Search

Recent use of very small photon beams (down to 4 mm) in stereotactic radiotherapy requires new detectors to accurately determine the delivered dose. Diamond detectors have been presented in the literature as an attractive candidate for this application, due to their small detection volume and the diamond atomic number (Z=6) which is close to water effective atomic number (Zeff∼7.42). However, diamond exhibits a density 3.51 times greater than that of water and recent studies using Monte Carlo simulations have demonstrated the drawback of a high-density detector on small beam output factors. The current study focuses on geometrical parameters of diamond detector, namely, the diamond dimensions and the electrode geometry, in order to solve the dosimetric issues still observed in small photon beams with diamond detectors. To give better insights to these open questions, we have used both computational method and experimental analysis. This study highlighted that reducing diamond dimensions is crucial for small beam output factor measurements and to limit the influence of its high density. Furthermore, electrodes covering the whole diamond surface were essential for a dose rate independence of the diamond detector. The optimal dosimeter derived from this work presented small diamond dimensions of approximately 1-1-0.15mm3, with diamond-like-carbon electrodes covering the whole diamond surface. A dose rate independence of this diamond detector (better than 0.5% over a wide range of dose rates available on a stereotactic dedicated facility) was obtained due to the electrode geometry. Concerning the output factor measurements, a good agreement (better than 1.1%) was observed between this carbon material detector and two types of passive dosimeters (LiF microcubes and EBT2 radiochromic films) for all beam sizes except the smallest field of 0.6-0.6 cm2 with a deviation of 2.6%. This new study showed the high performance of this diamond detector in small photon beams, in comparison with various commercially available passive and active dosimeters. [ABSTRACT FROM AUTHOR]

Purpose: In a previous work, output ratio (ORdet) measurements were performed for the 800 MU/min CyberKnife ® at the Oscar Lambret Center (COL, France) using several commercially available detectors as well as using two passive dosimeters (EBT2 radiochromic film and micro-LiF TLD-700). The primary aim of the present work was to determine by Monte Carlo calculations the output factor in water (OFMC,w) and the kQclin,Qmsrfclin,fmsr correction factors. The secondary aim was to study the detector response in small beams using Monte Carlo simulation. Methods: The LINAC head of the CyberKnife R ® was modeled using the PENELOPE Monte Carlo code system. The primary electron beam was modeled using a monoenergetic source with a radial gaussian distribution. The model was adjusted by comparisons between calculated and measured lateral profiles and tissue-phantom ratios obtained with the largest field. In addition, the PTW 60016 and 60017 diodes, PTW 60003 diamond, and micro-LiF were modeled. Output ratios with modeled detectors (ORMC,det) and OFMC,w were calculated and compared to measurements, in order to validate the model for smallest fields and to calculate kQclin,Qmsrfclin,fmsr correction factors, respectively. For the study of the influence of detector characteristics on their response in small beams; first, the impact of the atomic composition and the mass density of silicon, LiF, and diamond materials were investigated; second, the material, the volume averaging, and the coating effects of detecting material on the detector responses were estimated. Finally, the influence of the size of silicon chip on diode response was investigated. Results: Looking at measurement ratios (uncorrected output factors) compared to the OFMC,w, the PTW 60016, 60017 and Sun Nuclear EDGE diodes systematically over-responded (about +6% for the 5 mm field), whereas the PTW 31014 Pinpoint chamber systematically under-responded (about -12% for the 5 mm field). ORdet measured with the SFD diode and PTW 60003 diamond detectors were in good agreement with OFMC,w except for the 5 mm field size (about -7.5% for the diamond and +3% for the SFD). A good agreement with OFMC,w was obtained with the EBT2 film and micro- LiF dosimeters (deviation less than 1.4% for all fields investigated). kQclin,Qmsrfclin,fmsrcorrection factors for several detectors used in this work have been calculated. The impact of atomic composition on the dosimetric response of detectors was found to be insignificant, unlike the mass density and size of the detecting material. Conclusions: The results obtained with the passive dosimeters showed that they can be used for small beam OF measurements without correction factors. The study of detector response showed that ORdet is depending on the mass density, the volume averaging, and the coating effects of the detecting material. Each effect was quantified for the PTW 60016 and 60017 diodes, the micro- LiF, and the PTW 60003 diamond detectors. None of the active detectors used in this work can be recommended as a reference for small field dosimetry, but an improved diode detector with a smaller silicon chip coated with tissue-equivalent material is anticipated (by simulation) to be a reliable small field dosimetric detector in a nonequilibrium field. [ABSTRACT FROM AUTHOR]

Recent developments of new therapy techniques using small photon beams, such as stereotactic radiotherapy, require suitable detectors to determine the delivered dose with a high accuracy. The dosimeter has to be as close as possible to tissue equivalence and to exhibit a small detection volume compared to the size of the irradiation field, because of the lack of lateral electronic equilibrium in small beam. Characteristics of single crystal diamond (tissue equivalent material Z = 6, high density) make it an ideal candidate to fulfil most of small beam dosimetry requirements. A commercially available Element Six electronic grade synthetic diamond was used to develop a single crystal diamond dosimeter (SCDDo) with a small detection volume (0.165 mm3). Long term stability was studied by irradiating the SCDDo in a 60Co beam over 14 h. A good stability (deviation less than ± 0.1%) was observed. Repeatability, dose linearity, dose rate dependence and energy dependence were studied in a 10 × 10 cm2 beam produced by a Varian Clinac 2100 C linear accelerator. SCDDo lateral dose profile, depth dose curve and output factor (OF) measurements were performed for small photon beams with a micro multileaf collimator m3 (BrainLab) attached to the linac. This study is focused on the comparison of SCDDo measurements to those obtained with different commercially available active detectors: an unshielded silicon diode (PTW 60017), a shielded silicon diode (Sun Nuclear EDGE), a PinPoint ionization chamber (PTW 31014) and two natural diamond detectors (PTW 60003). SCDDo presents an excellent spatial resolution for dose profile measurements, due to its small detection volume. Low energy dependence (variation of 1.2% between 6 and 18 MV photon beam) and low dose rate dependence of the SCDDo (variation of 1% between 0.53 and 2.64 Gy min−1) are obtained, explaining the good agreement between the SCDDo and the efficient unshielded diode (PTW 60017) in depth dose curve measurements. For field sizes ranging from 0.6 × 0.6 to 10 × 10 cm2, OFs obtained with the SCDDo are between the OFs measured with the PinPoint ionization chamber and the Sun Nuclear EDGE diode that are known to respectively underestimate and overestimate OF values in small beam, due to the large detection volume of the chamber and the non-water equivalence of both detectors. [ABSTRACT FROM AUTHOR]

