Search

The primary scope of the present work is the comprehensive investigation of a novel multigeneration system that exploits renewable energy sources, i.e. solar energy, geothermal energy, and biomass, and produces four useful outputs, i.e. electricity, heating, cooling, and green hydrogen. Solar irradiation is the primary energy source, which is exploited by parabolic trough collectors and powers a supercritical CO 2 regenerative Brayton cycle, while a biomass boiler serves as an auxiliary energy input. In addition, the whole installation includes a proton exchange membrane water electrolyzer, a water heater, as well as an absorption chiller, where a geothermal well is used for heat rejection. Apart from the thermal energy storage tank, which is coupled with the collectors, hydrogen production is used as a secondary energy storage method, as the excess produced renewable electricity feeds the electrolyzer. Consequently, the installation is examined parametrically, and optimized on steady-state conditions. Then, a dynamic simulation study is conducted for the climate data of Athens, Greece. According to the results, at the optimum operation point on steady-state conditions, the energy efficiency is determined at 37.89%, and the exergy efficiency at 20.86%. Moreover, the annual energy and exergy efficiencies are defined at 32.52%, and 18.51%, respectively. The economic evaluation analysis indicates that the payback period is about 11 years, while the internal rate of return, and the net present value are determined at 10.62% and 7,753,905 €, respectively. In addition, the system is estimated to save 3072.6 tons of CO 2 equivalent per annum. In conclusion, the proposed multigeneration system can address the various energy needs and recent environmental challenges, as a totally renewable, economically feasible, and environmentally friendly solution. • A multigeneration system that produces four useful outputs is examined. • The unit exploits three renewable sources, solar, biomass, and geothermal. • Both steady-state and dynamic analyses are carried out. • The annual energy and exergy efficiencies are defined at 32.52% and 18.51%. • The system payback period is found at 11 years, while it saves 3072.6 tn CO2-eq. [ABSTRACT FROM AUTHOR]

An innovative parabolic trough concentrator coupled to a twin cavity receiver (PTC-TC) in evacuated tube conditions is investigated thermally and optically. The suggested design is compared with a PTC design with a flat receiver (PTC-F) in order to evaluate the efficiency of the proposed configuration. In the very first stages of the study, the optical efficiency was calculated for both collectors, and the optimum design was determined in the PTC-TC case. Then a mass flow rate independency procedure was conducted to ensure accurate results and to make a suitable comparison. The collectors were examined in a wide range of inlet temperatures ranging from 20 °C to 200 °C, and the thermal performance was calculated. Through the comparison process, it was revealed that the proposed collector appears to have higher thermal performance than the typical collector. In particular, there was a mean enhancement of approximately 8%, while the minimum enhancement was found to be greater than 5%. The simulation results regarding both configurations were verified through two models based on theoretical equations. In both geometries, the mean deviations in the verification procedure were lower than 5.6% in both the Darcy friction factor and the Nusselt number. The design and the simulations were conducted with the SolidWorks Flow Simulation tool. [ABSTRACT FROM AUTHOR]

The aim of the present work is the analysis of a solar-driven unit that is located on the non-interconnected island of Kythnos, Greece, that can produce electricity and green hydrogen. More specifically, solar energy is exploited by parabolic trough collectors, and the produced heat is stored in a thermal energy storage tank. Additionally, an organic Rankine unit is incorporated to generate electricity, which contributes to covering the island's demand in a clean and renewable way. When the power cannot be absorbed by the local grid, it can be provided to a water electrolyzer; therefore, the excess electricity is stored in the form of hydrogen. The produced hydrogen amount is compressed, afterward stored in tanks, and then finally can be utilized as a fuel to meet other important needs, such as powering vehicles or ferries. The installation is simulated parametrically and optimized on dynamic conditions, in terms of energy, exergy, and finance. According to the results, considering a base electrical load of 75 kW, the annual energy and exergy efficiencies are found at 14.52% and 15.48%, respectively, while the payback period of the system is determined at 6.73 years and the net present value is equal to EUR 1,073,384. [ABSTRACT FROM AUTHOR]

The focus of the current study is on a cogeneration unit designed to produce both electricity and hydrogen, which is made up of a parabolic trough collectors' field associated with a storage tank, a recuperative organic Rankine cycle module, and a proton exchange membrane water electrolyzer. The latter system operates using electricity generated by the organic Rankine cycle to produce hydrogen, which can subsequently be used as either a fuel or a storage medium for seasonal storage. The study begins with a thermodynamic investigation under both steady-state and dynamic conditions. The solar field is simulated using the Engineering Equation Solver, while the organic Rankine cycle and the electrolyzer are modeled in Aspen Plus. The analysis extends to economic and environmental evaluations, along with an optimization procedure based on techno-economic criteria. Regarding the optimum design case, the annual net electricity yield is determined at 333.8 MWh, the yearly hydrogen production amount is equal to 6236.6 kg, while the yearly energy efficiency is calculated at 14.9% and the yearly exergy efficiency at 15.9%. Finally, the economic investigation indicates the net present value is about 645,555 €, while the system contributes to saving 198.1 tn CO2-eq during the yearly operation. [Display omitted] • A solar-driven electricity and hydrogen cogeneration unit is investigated. • Thermodynamic, economic, and environmental aspects are examined. • The net electricity production is found at 333.8 MWh per year. • The hydrogen production amount is determined at 6236.6 kg per year. • The investment NPV is 645,555 €, while it saves 198.1 tn CO2-eq per year. [ABSTRACT FROM AUTHOR]

