diameter for the "no CSF" condition and the small dura size for all velocities. Impact loads were directly proportional to velocity, and inversely proportional to the thickness of the CSF layer. Peak cord tension increased with dura size and velocity. Peak CSF pressure decreased with distance from the impact epicenter for all dura sizes; attenuation was proportional to the velocity and greatest for the smallest dura. Increased CSF dimension led to reduced CSF pressure near the impact epicenter but had little effect at the remote sites. The results suggest that a thicker CSF layer may reduce the stress induced in the cord, and therefore metrics of SCI risk may be improved by incorporating thecal sac dimensions. Computational, synthetic, cadaveric and animal models may better simulate the biomechanics of human SCI if fluid interaction is incorporated. Language: en

Results of recent imaging studies and theoretical models suggest that the superior femoral neck is a location of local weakness due to an age-related thinning of the cortex, and thus the site of hip fracture initiation. The purpose of this study was to experimentally determine the spatial and temporal characteristics of the macroscopic failure process during a simulated hip fracture that would occur as a result of a sideways fall. Twelve fresh frozen human cadaveric femora were used in this study. The femora were fractured in an apparatus designed to simulate a fall on the greater trochanter. Image sequences of the surface events related to the fractures were captured using two high-speed video cameras at 9111 Hz. The videos were analyzed with respect to time and load to determine the location and sequence of these events occurring in the proximal femur. The mean failure load was 4032 N (SD 370 N). The first surface events were identified in the superior femoral neck in eleven of the twelve specimens. Nine of these specimens fractured in a clear two-step process that initiated with a failure in the superior femoral neck, followed by a failure in the inferior femoral neck. This cadaveric model of hip fracture empirically confirms hypotheses that suggested that hip fractures initiate with a failure in the superior femoral neck where stresses are primarily compressive during a sideways fall impact, followed by a failure in the inferior neck where stresses are primarily tensile. Our results confirm the superolateral neck of the femur as an important region of interest for future hip fracture screening, prevention and treatment research.

A biomechanical study using ex vivo bovine spinal cord and dura, and a synthetic surrogate spinal cord with bovine dura.To investigate the effect of cerebrospinal fluid (CSF) on spinal cord deformation characteristics and to evaluate the biofidelity of a new surrogate spinal cord using an ex vivo bovine model of the burst fracture process.Spinal cord injury is associated with significant personal, economic and social costs. The role of CSF during the injury event and its effect on the spinal cord deformation and neurologic injury is not well understood. Such knowledge could inform preventative strategies and clinical interventions and aid the development and validation of experimental and computational models.The transverse impact of a propelled bone fragment analogue with bovine and surrogate cord models was recorded with high speed video and the images analyzed to determine deformation trajectories. Each cord specimen was tested in 3 states: with dura and CSF, with dura only, and without dura. The effect of these states on deformation magnitude, duration, and energy loss parameters was assessed. RESULTS.: The estimated spinal cord deformation was significantly reduced, although not eliminated, in the presence of CSF when compared to the bare state. The duration of deformation was generally increased in the presence of CSF, though this difference was not statistically significant. This may indicate a reduction in the cord-fragment interaction force for a given impulse. The dura was found to have no significant effect on deformation parameters for the bovine spinal cord. The deformation of the surrogate cord gave similar trends for the different states in comparison to the bovine cord, but was significantly less than the bovine spinal cord for all conditions.The results indicate that the protective mechanism of CSF may not eliminate cord deformationunder the high energy transverse impact characteristic of a burst fracture. However, CSF may contribute to a lessening of cord deformation and applied force.