Search

Wood is extensively used as a construction material. Despite increasing knowledge of its mechanical properties, the contribution of the cell-wall matrix polymers to wood mechanics is still not well understood. Previous studies have shown that axial stiffness correlates with lignin content only for cellulose microfibril angles larger than around 20°, while no influence is found for smaller angles. Here, by analysing the wood of poplar with reduced lignin content due to down-regulation of CAFFEOYL SHIKIMATE ESTERASE, we show that lignin content also influences axial stiffness at smaller angles. Micro-tensile tests of the xylem revealed that axial stiffness was strongly reduced in the low-lignin transgenic lines. Strikingly, microfibril angles were around 15° for both wild-type and transgenic poplars, suggesting that cellulose orientation is not responsible for the observed changes in mechanical behavior. Multiple linear regression analysis showed that the decrease in stiffness was almost completely related to the variation in both density and lignin content. We suggest that the influence of lignin content on axial stiffness may gradually increase as a function of the microfibril angle. Our results may help in building up comprehensive models of the cell wall that can unravel the individual roles of the matrix polymers., (© The Author(s) 2019. Published by Oxford University Press on behalf of the Society for Experimental Biology.)

Caffeoyl shikimate esterase (CSE) was recently shown to play an essential role in lignin biosynthesis in Arabidopsis ( Arabidopsis thaliana ) and later in Medicago truncatula However, the general function of this enzyme was recently questioned by the apparent lack of CSE activity in lignifying tissues of different plant species. Here, we show that down-regulation of CSE in hybrid poplar ( Populus tremula × Populus alba ) resulted in up to 25% reduced lignin deposition, increased levels of p -hydroxyphenyl units in the lignin polymer, and a relatively higher cellulose content. The transgenic trees were morphologically indistinguishable from the wild type. Ultra-high-performance liquid chromatography-mass spectrometry-based phenolic profiling revealed a reduced abundance of several oligolignols containing guaiacyl and syringyl units and their corresponding hydroxycinnamaldehyde units, in agreement with the reduced flux toward coniferyl and sinapyl alcohol. These trees accumulated the CSE substrate caffeoyl shikimate along with other compounds belonging to the metabolic classes of benzenoids and hydroxycinnamates. Furthermore, the reduced lignin amount combined with the relative increase in cellulose content in the CSE down-regulated lines resulted in up to 62% more glucose released per plant upon limited saccharification when no pretreatment was applied and by up to 86% and 91% when acid and alkaline pretreatments were used. Our results show that CSE is not only important for the lignification process in poplar but is also a promising target for the development of improved lignocellulosic biomass crops for sugar platform biorefineries., (© 2017 American Society of Plant Biologists. All Rights Reserved.)

Lignin engineering is a promising tool to reduce the energy input and the need of chemical pre-treatments for the efficient conversion of plant biomass into fermentable sugars for downstream applications. At the same time, lignin engineering can offer new insight into the structure-function relationships of plant cell walls by combined mechanical, structural and chemical analyses. Here, this comprehensive approach was applied to poplar trees (Populus tremula × Populus alba) downregulated for CINNAMYL ALCOHOL DEHYDROGENASE (CAD) in order to gain insight into the impact of lignin reduction on mechanical properties. The downregulation of CAD resulted in a significant decrease in both elastic modulus and yield stress. As wood density and cellulose microfibril angle (MFA) did not show any significant differences between the wild type and the transgenic lines, these structural features could be excluded as influencing factors. Fourier transform infrared spectroscopy (FTIR) and Raman imaging were performed to elucidate changes in the chemical composition directly on the mechanically tested tissue sections. Lignin content was identified as a mechanically relevant factor, as a correlation with a coefficient of determination (r²) of 0.65 between lignin absorbance (as an indicator of lignin content) and tensile stiffness was found. A comparison of the present results with those of previous investigations shows that the mechanical impact of lignin alteration under tensile stress depends on certain structural conditions, such as a high cellulose MFA, which emphasizes the complex relationship between the chemistry and mechanical properties in plant cell walls., (© 2017 The Authors The Plant Journal © 2017 John Wiley & Sons Ltd.)

The global demand for food, feed, energy and water poses extraordinary challenges for future generations. It is evident that robust platforms for the exploration of renewable resources are necessary to overcome these challenges. Within the multinational framework MultiBioPro we are developing biorefinery pipelines to maximize the use of plant biomass. More specifically, we use poplar and tobacco tree (Nicotiana glauca) as target crop species for improving saccharification, isoprenoid, long chain hydrocarbon contents, fiber quality, and suberin and lignin contents. The methods used to obtain these outputs include GC-MS, LC-MS and RNA sequencing platforms. The metabolite pipelines are well established tools to generate these types of data, but also have the limitations in that only well characterized metabolites can be used. The deep sequencing will allow us to include all transcripts present during the developmental stages of the tobacco tree leaf, but has to be mapped back to the sequence of Nicotiana tabacum. With these set-ups, we aim at a basic understanding for underlying processes and at establishing an industrial framework to exploit the outcomes. In a more long term perspective, we believe that data generated here will provide means for a sustainable biorefinery process using poplar and tobacco tree as raw material. To date the basal level of metabolites in the samples have been analyzed and the protocols utilized are provided in this article.

Next-generation (NG) sequencing in a natural population of Populus nigra revealed a mutant with a premature stop codon in the gene encoding hydroxycinnamoyl-CoA : shikimate hydroxycinnamoyl transferase1 (HCT1), an essential enzyme in lignin biosynthesis. The lignin composition of P. nigra trees homozygous for the defective allele was compared with that of heterozygous trees and trees without the defective allele. The lignin was characterized by phenolic profiling, lignin oligomer sequencing, thioacidolysis and NMR. In addition, HCT1 was heterologously expressed for activity assays and crosses were made to introduce the mutation in different genetic backgrounds. HCT1 converts p-coumaroyl-CoA into p-coumaroyl shikimate. The mutant allele, PnHCT1-Δ73, encodes a truncated protein, and trees homozygous for this recessive allele have a modified lignin composition characterized by a 17-fold increase in p-hydroxyphenyl units. Using the lignin pathway as proof of concept, we illustrated that the capture of rare defective alleles is a straightforward approach to initiate reverse genetics and accelerate tree breeding. The proposed breeding strategy, called 'breeding with rare defective alleles' (BRDA), should be widely applicable, independent of the target gene or the species., (© 2013 The Authors. New Phytologist © 2013 New Phytologist Trust.)