Search

An investigation specifically focusing on the relationship among processing parameters, structure, and mechanical properties of solid two‐stage die‐drawn polypropylene (PP) has been done in this study, which aimed at providing a reliable reference in the choose of appropriate conditions that can be able to meet a specific processing requirement. PP sheets were drawn through a self‐design solid two‐stage die‐drawing apparatus to various drawing ratios (DRs) at different speeds and with different die‐exit thicknesses. The results showed that tensile strength, modulus, and the degree of orientation significantly increased with the nominal DR and could be further improved by increasing the drawing speed. While the crystallinity increased prior and decreased to near a constant value when the drawing speed was over 150 mm/min in the researched scope. Larger the die‐exit thickness was, lower the orientation degree was but higher the crystallinity could be obtained. Compared with crystallinity, orientation degree plays a leading role in the final product properties during a two‐stage solid die‐drawing process. POLYM. ENG. SCI., 59:2347–2355, 2019. © 2019 Society of Plastics Engineers [ABSTRACT FROM AUTHOR]

ABSTRACT: High oriented isotactic polypropylene prepared by self‐designed two‐stage die drawing apparatus was explored through kinds of methods, including differential scanning calorimetry, two‐dimensional wide‐angle X‐ray diffraction, polarized light microscope, and tensile test. The results showed that there was a great difference between the orientation mechanism and structure evolution of two‐stage solid die drawing process and single‐stage solid die drawing process. All samples would undergo free drawing process after die drawing process. Die drawing and free drawing process were of equal importance to single‐stage die drawing process while die drawing process showed an prominent contribution to the two‐stage die drawing process. Drawing speed showed beneficial influence on die drawing process for both single‐ and two‐stage die drawing process routes. Under the same processing condition, tensile strength and modulus of samples prepared by two‐stage die drawing process were higher than those prepared by single‐stage die drawing process and the maximum value could reach 241.93 MPa and 3.57 GPa, respectively. Moreover, two‐stage die drawing samples showed better dimensional stability than single‐stage die drawing samples especially under low draw rate. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 46581. [ABSTRACT FROM AUTHOR]

Long chain branching polypropylene (LCBPP) has good application prospect but the synergistic effects of the long chain branching (LCB) structure and complex flow field on the crystallization behavior of LCB polymers are still elusive. In the present work, microparts of isotactic polypropylene (iPP)/LCBPP blends were prepared by microinjection molding (MIM). The effect of the LCB structure on the morphology evolution and the β-crystal distribution in microparts were investigated. Interestingly, adding LCBPP facilitates the formation of oriented β-crystals along the shear direction in the core layer of the microparts but unexpectedly, decreases the relative content of β-crystals due to the heterogeneous nucleation effect of LCBPP. Moreover, the introduction of LCBPP can also improve the orientation degree of the molecular chains and shrink the thickness of the core layer thereby inevitably suppressing the 'skin-core' structure which might optimize the properties of MIM parts. [ABSTRACT FROM AUTHOR]

Oriented structure, mainly controlled by processing conditions, is another efficient method of reinforcing polymer materials in addition to compounding with rigid inorganic fillers such as carbon nanotubes (CNTs). The mechanical properties of oriented polypropylene (PP)/multiwalled CNT (MWCNT) composites, which are vital to their application fields, are investigated extensively in this paper, with an aim to distinguish the contribution of MWCNTs contents from that of the oriented structure to the final performance of the composite. The results indicate that MWCNTs mainly increase the modulus of the composites by approximately 140%. The oriented structure formed during the die-drawing process contributes more to the enhancement of tensile strength, increasing up to 550%. The modulus and tensile strength can be further improved by increasing the drawing speed. Moreover, the tensile stress field in the die-drawing process can vastly improve the dispersion of the MWCNTs in the matrix, thus providing a new idea for improving the dispersion of nanofillers in the polymer matrix. • Die-drawing process contributes more to increase tensile strength. • MWCNTs mainly increase modulus rather than tensile strength. • Tensile strength and modulus can be further improved by increasing the drawing rate. • The die-drawing process can vastly improve the dispersion of MWCNTs in the PP matrix. • MWCNTs can hinder the molecular chain orientation. [ABSTRACT FROM AUTHOR]