Search

The quasi-continuous exhaust (QCE) regime is a regime that is naturally type-I ELM-free. It combines the high density at the plasma edge needed for power exhaust with the high normalised energy confinement typical for H-mode operation. In the QCE regime large-scale ELMs are avoided and high-frequency, low-amplitude filaments are present leading to the name-giving quasi-continuous edge transport of particles and energy. This contribution reports that for the first time the QCE regime was successfully achieved in JET with a metal wall. Moreover, it was demonstrated in the recent JET deuterium-tritium campaign DTE3 that the regime is compatible with D–T operation. Porting the QCE regime to JET strongly benefited from the experimental and modelling efforts at the medium sized tokamaks ASDEX Upgrade and TCV. Using the physics picture developed from the ASDEX Upgrade experimental results, the route to the QCE regime in JET reported here is following closely the approach that was successful in ASDEX Upgrade. First, strong plasma shaping—large elongation and triangularity and the highly correlated closeness to double null—is developed. Second, sufficient fuelling to achieve high enough density at the pedestal foot, close to the separatrix, is applied. In addition, neon seeding proved to be very beneficial to avoid type-I ELMs when reducing the main ion fuelling.

Precise values for radiated energy in tokamak disruption experiments are needed to validate disruption mitigation techniques for burning plasma tokamaks like ITER and SPARC. Control room analysis of radiated power ( P _rad ) on JET assumes axisymmetry, since fitting 3D radiation structures with limited bolometry coverage is an under-determined problem. In mitigated disruptions, radiation is toroidally asymmetric and 3D, due to fast-growing 3D MHD modes and localized impurity sources. To address this problem, Emis3D adopts a physics motivated forward modeling (‘guess and check’) approach, comparing experimental bolometry data to synthetic data from user-defined radiation structures. Synthetic structures are observed with the Cherab modeling framework and a best fit chosen using a reduced χ ^2 statistic. 2D tomographic inversion models are tested, as well as helical flux tubes and 3D MHD simulated structures from JOREK. Two nominally identical pure neon shattered pellet injection (SPI) mitigated discharges in JET are analyzed. 2D tomographic inversions with added toroidal freedom are the best fits in the thermal quench (TQ) and current quench (CQ). In the pre-TQ, 2D reconstructions are statistically the best fits, but are likely over-optimized and do not capture the 3D radiation structure seen in fast camera images. The next-best pre-TQ fits are helical structures that extend towards the high-field side, consistent with an impurity flow under the magnetic nozzle effect also observed in JOREK simulations. Whole-disruption radiated fractions of $ 0.98 +0.03/ $ $ -0.29 $ and $ 1.01 +0.02/-0.17 $ are found, suggesting that the stored energy may have been fully mitigated by each SPI, although mitigation efficiencies well below ITER and SPARC requirements for high energy pulses are still within the large uncertainties. Emis3D is also used to validate JOREK SPI simulations, and confirms improvements in matching experiment from changes to impurity modeling. Time-dependent toroidal peaking factors are calculated and discussed.

The pre-thermal quench (pre-TQ) dynamics of a pure deuterium ( $\mathrm{D}_2$ ) shattered pellet injection (SPI) into a $3\,\mathrm{MA}$ / $7\,\mathrm{MJ}$ JET H-mode plasma is studied via 3D non-linear MHD modelling with the JOREK code. The interpretative modelling captures the overall evolution of the measured density and radiated power. The simulations also identify the importance of the drifts of ablation plasmoids towards the tokamak low field side (LFS) and the impurities in the background plasma in fragment penetration, assimilation, radiative cooling and MHD activity in $\mathrm{D}_2$ SPI experiments. It is found that plasmoid drifts lead to an about 70% reduction of the central line-integrated density (compared to a simulation without drifts) in the JET $\mathrm{D}_2$ SPI discharge considered. Impurities that pre-exist before the SPI as well as those from possible impurity influxes related to the SPI are shown to dominate the radiation in the considered discharge. With inputs from JOREK simulations, modelling with the Lagrangian particle-based pellet code PELOTON reproduces the deviation of the SPI fragments in the direction of the major radius as observed by the fast camera. This confirms the role of rocket effects and plasmoid drifts in the considered discharge and reinforces the validity of the JOREK modelling. The limited core density rise due to plasmoid drifts and the strong radiative cooling and MHD activity with impurities (depending on their species and concentration) could limit the effectiveness of LFS $\mathrm{D}_2$ SPI in runaway electron avoidance and are worth considering in the design of the ITER disruption mitigation system.