The goal of the present paper is the investigation of a solar desalination system with an organic Rankine cycle system for power and freshwater production. This system is an environmentally friendly technology that is able to utilize solar energy properly in a novel cogeneration application. A parabolic trough concentrator with a smooth and corrugated receiver was employed as the heat source of the desalination system. A humidifier–dehumidifier desalination technology was used for producing freshwater. The electricity is produced by an organic Rankine cycle which is fed both by the solar field and by the hot brine. The present analysis is performed by using a detailed numerical model which is validated by experimental literature data. Based on the final results, the corrugated tube has a maximum performance of 66.59%, and it is more efficient than the smooth tube with 63.11%. The average freshwater productions were estimated equal to 13.09 kg hr−1 and 12.71 kg hr−1 for the corrugated and smooth tubes, respectively. The maximum net work production is found at 7.57 kW with R113, while the less efficient working fluid is R134a. It was found that the application of the developed desalination system leads to the production of high amounts of fresh water and a significant reduction of the equivalent CO2 emissions. [ABSTRACT FROM AUTHOR]

In this study, a solar parabolic trough concentrator (PTC) was evaluated as a heat source of a power generation system based on energy (E1), exergy (E2), environmental (E3), and economic (E4) analyses. Various configurations of power generation systems were investigated, including the solar SRC (SRC) and solar ORC (ORC). Water and R113 were used as heat transfer fluids of SRC and ORC system, respectively. It should be mentioned that the proposed solar systems were evaluated for providing the required power of a mobile house in an emergency condition such as an earthquake that was happened in Kermanshah, Iran, in 2016 with many homeless people. The PTC system was optically and thermally investigated based on sensitivity analysis. The optimized PTC system was assumed as a heat source of the RC with two various configurations for power generation. Then, the solar RC systems were investigated based on 4E analyses for providing the power of the mobile house based on various numbers of solar RC units. It was concluded that the solar SRC system could be recommended for achieving the highest 4E performance. The highest value of its energy efficiency was found at 24.60% and of his exergy at 26.37%. On the other hand, the ORC system has energy and exergy efficiencies at 17.64% and 18.91%, respectively, which are significantly lower than the efficiencies of the SRC system. The optimum heat source temperature for the SRC system is found at 650 K, while for the ORC system at 499 K. Moreover, the best economic performance was found with the SRC system with a payback period of 7.47 years. Finally, the CO2 mitigated per annum ( φ CO 2 ) was estimated at 5.29 (tones year−1), and the carbon credit ( Z CO 2 ) was calculated equal to 76.71 ($ year−1). [ABSTRACT FROM AUTHOR]

The objective of this paper is the investigation of the annual performance of a solar power plant with linear Fresnel reflectors in the El-Oued region at Algeria. The solar collectors produce water steam that feeds a turbine to produce electricity. The System Advisor Model (SAM) tool is used for simulation. The mean net daily electricity production rate from 8:30 am to 5:30 pm is 48 MWe, and the respective annual production is 210,336 MWh/year. The mean daily optical efficiency of the solar field was close to 52%, while the mean thermal efficiency was about 39%. The net daily cycle efficiency is found to be 24%. The net capital cost of the examined system is $393 million, and the developer net present value is $47 million; the investor net present value is $15 million, the entire period of capital recovery is 11 years, and the levelized cost of electricity is 0.0382 $/kWh. The solar power plant leads to the yearly avoidance of 420,672 tons carbon dioxide emissions (operational cost savings of $6.1 million). Based on the obtained results, linear Fresnel reflectors can be used to achieve satisfying, energetic, financial, and environmental performance that can lead to sustainability. [ABSTRACT FROM AUTHOR]

The parabolic trough solar collector (PTC) is the most mature solar concentrating technology, and this technology is applied in numerous thermal applications. Usually, the thermal efficiency of the PTC is expressed with the aid of polynomial expressions. However, there is not a universal expression that is applied in all cases with high accuracy. Many studies use expressions with the first-degree polynomial, second-degree, or fourth-degree polynomial expressions. In this direction, this work is a study that investigates different expressions about the thermal efficiency of a PTC with a systematic approach. The LS-2 PTC module is examined with a developed numerical model in the Engineering Equation Solver for different operating temperatures and solar beam irradiation levels. This model is validated using experimental literature data. The found data are approximated with various polynomial expressions with up to six unknown parameters in every case. In every case, the mean absolute percentage error and the R2 are calculated. According to the final results, the use of the third power term leads to the best fitting results, as well as the use of the temperature difference term (ΔΤ), something that is new according to the existing literature. More specifically, the final suggested formula has the following format: "ηcol = a0 + a3∙ΔT3/Gb + b∙ΔΤ". The results of this work can be used by the scientists for the optimum fitting of the PTC efficiency curves and for applying the best formulas in performance determination studies. [ABSTRACT FROM AUTHOR]

In the present investigation, a solar parabolic trough concentrator (PTC) with a linear cavity was examined by using a developed numerical model. More specifically, a V‐shape cavity receiver was studied in this work as a new and alternative design. The use of a cavity in a PTC is a very promising idea because it leads to high efficiency and to low investment cost. Up today, the emphasis in the use of cavities is given in dish concentrators and so there is a need for investigation of cavities also in linear concentrators. Different dimensional and operational parameters of the PTC with a V‐shape cavity were considered. More specifically, the position, aperture area, and the tube diameter of the V‐shape cavity, solar irradiance, inlet temperature level, and mass flow rate were evaluated based on sensitivity analysis. The results revealed that the highest optical performance was attained when the cavity was placed at the PTC focal line. Moreover, it is found that there is an optimum cavity aperture area to determine the greatest thermal efficiency. For the optical errors of 5, 10, 15, 20, and 35 mrad, the optimum cavity aperture wide was calculated at 5, 5, 6, 7, and 8 cm, respectively, with the tracking error to be 0°. The highest thermal performance has found when the collector operates with low inlet temperature, high flow rate, high solar irradiation level, and small cavity tube diameter. [ABSTRACT FROM AUTHOR]