Abstract: The accurate determination of absorbed dose in small photon beams, especially for stereotactic radiation therapy, is a difficult task with commercially available detectors. As these small fields are characterized by high dose gradients, a lack of lateral particle equilibrium and a variation of energy spectra with beam sizes, a dosimeter with high resolution, tissue-equivalence and high precision is required. The new radiochromic film EBT2, which meets these criteria, was fully characterized in Institut de Radioprotection et Sûreté Nucléaire (IRSN) for this application. This type of film was tested with the reading system EPSON Dual Lens Perfection V700 flatbed scanner in transmission mode. Warm-up effects of the scanner were studied as well as the influence of the scanner light. Uniformity of unirradiated and irradiated EBT2 films in terms of pixel value was found to be respectively 0.3% (1 SD) and 0.5% (1 SD). An original, accurate and efficient radiochromic film dosimetry protocol was established. The overall uncertainty for dose measurement with EBT2 films using this protocol was estimated at less than 2% (1 SD). Encouraging measurements of output factors were performed on a Novalis system. [Copyright &y& Elsevier]

The purpose of this work is to assess the feasibility of performing dosimetry with the TruView (ModusQA, London, Ontario, Canada) MTB Fricke gel by MRI reading on a low field MR-Linac (0.35 T). Radiochromic TruView gels were manufactured at IRSN. A 4 echoes time (TE) single-shot fast spin echo sequence (HASTE) was used for 2D images acquisitions. Raw MRI images were denoised (MP-PCA) and transversal relaxation rates (R2) maps were extracted using a homemade Matlab routine. Temperature influences on R2 as well as gel homogeneity were investigated. A dosimetric evaluation of the TruView gel was conducted implying four gels made from the same batch, with three of them dedicated to calibration, and the fourth one received a simple dosimetric plan. Results showed the TruView gel to be sensitive to temperature drift. A protocol was thus developed to ensure thermal stability with the use of a dedicated temperature-controlled water bath. An inhomogeneity that manifests as a R2 increase near the air/gel interface was found to cause a 4% amplitude deviation in R2 along unirradiated gels. Air sealing drastically reduced the inhomogeneity. Dose versus R2 calibration was established. TruView gel sensitivity was found to be low (0.0093 Gy−1 s−1). 1D and 2D comparison to planned dose distribution displayed overall agreement with global gamma index (5%/3 mm) evaluation with an 87 % passing rate. Main discrepancies in the low and gradient dose regions were attributable to the calibration range and diffusion effects. This study demonstrated the feasibility of using the TruView gel for dosimetric evaluation on a low field MR-Linac. The protocol developed needs to be extended to a full 3D evaluation to enable patient QA and may require modifications to the gel formulation to increase its overall sensitivity and ensure limited dependence on temperature drift. • Dosimetry using the TruView Fricke gel, MRI reading on a low-field MR-Linac (0.35 T). • Use of fast MRI sequence (HASTE) for dosimetric evaluations. • Temperature drift and inhomogeneity in the gels, low R2-Dose sensitivity. • Stabilization protocol for the TruView gel to ensure reliable dosimetric evaluations. • TruView gel suitable for dosimetric evaluation, full 3D validation is needed. [ABSTRACT FROM AUTHOR]

Abstract: Recent developments of new therapy techniques using small photon beams, such as stereotactic radiotherapy, require new detectors to precisely determine the delivered dose. The dosimeter has to be as close as possible to tissue equivalence and exhibit a small detection volume compared to the size of the irradiation field, because of the lack of lateral electronic equilibrium in small beam. Characteristics of single crystal diamond (tissue equivalent material Z=6, high density) make it an ideal candidate to fulfill most of small beam dosimetry requirements. A commercially Element Six electronic grade synthetic diamond was selected to develop a single crystal diamond dosimeter (SCDDo) with a small detection volume (0.4mm3). The Monte-Carlo code PENELOPE (parallelized version) was used to optimize both geometry and packaging materials of the diamond detector in order to respect the tissue-equivalent requirement. SCDDo dose profile and output factor (OF) measurements, were performed for small photon beams with a micro multileaf collimator m3 (BrainLab) attached to a Varian Clinac 2100 C linear accelerator. These measurements were compared to different detectors, both active and passive: silicon diode (PTW 60017), EBT2 radiochromic films, PinPoint ionization chamber (PTW 31014). SCDDo presents an excellent spatial resolution for dose profile measurements, due its small detection volume. OFs obtained with SCDDo are very satisfactory from 0.6×0.6cm2 to 10×10cm2 field sizes, compared to PinPoint ionization chamber which underestimates OF values in small beam. [Copyright &y& Elsevier]