Search

The inverter is considered the core of the PV power plant. The inverter's failure leads to generation loss and decreases plant availability. So, it is required to investigate a clear Root Cause Analysis (RCA) to deduce the failure causes and implement the required corrective action in addition to the preventive action to avoid more inverter failure, hereby maintaining the plant available to a certain value. This paper discusses real-time mode operation data analysis of the PV grid-connected inverter due to real central inverter incidents in Benban solar park located in Egypt.The central inverter plays an important role in the Mega-Scale PV power plant. The main function of this inverter is to convert the DC power produced by the PV modules to AC power to be injected into the utility grid by considering specific characteristics based on the grid code. The availability of any PV power plant directly depends on the healthy inverter's operation. The more increases for the installed inverters, the less availability loss in the case of inverter partial or catastrophic failures. So, it is required to focus on the failure causes of the central inverter by implementing a technical analysis using the available operational data. The monitored data of the central inverter in the PV power plant is classified into two types. The first type is the continuous time data stored in the memory. It represents the waveforms of inverter outputs like voltage, current, frequency, .... etc. Unfortunately, in case of a catastrophic failure, the central inverter is completely charred, and the continuous time data is lost due to storage memory damage. The second type is the operation data that is recorded by the SCADA system (per one-minute interval). Hereby, the operation data is the sole data in the case of the completely charred inverter. The representation of the operational data in curves indicates symptoms that can be used for the RCA processes. The investigation outcomes include three results. The first result is detecting the signature of the IGBT thermal stress on the voltage balance of the DC link capacitor. The second result is verifying a scenario for the cause of the IGBT failure by implementing a technical mathematical model based on the detected symptoms that denote the fault signature which is considered the thread-tip for detecting the failure cause. The third result is the simulating scenario for the interpretation of a DC link capacitors explosion due to the short circuit fault that occurred due to IGBT failure. The investigation in this paper is performed based on operation data analysis of the PV grid-connected inverter (central type) due to a real incident. The analysis methodology is based on mathematical calculation for the IGBT junction temperature using the measured heatsink temperature. The study concludes that after the IGBT failure occurred, it was a short circuit for a while and closed the terminals of the DC link capacitors. So, the DC link capacitors exploded and produced heavy sparks that led to enough fire to burn the inverter container completely. [ABSTRACT FROM AUTHOR]

Summary: This paper proposes three‐phase microinverter able to process the power of three PV modules simultaneously and independently; thus, efficient utilization of PV modules through distributed maximum power point tracking (DMPPT) is realized. The proposed microinverter employs switched capacitors (SCs) networks combined with three‐phase voltage source inverter; it is named switched capacitor buck‐boost voltage source inverter and abbreviated as SC‐BBVSI. The connections of SCs networks are determined to fulfill the high boosting gain along with minimized leakage currents. In addition, low capacitances values can be employed for power decoupling purpose. Thus, in addition to DMPPT feature, three features of high boosting gain, high‐reliable product, and minimized leakage current are realized without using the bulky and costly isolation transformer. In this paper, the operation modes of SC‐BBVSI for single and multi‐input scenarios are explained. The modulation strategy to realize these modes along with the control system design is presented as well. The relations required to design the passive elements and identify the device's stresses are derived. The features of the proposed microinverter are confirmed through detailed comparison with other recently reported topologies. Both simulation and experimental results are provided to verify the features of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper proposes a new three-phase modular multilevel inverter (MMLI). The proposed inverter consists of repeated modular primary cells that are connected in series configuration. Therefore, the proposed topology can be extended to get more output voltage levels by adding additional cells without increasing voltage stresses across power switches. Both sinusoidal pulsewidth modulation (SPWM) and staircase modulation are successfully applied to the proposed inverter. The proposed inverter features many advantages such as reduced number of semiconductor power switches, driver circuits, dc-voltage sources, simplified control algorithm, and reduced voltage stresses across the switches independent of output voltage level. Furthermore, the performance of the proposed inverter is studied under both open-loop and closed-loop operations for highly inductive load. Beside the obtained simulation results, a laboratory prototype has been carried out and tested to verify the control techniques and performances of the topology. Simulation and experimental results are compared together to highlight the similarity and consistence of them. [ABSTRACT FROM AUTHOR]

Maximum Power Point Tracking (MPPT) control is an essential part of every photovoltaic (PV) system, in order to overcome any change in ambient environmental conditions and ensure operation at maximum power.. Recently, micro-inverters have gained a lot of attention due to their ability to track the true MPP for each individual PV module, which is considered a powerful solution to overcome the partial shading and power mismatch problems which exist in series-connected panels. Although the LLC resonant converter has high efficiency and high boosting ability, traditional MPPT techniques based on Pulse Width Modulation (PWM) do not work well with it. In this paper, a fixed frequency predictive MPPT technique is presented for the LLC resonant converter to be used as the first-stage in a PV micro-inverter. Using predictive control enhances the tracking efficiency and reduces the steady state oscillation. Operation with fixed switching frequency for the LLC resonant converter improves the total harmonic distortion profile of the system and ease the selection of circuit magnetic component. To demonstrate the effectiveness of the proposed MPPT technique, the system is simulated using MATLAB/Simulink platform. Furthermore, a 150 W hardware prototype is developed and tested. Both simulation and experimental results are consistent and validate the proper operation of the developed system. [ABSTRACT FROM AUTHOR]