The objective of this study is the investigation of different solar concentrating collectors for application in a trigeneration system. Parabolic trough collectors, linear Fresnel reflectors and solar dishes are the examined solar concentrating technologies in this work. The trigeneration unit includes an organic Rankine cycle coupled with an absorption heat machine that operates with LiBr/water. The analysis is performed throughout the year by using the weather data of Athens in Greece. The results of this work indicate that the selection of parabolic trough collectors is the best choice because it leads to the maximum yearly system energy efficiency of 64.40% and to the minimum simple payback period of 6.25 years. The second technology is the solar dish with the energy efficiency of 62.41% and the simple payback period of 6.95 years, while the linear Fresnel reflector is the less efficient technology with the energy efficiency of 35.78% and with a simple payback period of 10.92 years. Lastly, it must be stated that the thermodynamic investigation of the system is performed with a created model in Engineering Equation Solver, while the dynamic analysis is performed with a code in the programming language FORTRAN. [ABSTRACT FROM AUTHOR]

Abstract Parabolic trough collector (PTC) is the most established solar concentrating technology worldwide. The conventional parabolic trough collectors are used in various applications of medium and high-temperature levels. However, there are numerous studies which investigate alternative designs. The reasons for examining different PTC configurations regard the thermal efficiency increase, the reduction of the manufacturing cost and the development of more compact designs. The objective of this review paper is to summarize the existing alternative designs of PTC and to suggest the future trends in this area. Optical and thermal modifications are examined, as well as the use of concentrating thermal photovoltaic collectors. The optical modifications include designs with secondary concentrators, stationary concentrators and strategies for achieving uniform heat flux. The thermal modifications regard the use of nanofluids, turbulators and the use of thermally modified receivers with insulation, double-coating and radiation shields. The concentrating thermal photovoltaics are systems with flat or triangular receivers which can operate in low or in medium temperature levels with the proper alternative designs. It has been found that there are many promising choices for designing PTC with higher thermal performance and lower cost. The conclusions of this work can be used as guidelines for future trends in linear parabolic concentrating technologies. [ABSTRACT FROM AUTHOR]

Highlights • A secondary booster reflector is examined in a parabolic trough collector. • The optical enhancement is found to be higher in greater incident angles. • The optical enhancement is greater during the winter period. • The yearly enhancement is found to be 21.7% for Athens, Greece. • The thermal enhancement is more intense in higher operating temperatures. Abstract The objective of this work is the investigation of a novel booster reflector in a parabolic trough collector (PTC). More specifically, a vertical secondary booster reflector is located at the end of the trough in order to enhance the optical performance of the solar collector. This extra concentrator reduces the end optical losses of the PTC by reflecting back them in the receiver. Moreover, it acts as an extra reflecting area which captures extra solar beam irradiation in the cases with a non-zero incident angle. The collector is examined optically and thermally in order to determine both the optical and the thermal gain by the use of this novel idea. The overall analysis is conducted for steady-state conditions, as well as the yearly evaluation of the suggested idea is given. According to the final results, the use of the extra booster leads always to optical and thermal enhancement, especially in greater incident angles. The yearly optical enhancement, for a collector with a focal distance to length ratio of 0.236, is calculated at 21.7% and it is more intense in the months with greater incident angles. More specifically, it was calculated at 8.7% in June, 24.2% in September and 77.1% in December. The thermal analysis proved that the thermal enhancement is greater than the optical and it is higher when the system operates with great fluid temperature levels. [ABSTRACT FROM AUTHOR]

Solar concentrating solar thermal collectors are promising technologies for various applications which demand medium- and high-temperature levels. The objective of this work is to review the recent trends in the solar concentrating collectors and to give the emphasis on the performance enhancement methods which applied to the concentrating technologies. Optical and thermal enhancements methods are investigated for the following collector types: compound parabolic concentrator, parabolic trough collector, linear Fresnel reflector and solar dish concentrator. The emphasis is given to the utilization of nanofluids as working fluids because a lot of research has been focused on them in the last years. Moreover, the use of internal fins and inserts in the flow, the use of modified absorbers, as well as various optical design optimizations are included in this review. The final conclusions of this work clearly indicate the most effective enhancement methods in the concentrating solar collectors, as well as the future fields that have to be investigated. [ABSTRACT FROM AUTHOR]

The use of nanofluids in parabolic trough collectors is one of the most promising techniques for enhancing their performance. The objective of this work is to investigate the use of various nanoparticles (Cu, CuO, Fe2O3, TiO2, Al2O3 and SiO2) dispersed in thermal oil (Syltherm 800). A detailed parametric analysis is performed for flow rates from 50 to 300 L min−1, for inlet temperatures from 300 K to 650 K and for nanoparticle concentrations up to 6%, while the impact of the solar irradiation level on the thermal efficiency enhancement is also investigated. Moreover, a new index for the working fluid evaluation in solar collectors is introduced. The analysis is conducted with a developed thermal model in Engineering Equation Solver. According to the final results, the most efficient nanoparticle is the Cu, with CuO, Fe2O3, TiO2, Al2O3 and SiO2 to follow, respectively. It is found that the higher enhancement is observed for lower flow rates, higher inlet temperatures and higher nanoparticle concentrations, while it is approximately constant for the different solar irradiation levels. For the typical operating conditions with 150 L min−1 flow rate and 600 K inlet temperature, the thermal efficiency enhancement is found 0.31, 0.54 and 0.74% for Cu concentrations 2, 4 and 6%, respectively. [ABSTRACT FROM AUTHOR]