The JET-ILW pure tritium and deuterium–tritium (DTE2) experimental campaigns took place in 2021–2022. Tritium (T) and deuterium–tritium (D–T) operations present challenges not encountered in present day tokamaks (Horton et al 2016 Fusion Eng. Des. 109–111 925–36). This contribution focuses on ion cyclotron resonance heating (ICRH) operations in tritium and deuterium–tritium plasmas, starting with a summary of the program of improvements to the ICRH system which spanned a few years prior to these experiments. Procedures were implemented to address specific constraints from tritium and deuterium–tritium operations (tritium safety and reduced access to the RF generator area) and increase the system reliability and power availability during plasma pulses. Operation of the upgraded real time RF power control system that maximises the launched power while taking into account limitations from the system or antenna coupling is described. We also report on the result from dedicated pulses performed to assess the potential harmful impact of the 2nd harmonic tritium resonance in the plasma, close to the inner wall, when using the standard central hydrogen minority ICRH scheme. During DTE2, the ITER-like antenna was not used because water leaked from an in-vessel capacitor into the vessel on day-2 of the experimental campaign. The lessons learnt from this incident are highlighted. Finally, the ICRH plant adjustments required to safely perform ion cyclotron wall cleaning discharges are described.

A baseline scenario of deuterium–tritium (D–T) plasma with peripheral high-field-side fuelling pellets has been produced in JET in order to mimic the situation in ITER. The isotope mix ratio is controlled in order to target the value of 50%–50% by a combination of tritium gas puffing and deuterium pellet injection. Multiple factors controlling the fuelling efficiency of individual pellets are analysed, with the following findings: (1) prompt particle losses due to pellet-triggered edge-localised modes (ELMs) are detected, (2) the plasmoid drift velocity might be smaller than that predicted by simulation, (3) post-pellet particle loss is controlled by transient phases with ELMs.The overall pellet particle flux normalised to the heat flux is similar to that in previous pellet fuelling experiments in AUG and JET.

The paper reports the first demonstration of in situ laser-induced desorption — quadrupole mass spectrometry (LID-QMS) application on a large scale fusion device performed in summer 2023. LID-QMS allows direct measurements of the fuel inventory of plasma facing components without retrieving them from the fusion device. The diagnostic desorbs the retained gases by heating a 3 mm diameter spot on the wall using a 1 ms long laser pulse and detects them by QMS. Thus, it can measure the gas content at any wall position accessible to the laser. The successful LID-QMS application in laboratory scale and on medium size fusion devices has now been demonstrated on the larger scale and it is already foreseen as tritium monitor diagnostic in ITER. This in situ diagnostic gives direct access to retention physics on a short timescale instead of campaign-integrated measurements and can assess the space-resolvedefficacy of detritation methods. LID-QMS can be applied on many materials: on Be deposits like in JET, B deposits like in TEXTOR, C based materials or on bulk-W.

