Search

The improvements in signal-to-noise ratio (SNR) are indispensable to obtain the desired output signal of partial discharge (PD) under square wave pulsewidth modulation (PWM) voltage. In this article, the effect of complex PWM voltage parameters (rise time, fall time, frequency, duty cycle) on the SNR of PD tests is investigated. The results revealed that the sensor's high-frequency gain should be increased to improve the SNR under faster switching. PD impulses are more likely to be submerged in the residual interference under high-frequency voltage. The SNR can be improved by only detecting the PD at the rising front because the PD signal overlaps with commutation noise at the falling front of short duty cycle voltage, such as 0.03% duty cycle. The above results can reference the PWM parameters and improve the SNR in PD tests for rotating machines controlled by power electronics. [ABSTRACT FROM AUTHOR]

Partial discharge (PD) detection plays a vital role in on-line condition monitoring of electrical apparatus in the power systems. However, the noise of PD measurements significantly degrades the performance of detection algorithms. In this paper, we focus on developing an adaptive filtering technique for the PD denoising problem. Heretofore, there are just a few literature reviews addressing the PD denoising based on such a method. The proposed recursive continuous S-shaped (RCSS) algorithm integrates the advantages of recursive strategy and continuous S-shaped function into adaptive noise cancellation (ANC) system, yielding enhanced filtering performance. The proposed algorithm can tackle PD noises in both Gaussian and impulsive scenarios, which is easy to implement in practical applications. The convergence behavior is also analyzed. Extensive simulation and experimental results confirm that the proposed algorithm can address polluted PD pulses, even in excessively noisy conditions, resulting in smaller mean square error (MSE) as compared to other state-of-the-art algorithms. [ABSTRACT FROM AUTHOR]

This paper presents a novel oscillation wave test system (OWTS) to detect the partial discharge (PD) of mounting defects in power cable insulation. In the proposed system, a charging capacitor is added to the circuit topology based on the traditional OWTS. The charging capacitor is charged to the desired voltage by a high-voltage DC power source. After the charging process, the test cable sample is charged by the capacitor. The resonant circuit is formed by the charging capacitor, the test cable, and the resonant reactor to create an oscillating decay voltage. With this novel method, no space charge is injected into the cable insulation. The effect of the charging capacitance on the charging efficiency is calculated with the Multisim software. This paper describes the working principle and the assembly of a laboratory prototype for the PD detection of a 500 m cable circuit. The test results show the feasibility of the novel OWTS method. [ABSTRACT FROM AUTHOR]

The onsite partial discharge (PD) detection of cable insulation is of great importance for power system maintenance. To preserve more basic features of denoised PD signal, in this paper, a PD denoising by a new class of affine projection algorithm (APA) is proposed based on the high-order error power (HOEP) criterion. We propose a new affine projection least mean absolute third algorithm (APLMATA), which exploits the HOEP criterion ($p=3$) and can achieve reliable performance under Gaussian interference. We further develop a modified APLMATA (MAPLMATA) to reduce the misadjustment with moderate computational burden. Analytical models are derived for MAPLMATA for Gaussian signals. To enhance the stability of the algorithm in generalized Gaussian noise scenarios, an affine project least mean $p$ th power algorithm (APLMPA) that includes the $p$ th power dependence on the error is presented. In particular, we apply the proposed APA-based algorithms to suppress the noise from PD signal in power cables. Simulation and experimental results demonstrate the effectiveness of the proposed algorithms for system identification and PD denoising. [ABSTRACT FROM AUTHOR]

Polyimide nano-composite film (Kapton 100CR) is a special type of engineering plastic film, which is widely used in turn insulation of form-wound inverter-fed motor. Partial discharge (PD) caused by high-frequency surge impulse is one of the key factors leading to premature failure of turn insulation of inverter-fed motors. Aging experiments on turn insulation samples under repetitive bipolar square impulse voltage were carried out in this study. Experimental results show that, in the presence of PD, the damage to the structure of the polyimide nano-composite film under impulse voltage is concentrated on the surface layer of the sample. Moreover, the results indicate that with the increase of aging time, the discharge phase distribution becomes broader. Therefore, the appearance of the discharge at higher phase would be the reflection that the insulation of the sample reaches its terminal stage. Surface microscopic images taken by the scanning electron microscope (SEM) show that, because of PD erosion, the polymer matrix was carbonized and volatilized, the residual nano-fillers remained on the surface and formed a screen layer to resist further damages caused by PDs. It is a symbol that faults expand rapidly when the floccules and voids appear on the surface layer, which indicates the insulation could be breakdown soon. [ABSTRACT FROM AUTHOR]

Locating the partial discharge (PD) source is one of the most effective means to locate local defects in power cable lines. The sampling rate and the frequency-dependent characteristic of phase velocity have an obvious influence on localization accuracy based on the times of arrival (TOA) evaluation algorithm. In this paper, we present a cross-correlation algorithm based on propagation distance to locate the PD source in cable lines. First, we introduce the basic principle of the cross-correlation function of propagation distance. Then we verify the proposed method through a computer simulation model and investigate the influences of propagation distance, sampling rate, and noise on localization accuracy. Finally, we perform PD location experiments on two 250 m 10 kV XLPE power cables using the oscillation wave test system. The simulation and experiment results indicate that compared with traditional TOA evaluation methods, the proposed method has superior locating precision. [ABSTRACT FROM AUTHOR]