Parabolic trough collector is one of the most usual solar collectors for applications up to 400 °C. The thermal enhancement of this collector concentrates a lot of interest and various techniques are tested in order for the thermal efficiency to be maximized with a reasonable penalty in the pressure drop. The use of nanofluids as working fluids, as well as the use of flow turbulators, mainly inserts and internal fins or tube dimples are the main techniques which are examined. The objective of this work is to give a complete literature review of the existing studies on this domain and to present a numerical comparative analysis between the most usual thermal enhancement techniques. More specifically, the use of oil-based nanofluids with 6% CuO is compared with the use of internal rectangular fins in the absorber, while the combination of these techniques is also examined. The analysis is conducted with a validated CFD model in SolidWorks Flow Simulation for various fluid temperature levels. According to the final results, the use of nanofluids leads to 0.76% thermal efficiency enhancement, the use of internal fins to 1.10% and the combination of these techniques to 1.54%. Moreover, emphasis is given in the pressure drop of the examined cases and in the evaluation criteria which are used in every case. [ABSTRACT FROM AUTHOR]

Parabolic trough collector is an emerging solar technology for achieving the sustainability. Numerous studies have been focused on their performance evaluation and many techniques have been suggested for improving their thermal efficiency. The objective of this paper is to determine the impact of various thermal enhancement techniques on the thermal efficiency improvement of the PTC. The most usual techniques for increasing the thermal performance of parabolic trough collectors are the use of inserts, internal fins, metallic foams and the dimpled absorbers. A parametric analysis is conducted using different values of the thermal enhancement ratio (Nusselt number to the Nusselt number of the smooth absorber case). According to the final results, the thermal efficiency enhancement can reach up to 2% when the Nusselt number is about 2.5 times greater compared to the reference case and the inlet temperature is equal to 600 K. Moreover, in this case, the thermal losses are approximately 22% lower than in the respective reference case. For higher Nusselt number ratios, the thermal enhancement presents relatively small increase. This analysis is performed with a developed thermal model in Engineering Equation Solver (EES) which is validated with the literature results. [ABSTRACT FROM AUTHOR]

Parabolic trough collector (PTC) is the most mature concentrating technology which is used in a great variety of thermal applications. In this study, the daily performance of a PTC is investigated for all the year period. The module of Eurotrough parabolic trough collector is examined with various storage tanks from 3 m 3 to 15 m 3 and the collector performance is investigated in energetic and exergetic terms. An Input/Output method is applied for the daily evaluation of the solar thermal system, something innovative for concentrating solar collectors. According to the final results, different storage tank volumes lead to similar thermal outputs but to extremely different exergetic outputs because of the high dependence of the mean storage tank temperature with the storage tank volume. For the storage tank of 9 m 3 , the mean thermal efficiencies in December and in June are found to be 37.1% and 68.7% respectively, while the mean exergetic efficiencies 2.0% and 8.5% respectively. Moreover, it is proved that the Input/Output performance method in concentrating collectors has to take into consideration the solar incident angle at solar noon in order high accuracy to be achieved. [ABSTRACT FROM AUTHOR]

Parabolic trough collector is one of the dominant emerging solar technologies for producing heat at high temperatures (usually 200–400 °C). The objective of this study is to investigate the thermal performance of internally finned absorbers. Twelve different fin geometries are examined and compared with the smooth absorber case for various operating scenarios. More specifically, the investigated internal fins have thicknesses 2 mm, 4 mm and 6 mm, while their lengths are 5 mm, 10 mm, 15 mm and 20 mm. The examined parameters for the evaluation of the internally finned absorbers are the thermal efficiency, the Nusselt number, the pressure losses, as well as the thermal enhancement index. According to the final results, higher fin thickness and length lead both to higher thermal performance and simultaneously to higher pressure losses. The impact of the length on the results is found to be more intense than the thickness. According to the thermal enhancement index, the case with 20 mm length and 4 mm thickness is found to be the optimum case. For this absorber, the increase in the thermal efficiency and the thermal enhancement index are found 1.27% and 1.483 respectively for 600 K inlet temperature, while the Nusselt number is proved to be 2.65 times greater than in the smooth case. [ABSTRACT FROM AUTHOR]

Among the solar concentrating technologies, parabolic trough collector (PTC) is the most mature and cost-effective technology for medium and high-temperature levels (150–400 °C). This paper investigates the utilization of internally finned absorbers in LS-2 PTC module for various operating conditions. Twelve different longitudinal fins are tested and compared with the smooth case. The analysis is performed with SolidWorks Flow Simulation, using a validated model by literature results. Generally, it is proved that both greater length and thickness lead to higher thermal enhancement and to higher pressure losses. Various methods are presented for evaluating together the thermal efficiency or Nusselt number enhancement versus the increase in pressure drop or in the friction factor. Taking into consideration four different criteria, the absorber with 10 mm fin length and 2 mm fin thickness is found to be the overall optimum case. For this case, the thermal efficiency is enhanced about 0.82%, the Nusselt number increase 65.8%, while the friction factor and the pressure losses are about the double compared to the smooth case. [ABSTRACT FROM AUTHOR]

