Search

The wearable application of flexible organic solar cells (f‐OSCs) necessitates high power conversion efficiency (PCE) and mechanical robustness. However, photoactive films based on efficient non‐fullerene small molecule acceptors (NF‐SMAs) are typically brittle, leading to poor mechanical stability in devices. In this study, we achieved a remarkable PCE of 18.06 % in f‐OSCs while maintaining ultrahigh mechanical robustness (with a crack‐onset strain (COS) of higher than 11 %) by incorporating a linker dimerized acceptor (DOY‐TVT). Compared to binary blends, ternary systems exhibit reduced non‐radiative recombination, suppressed crystallization and diffusion of NF‐SMAs, and improved load distribution across the chain networks, enabling the dissipation of the load energy. Thus, the ternary f‐OSCs developed in this study achieved, high PCE and stability, surpassing binary OSCs. Moreover, the developed f‐OSCs retained 97 % of the initial PCE even after 3000 bending cycles, indicating excellent mechanical stability (9.1 % higher than binary systems). Furthermore, the rigid device with inverted structure based on the optimal active layer exhibited a substantial increase in efficiency retention, with 89.6 % after 865 h at 85 °C and 93 % after more than 1300 h of shelf storage at 25 °C. These findings highlight the potential of the linker oligomer acceptor for realizing high‐performing f‐OSCs with ultrahigh mechanical robustness. [ABSTRACT FROM AUTHOR]

Substantial efforts of A–DA′D–A type non‐fullerene acceptors (NFAs) molecular design have impelled power conversion efficiency (PCE) of single junction organic solar cells (OSCs) to exceed 19%. Asymmetric geometry strategy, selenium‐substitution, and end‐group engineering are proven to be effective modification methods. Here, two novel selenium substitution asymmetric NFAs, AsymSSe‐2F, and AsymSSe‐2Cl, are synthesized to investigate the synergistic modification effects on device performance compared with symmetric Y6. When blending AsymSSe‐2F with the wide‐bandgap and high crystallinity polymer D18, a remarkable PCE of 18.31% is yielded, and an excellent fill factor of 79.46% is achieved, which is attributed to the broadened absorption, enhanced π–π stacking, balanced carrier mobilities, and fine phase‐separation morphology. Notably, among the reported selenium‐substituted asymmetric NFAs based OSCs, especially combined with the seldom‐reported D18, this PCE is top‐ranked in binary bulk heterojunction organic solar cells. This work indicates that the combined modification of asymmetric geometry and selenium substitution in NFAs is a promising strategy for fabricating high performance OSCs. [ABSTRACT FROM AUTHOR]

Despite the great progress of flexible perovskite solar cells (f‐PSCs), it still faces several challenges during the homogeneous fabrication of high‐quality perovskite thin films, and overcoming the insufficient exciton dissociation. To the ends, we rationally design the ferroelectric two‐dimensional (2D) perovskite based on pyridine heterocyclic ring as the organic interlayer. We uncover that incorporation of the ferroelectric 2D material into 3D perovskite induces an increased built‐in electric field (BEF), which enhances the exciton dissociation efficiency in the device. Moreover, the 2D seeds could assist the 3D crystallization by forming more homogeneous and highly‐oriented perovskite crystals. As a result, an impressive power conversion efficiency (PCE) over 23 % has been achieved by the f‐PSCs with outstanding ambient stability. Moreover, the piezo/ferroelectric 2D perovskite intrigues a decreased hole transport barriers at the ITO/perovskite interface under tensile stress, which opens new possibilities for developing highly‐efficient f‐PSCs. [ABSTRACT FROM AUTHOR]

Comprehensive Summary Inverted (p‐i‐n) perovskite solar cells (PSCs) are favored by researchers owing to their superior compatibility with flexible substrates and tandem device fabrication. Additionally, the hole transport layer (HTL) serves as a template for perovskite growth, which is critical for enhancing the device performance. However, the current research on how the HTL promotes perovskite crystallization is insufficient. Here, 4PADCB, a self‐assembled monolayer (SAM) hole transport material, was optimized as a superior template for perovskite growth through comparative analysis; accordingly, compact perovskite film with vertical growth was prepared. The better matched energy level alignment between 4PADCB and perovskite suppressed nonradiative recombination at the interface and enabled rapid hole extraction. Moreover, high‐quality perovskite film growth on 4PADCB exhibited lower Young's modulus and less residual stress. By integrating 4PADCB into p‐i‐n PSCs, the optimal device achieved a power conversion efficiency of 24.80%, with an open‐circuit voltage of 1.156 V, thus achieving the best rank among devices without perovskite post‐treatment, additives, dopants, or intermediate layers. Furthermore, the unencapsulated device demonstrated exceptional thermostability and photostability under maximum power point tracking. Thus, this work provides a new understanding for the development of novel SAMs and perovskite growth, and it is expected to further improve device performance. [ABSTRACT FROM AUTHOR]

[Display omitted] • Two non-fullerene donors with A-π-A'-π-A type structures designed and synthesised. • The structures contain 3-hexylrhodanine and 2-butyl cyanoacetate end groups. • The introduction of DB-1/2 achieved dual FRET in PM6:Y6 system for the first time. • The excessive self-aggregation of Y6 was broken in ternary solar cells. • The ternary organic solar cells achieve high J SC of 28.0 mA cm−2. Organic solar cells (OSCs) have aroused widespread concerns in green energy and wearable electronics. One of the most powerful way to achieve high efficient OSCs is maximizing fill factor (FF) and short-circuit current density (J SC). Herein, two A-π-A'-π-A type conjugated molecules bearing different electron-deficient end groups, DB-1 and DB-2, were designed and synthesized as donor-typed third components in the well-known PM6:Y6 host system. The photoluminescence and ultrafast transient absorption spectra clearly demonstrated that dual Förster resonance energy transfer (FRET) effects were well established for the first time in the PM6:Y6-based ternary OSCs. Furthermore, the introduction of DB-1 and DB-2 could effectively prevent the excessive self-aggregation of Y6, resulting in the optimal phase separations in the ternary films. Thus, the ternary OSCs based on PM6:DB-1:Y6 and PM6:DB-2:Y6 both achieved excellent J SC of ∼28.0 mA cm−2 and high FF ∼0.780, which are significantly higher than those of the binary devices. Consequently, rational molecular design and dual FRET effects provide a new and effective method to simultaneously improve the J SC and FF of OSCs. [ABSTRACT FROM AUTHOR]