The objective of this study is to present a detailed exergetic analysis of the commercial parabolic trough collector LS-2. A complete thermal model is developed in EES (Engineering Equation Solver) and it is validated with literature results. The solar collector is examined for operation with Therminol VP1 and air in order to examine the most representative liquid and gas working fluids. In the exergetic analysis, detailed presentation of the exergetic losses and the exergy destruction is given for various operation cases. More specifically, different combinations of flow rates and inlet temperature levels are tested for both working fluids and the results indicate the reasons for the exergetic reduction in every case. According to the final results, the global maximum exergetic efficiency for operation with air is 25.62% for an inlet temperature of 500 K and flow rate of 10,000 l/min, while for Therminol VP1 is 31.67% for 500 K and 100 l/min. Moreover, it is proved that the exergy destruction is more intense in the thermal oil case, while the exergetic losses are more important in the air case. The final results and conclusions clearly present the exergetic analysis of parabolic trough collector for a great range of operating conditions. [ABSTRACT FROM AUTHOR]

In this study, a solar driven trigeneration system is investigated and optimized in energetic and exergetic terms. Parabolic Trough collectors (PTC) are used for supplying the demanded heat input in the present configuration which includes a storage tank, an Organic Rankine Cycle (ORC) module and an absorption heat pump operating with the LiBr-H 2 O working pair. The heat source from solar collectors drives the ORC which rejects heat to the generator of the absorption heat pump. This heat pump produces heating and cooling demand simultaneously, while electricity is produced from the ORC. The examined system is analyzed parametrically in steady state conditions with Engineering Equator Solver (EES) tool by keeping the collecting area equal to 1000 m 2 in all the examined cases. Eight different working fluids are tested in the ORC, while six extra design parameters are studied. The inlet temperature in the heat recovery system, the superheating, the maximum pressure in ORC, the heat rejection temperature of ORC, the evaporating temperature of the heat pump, as well as the solar beam irradiation are the examined parameters. According to the final results, toluene is the working fluid which leads to maximum exergetic output with n-octane and MDM to follow with 29.42%, 28.50% and 28.35% respectively. In the optimum case, the electricity production of the system is 177.6 kW el , while the cooling and the heating outputs are 398.8 kW and 972 kW respectively. [ABSTRACT FROM AUTHOR]

The objective of this study is to determine the energetic and exergetic enhancement of parabolic trough collector with internal fins in the absorber. Carbon dioxide is the examined working fluid to investigate the performance of the system in high temperature levels. In the first part of this study, the impact of the mass flow rate on the collector performance is analyzed and finally 0.20 kg/s is selected as the most appropriate mass flow rate exergetically. In the second part, the impact of internal fins on the system performance is investigated for operation with the optimum mass flow rate. More specifically, the absorber without fins is compared with three different fins with lengths 5, 10 and 15 mm. The final results prove that the higher fin length increases the thermal performance, while the optimum fin length exergetically is 10 mm with 45.95% exergetic efficiency when the inlet temperature is equal to 400 °C. The impact of the pressure losses along the collector is taken into account in the exergetic efficiency, which is the best index for evaluating solar collectors operating with gases. The analysis is performed with Solidworks Flow Simulation, a powerful tool which allows the simultaneous thermal and optical analysis. [ABSTRACT FROM AUTHOR]

The use of solar thermal energy for electricity production is a clean and sustainable way to cover the increasing energy needs of our society. The most mature technology for capturing solar energy in high temperature levels is the parabolic trough collectors (PTC). In this study, an Organic Rankine Cycle (ORC) coupled with PTC is analyzed parametrically in order to be optimized financially and energetically. The first step is the thermodynamic investigation of the ORC by using various working fluids. The second step is the energetic and financial investigation of the total system which includes the solar field, the storage tank and the ORC module. By testing many combinations of collecting areas and storage tank volumes, finally cyclohexane proved to be the most suitable working fluid for producing 1 MW el with PTC. Specifically, in the optimum situation a solar field of 25,000 m 2 with storage tank of about 300 m 3 leads to a payback period of 9 years and to an internal rate of return (IRR) equal to 13.46%. Moreover, an economic comparison for different commercial collectors is presented, with Eurotrough ET-150 being the financially optimum solution for this case study. [ABSTRACT FROM AUTHOR]

The integration of solar energy systems is crucial to achieving the global goals for sustainability as well as the reduction of greenhouse gases and pollutants emissions. In this direction, the development of multigeneration systems is very important as they can cover the increasing and numerous demands of modern society in a high-efficient way. In parallel, hydrogen is a promising alternative fuel that has gained attention recently because it can substitute conventional energy sources. So, the objective of the present work is the review, classification, discussion, and comparison of solar-driven multigeneration systems that include hydrogen production. This study is a novel one because it is focused on the integration of hydrogen generation methods into polygeneration systems, while existing publications present the useful outputs of the units, without specialization. In parallel, it meets the increasing need for the investigation of hydrogen energy potential. Apart from hydrogen, other common useful outputs are electricity, heating, cooling, domestic hot water, and freshwater. In this work, the plants are classified according to the hydrogen production method. In parallel, different types of solar devices, such as thermal collectors, photovoltaics, and thermal photovoltaics as well as other additional energy sources are also examined. So, numerous configurations are investigated comprehensively, which can produce a plethora of useful outputs, as well as include thermodynamic cycles, such as Rankine cycles, organic Rankine cycles, and other devices, such as absorption chillers, or desalination units. All the units are evaluated and compared in terms of energy, and exergy performance as well as economic viability, and hydrogen production rate. In general, solar tower-based and parabolic trough collector-based units are high-efficient energetically and exergetically, while concentrating photovoltaic thermal plants achieve high energy efficiency. Finally, suggestions for future research and development are made. • Solar-driven multigeneration systems with hydrogen production are investigated. • The systems are mainly classified according to the hydrogen generation methods. • Solar collectors, photovoltaics, and hybrid solar devices are examined. • Hybridization with auxiliary energy sources is also presented. • Solar towers, PTC, and CPVT are the most efficient systems. [ABSTRACT FROM AUTHOR]

Solar irradiation is a major contributor to renewable energy sources and its utilization is vital for designing a sustainable and green energy network. Greece is a country with high solar potential and thus the exploitation of solar irradiation in this country is an urgent need in order to reduce fossil fuel utilization. Moreover, the increase in solar energy exploitation will lead to the mitigation of environmental policy goals for cleaner energy production processes. To date, Greece exploits solar irradiation mainly with flat plate collectors for low-temperature heating applications and with photovoltaics, while there are no installations including concentrating solar systems although they are attractive technologies. The objective of the present review paper is to demonstrate and to discuss the present steps in the domain of solar concentrating systems in Greece, as well as to suggest future steps aiming to increase the solar energy contribution in this country. More specifically, this work includes studies about parabolic trough collectors, linear Fresnel reflectors, compound parabolic concentrators, solar dishes, solar tower and concentrating thermal photovoltaics. The existing situation regarding solar energy utilization in Greece is collaborated and predictions about future perspectives are provided. It is concluded that although much research interest has been devoted to installations in Greece, no real solar concentration systems are currently in operation. Moreover, the existing studies indicate that solar concentrating systems lead to sustainable and viable investments with acceptable payback period time in the range of 5–7 years. As a result, it is suggested that this is the time to proceed in the next step of the development of real solar concentrating installation in Greece. • All the solar concentrating systems for the Greek climate are included in this review. • Applications for power, refrigeration, heating and polygeneration are presented. • Up today, many theoretical studies have been conducted for Greek solar systems. • In the future, there is a need for real applications and experimental studies. • The examined cases are found to be viable for the climate conditions of Greece. [ABSTRACT FROM AUTHOR]

• Solar-driven polygeneration systems are summarized and discussed in detail. • Photovoltaics, concentrating and non-concentrating solar systems are examined. • Parabolic trough collectors and concentrating thermal photovoltaics are the best cases. • The use of vapor compression heat pumps leads to viable investments. • High exergy efficiency is found in the systems with electrolyzer or gasifier. Solar energy exploitation is an important weapon for facing critical problems such as fossil fuel depletion, global warming and the increasing energy demand due to the new lifestyle trends. Moreover, the increase in the performance of energy systems is another way of achieving sustainability. Polygeneration systems are highly efficient systems that can produce multiple useful energy outputs like electricity, cooling, heating, fresh water and hydrogen. So, combing solar energy systems and polygeneration units is an optimal way of producing many useful outputs with high efficiency and by utilizing a clean energy source. In this direction, the objective of the present work is to review and to discuss the present literature studies about the exploitation of solar irradiation in polygeneration systems. The present review paper investigates the use of different solar energy technologies in any kind of polygeneration system. More specifically, flat plate collector, evacuated tubes, parabolic trough collector, linear Fresnel reflector, solar dish concentrator, solar tower and thermal photovoltaics are the investigated systems in this work. The examined polygeneration systems include various engineering devices like organic Rankine cycle, gas turbine, absorption heat pump, distillation unit, electrolyzer and heat exchanger. The final results indicate that solar-driven polygeneration systems with parabolic trough collectors, concentrating thermal photovoltaics and solar tower can be sustainable and viable systems for application in the future energy commodities. [ABSTRACT FROM AUTHOR]

The utilization of solar irradiation in the building sector is vital to create sustainable systems. Trigeneration systems are highly efficient systems that usually produce electricity, heating and cooling which are the main energy needs in the buildings. The objective of this work is the energetic and financial investigation of three different solar-driven trigeneration systems that can be applied in buildings with high energy needs (e.g., hospitals or commercial buildings). The parabolic trough solar collector (PTC) is selected to be used because it is the most mature solar concentrating technology. The examined configurations practically are different combinations of organic Rankine cycle (ORC) with heat pumps. System 1 includes a PTC coupled to an ORC which feeds an absorption heat pump machine. System 2 includes a PTC which simultaneously feeds an ORC and absorption machine. System 3 includes a PTC which feeds an ORC and a heat exchanger for heating, while the ORC is fed with and electricity a vapor compression cycle for cooling production. The simple payback period of System 1 is 5.62 years and it is the lowest, with System 2 to have 7.82 years and System 3 to have 8.49 years. The energy efficiency of the three systems is 78.17%, 43.30% and 37.45%, respectively, while the exergy efficiency 15.94%, 13.08% and 12.25%, respectively. System 1 is the best configuration according to energy, exergy and financial analysis. This study is performed with developed thermodynamic models in Engineering Equation Solver and a dynamic model in FORTRAN. [ABSTRACT FROM AUTHOR]

This article presents a simulation study which focuses on the thermodynamic analysis of a solar-driven trigeneration system for heating, cooling, and electricity production. The system uses parabolic trough collectors operating with Therminol VP-1 for feeding an organic Rankine cycle operating with toluene and an absorption heat pump operating with a LiBr–H2O working pair. The collecting area is selected at 100 m2 and the storage tank at 4 m3. The system is studied parametrically in order to examine the impact of various parameters on the system energy efficiency, system exergy efficiency, electricity production, heating production, and cooling production in the simple payback period of the investment. The examined parameters are the following: solar beam irradiation level, solar beam irradiation angle, superheating degree in the turbine inlet, pressure level in the turbine inlet, heat source temperature level, generator temperature level, and the heat input in the generator. For the nominal case of a 15 kW generator input, the electricity production is 6.3 kW, the heating production 11.5 kW, and the cooling production 10.7 kW. The system energy efficiency is 40.7%, while the system exergy efficiency is 12.7%. The financial investigation of the investment proved that it is viable with the simple payback period to be 8.1 years in the nominal case and it can be reduced to 7.8 years with an optimization procedure. Lastly, it has to be said that the examined system is found to be a viable configuration which is an ideal choice for application in the building sector. The analysis was conducted under steady-state conditions with a model developed using Engineering Equation Solver (EES). [ABSTRACT FROM AUTHOR]

• A solar-driven polygeneration unit with CO 2 as the working fluid is investigated. • Initial optimization in steady-state conditions and secondary dynamical analysis. • The payback period is found to be around 6.4 years and the total efficiency is 55%. • The use of an extra ORC can be used for enhancing electricity production. • The exergy efficiency with ORC is found 23.63%, while without 23.37%. The object of this study is the investigation of polygeneration plants utilizing solar energy in order to produce power products on the scale of a few MW. Parabolic trough collectors are used in order to exploit solar irradiation and to provide the generated heat to the polygeneration/trigeneration cycle in a high-temperature range (500–570 °C). The plants under consideration additionally consist of a storage tank, a Brayton cycle with s-CO 2 , a LiBr-H 2 O absorption chiller and also the installation of a suitable thermodynamic organic Rankine cycle (ORC) cycle is examined in order to utilize waste heat for further power generation. The systems are first investigated for operation under steady-state conditions and then for dynamic conditions on an annual basis. Based on the final annual results of the plants, the plant in which ORC was not used shows annual electrical, exergy and energy efficiencies equal to 18.33%, 23.37% and 54.91% respectively, while the plant in which ORC was used similarly shows 19.05%, 23.63% and 49.00%. According to economic analysis, the payback period was found at 6.37 years without ORC and 6.51 years with ORC. Taking into account the operational and techno-economic results of the plants it can be concluded that the plants produce satisfactory energy products ensuring also the economic viability of the investment. [ABSTRACT FROM AUTHOR]

• Solar-biomass supercritical CO 2 trigeneration system is studied. • Energetic analysis and selection of optimal conditions for the proposed unit. • Assessment of financial viability for installation in refrigeration application. • Determination of performance results for annual operation in Athens climate. • Production of 185.59 MWh yearly with at least 519 k€ savings during the lifetime. The ever-growing increase of the energy demand required to satisfy the needs of society has aroused considerable interest regarding the investigation of polygeneration systems that employ renewable energy sources. In the present work, the concept of installing a supercritical CO 2 trigeneration system to cover the needs of a refrigerated warehouse in Athens with simultaneous production of power and heating is studied in terms of energy performance, and its financial benefits compared to the solution of an ejector refrigeration-only system are analyzed and assessed. The trigeneration system utilizes solar energy in parabolic trough collectors and biomass energy as the supplementary source, in order to increase the temperature of high-pressure CO 2 and produce power in the turbine which is coupled to a generator. Regarding the collectors, the installation of zero up to four solar modules that exploit the solar power is examined, while the rest energy input needed in order to achieve the selected operating conditions is supplied by a biomass boiler. Since all the trigeneration cases require the same amount of energy input to reach the desired conditions, the trigeneration system for every combination of solar modules is found to produce 185.59 MWh annually, while the refrigeration-only system is found to consume 172.94 MWh during a year. The power production efficiency, the combined power and refrigeration production efficiency and the total trigeneration efficiency for the selected nominal conditions are calculated 11.77 %, 66.09 % and 163.70 % respectively. The case of a trigeneration system with four solar collectors displays a payback period of 4.0 years compared to the refrigeration-only case, providing financial savings equal to 542 k€ for the duration of the project lifetime. The same case compared to that of trigeneration system using only biomass boiler and no solar collectors exhibits payback period of 13.5 years, achieving financial savings of 22.9 k€ for the considered lifetime of the project. [ABSTRACT FROM AUTHOR]

Solar energy is an auspicious renewal energy source because of its abundant availability and its flexibility to be converted into heat or into electricity. Concentrated solar power technologies are promising units for producing electricity in large scale applications and parabolic trough solar collector is the most matured technology for these plants. The objective of this paper is to summarize and to discuss the current status of parabolic trough collector commercial power plants around the world and the technological developments in various constituents of such concentrated solar power plants. More specifically, this review includes various developments in the concentrators and receiver tubes in order to enhance both the thermal and the optical efficiencies. Moreover, the different existing and newly developed heat transfer fluids are discussed in this work and the emphasis is given in the discussion of the different operating temperature levels, the storage system and the applications that use different fluids. Furthermore, different tracking options of the parabolic trough solar collector are examined, different storage technologies, as well as various power cycles and their modifications to enhance the overall efficiency of the parabolic trough collector-based power plants are discussed in detail. The final conclusions of this work indicate the recent developments and the future designs of the parabolic trough solar collector power plants. [ABSTRACT FROM AUTHOR]

The concentrating solar systems of linear Fresnel reflectors offer the ability to generate electricity from solar energy. The main objective of this paper is to perform a transient numerical simulation on a linear Fresnel solar reflector directed to produce superheated water steam for the power plants, in order to determine its efficiencies (optical and thermal), where the heat transfer fluid mass flow inside the copper absorber tube is 0.045 kg/s. The dimensions of the studied linear Fresnel solar collector are the same dimension as the modular system Nova-1 of NOVATEC SOLAR Company. The dimension of the studied model is 1D. For this purpose, El-Oued region has been designated as a study field. The twelve recommended average days for months have been selected for the study. This paper was based on a numerical solution using the finite differences method. MATLAB has been used as a software language. The optical efficiency of the LFR solar receiver has reached 53.7% where the thermal efficiency has reached 37.5%, while the pressure drop within the absorber pipe has reached 02 bars. As for superheated steam temperatures variations, it ranged between 233.35 °C and 263.75 °C, knowing that the water steam inlet temperature when entering the absorber tube is equal to 140 °C. As for the overall coefficient of heat loss, its mean value is 5.84 W/m2.°C. The results obtained are very encouraging to invest in this steam power plant, especially in the desert areas, which are rich in solar energy. Image 1 • Optical efficiency of the solar reflector obtained was 53.7% • Thermal efficiency of the solar reflector achieved was 37.5% • An annual electricity capacity of more than 2000 MW can be produced • This technique is 100% clean and has no negative environmental impact [ABSTRACT FROM AUTHOR]

The present study is a 4E (Energy, Exergy, Economic, and Environmental) analysis of a nanofluid-based parabolic trough collector (PTC) which is conducted with a developed model in MATLAB. MXene (Ti 3 C 2) nanoparticles were added to the silicon oil at weight concentrations of 0.05, 0.08, and 0.1%. The result was the important enhancement of the thermal conductivity of the nanofluid on the rand of 70%–89% for the highest concentration. According to the results, the PTC's optical efficiency was estimated at 79%, while thermal and exergy efficiencies of 74.71% and 22.44% with 0.10 wt% concentration were recorded on July 17, 2019. It is found that the MXene based silicone oil can reduce the system's cost by 0.021 M$ and enhance the energy gained by 1.51% at 0.10 wt% concentration compared to pure oil. Also, the annual CO 2 mitigation from the energy side varies from 2.25 to 2.30-ton CO 2 /year, while the annual environmental gain ranged between 32.73 and 33.28 $/year and 9.065 to 9.102 $/year for the energy and exergy studies respectively. [Display omitted] • A nanofluid-based parabolic trough collector is studied with MXene. • The collector thermal efficiency enhancement is found up to 1.1%. • For the day July 17, 2019, the exergy efficiency was improved from 0.07% to 15.16%. • For energy analysis, the annual CO 2 mitigation varies from 2.26 to 2.30 ton CO 2. • The environmental gain from the energy analysis varies from 32.73 to 33.28 $/year. [ABSTRACT FROM AUTHOR]

The organic Rankine cycle (ORC) is an effective technology for power generation from temperatures of up to 400 °C and for capacities of up to 10 MW el. The use of solar irradiation for driving an ORC is a promising renewable energy-based technology due to the high compatibility between the operating temperatures of solar thermal collector technologies and the temperature needs of the cycle. The objective of this review paper is to present and discuss the operation principles of solar-ORC technology and the wide range of solar-ORC systems that have been studied in the literature. Various solar thermal technologies that can drive the ORC are investigated, such as the flat plate collector, evacuated tube collector, compound parabolic collector, parabolic trough collector, linear Fresnel reflectors, dish concentrators and solar towers. Both simulation studies and experimental investigations are included in the study. Hybrid systems and different thermal storage techniques are also examined in detail. Moreover, systems with ORC which produce many useful outputs such as cooling, heating and fresh water are studied because they present high sustainability indexes. The limitations of the technology are also highlighted, along with critical suggestions aimed at steering future research in this field. The final conclusions indicate that the development of trigeneration and polygeneration systems with ORC sub-systems is a promising avenue, not only for the future development of solar-ORC technology but also for the development of renewable and sustainable energy systems in a broader context. • Solar driven organic Rankine cycles are summarized and discussed in detail. • Concentrating and non-concentrating solar thermal systems are included. • Parabolic trough collector is the best solar technology for power production. • The use of solar organic Rankine cycles in polygeneration is a promising idea. • There is a need for conducting future experimental studies in a great scale. [ABSTRACT FROM AUTHOR]

• A parabolic trough collector with a linear V-Shape cavity receiver was studied. • The V-Shape cavity receiver was coupled with an organic Rankine cycle system. • The solar organic Rankine cycle system was evaluated exergetically and financially. • The optimum turbine inlet temperature is 592 K and the optimum pressure 6 MPa. • The simple payback period was found close to 6.01 years for the large scale setup. In this research, a parabolic trough concentrator with linear V-Shape cavity receiver was studied as the heat source of an organic Rankine cycle system. The solar organic Rankine cycle system was evaluated under exergy and economic analyses. Thermal oil was used as the solar working fluid, and ethanol was used as the organic working fluid under different turbine inlet temperatures and turbine inlet pressure. The influence of different operational parameters, including solar radiation, mass flow rate, and inlet temperature of solar working fluid was investigated on the performance of the solar organic Rankine cycle system. It was found that exergy gain and exergy efficiency of the solar system improved with increasing solar radiation, increasing inlet temperature, and decreasing the flow rate of the solar working fluid. The highest organic Rankine cycle efficiency and total efficiency were found to be 35%, and 25% at turbine inlet temperature of 592 K and turbine inlet pressure of 6 MPa, respectively. Finally, the lowest levelized cost of electricity, and the lowest payback period were calculated equal to 0.0716 (€/kWh), and 8.79 (years) for the optimum condition of the developed solar organic Rankine cycle system, respectively. The present study is beneficial for improving the performance of the solar organic Rankine cycle systems with parabolic trough concentrators in a simple and convenient way and the development of solar thermal technologies. [ABSTRACT FROM AUTHOR]