A new H-mode regime at low density and low edge safety factor ( q _95 = 3.2, with $I_\mathrm{p}$ = 3 MA) that combines high energy confinement, stationary conditions for density and radiation and small Edge Localized Modes (ELMs) have been found in JET with Be/W wall. Such a regime is achieved by operating without external gas puffing, leading to a decrease in the edge density and a substantial increase in rotation and ion temperature in both the pedestal and the core region. Transport modelling shows a reduction of the turbulence, which starts in the pedestal region and extends into the plasma core, and outward impurity convection, consistent with the improved energy confinement and the lack of W accumulation observed in those conditions. In addition, large type I ELMs, typically found in gas-fuelled plasmas, are replaced by smaller and more frequent ELMs, whose appearance is correlated with a substantial reduction of the pedestal density and its gradient. Pedestals in this operating regime are stable to peeling–ballooning modes, consistent with the lack of large ELMs. This is in contrast to results in unfuelled JET-C plasmas that typically operated at higher pedestal densities and developed low frequency, large type I ELMs, thus pointing to the low density as one of the critical parameters for accessing this small ELMs regime in JET. This small ELMs regime exhibits the same low pedestal collisionality ( $\nu_{\mathrm{e},\mathrm{ped}}^*\sim0.1$ ) expected in ITER and operates at low q _95 , thus making it different from other small ELMs regimes that are typically obtained at higher q _95 and higher pedestal collisionality. These features make this newly developed H-mode regime in JET with Be/W wall a valuable tool for exploring the underlying transport, the different mechanisms of turbulence stabilization, as well as the physics associated with the appearance of small ELMs in high-temperature plasmas at ITER relevant pedestal collisionality.

The Joint European Torus (JET) fusion reactor was upgraded to the metallic wall configuration in 2011 which consisted of bulk beryllium (Be) tiles in the main chamber and bulk tungsten (W) and W-coated CFC tiles in the divertor (Matthews G.F. et al 2011 Phys. Scr. T148 014001). During each campaign, a series of wall damages were observed; on the upper dump plates (UDP) positioned to the top part of the vessel walls and on the inner wall—mainly affecting the inner wall guard limiters (IWGL). In both cases, it was concluded that the causes of these damages were unmitigated plasma disruptions. In the case of JET with the metallic wall configuration, most of these plasma disruptions were intentionally provoked. The overall objective was to study the behaviour of these phenomena, in order to assess their impact on the wall, improve understanding of morphological material changes, and—based on that—to develop, implement and test mitigation techniques for their prospective use on ITER. The current results bring additional information on the effects of the unmitigated plasma disruptions on the UDPs and are a significant extension of work presented in (Jepu et al 2019 Nucl. Fusion 59 086009) where the scale of the damage after three operational campaigns on the Be top limiters of JET was highlighted. In addition, new data is presented on the damaging effect that the high energetic runaway electrons had on the Be IWGL in JET.

The publication provide further insights into the dynamics of JET runaway electron (RE) beams mitigated by D2-rich shattered pellet injection (SPI) (Reux et al 2022 Plasma Phys. Control. Fusion 64 034002). Multi-diagnostic analyses show that mechanisms causing continuous RE losses and energy transfer from hot electrons to cold background plasma can act before the SPI. After the SPI, measurements are compatible with a reduction of the maximum energy and pitch angle of the RE distribution while the population of supra-thermal electrons increases. The RE population growth is likely due to electron avalanche. Dark island-like pattern chains, characterised by an integer poloidal mode number and a certain minor radius, are identified in the JET RE beam synchrotron radiation videos. The synchrotron island dynamics is studied via a newly developed computer vision code (Sommariva and Silburn https://c4science.ch/source/pSpiPTV/ ). The radial motion of synchrotron island chains is found to be consistent with the most plausible time evolution of the radial current density profile compatible with both the RE synchrotron videos and the total RE current time trace. Similarly, correlations are identified between the temporal progression of the synchrotron islands poloidal rotation frequency and sudden MHD relaxation events. Loss-of-RE events probably caused by non-linear interactions between synchrotron islands are observed for the first time. Experimental evidences suggest that synchrotron islands are possibly related to the existence of magnetic islands which may lead to the development of new RE beam mitigation strategies.

For its initial operational phase, ITER has until recently considered using non-nuclear hydrogen (H) or helium (He) plasmas to keep nuclear activation at low levels. To this end, the Tokamak Exploitation Task Force of the EUROfusion Consortium carried out dedicated experimental campaigns in He on the ASDEX Upgrade (AUG) and JET tokamaks in 2022, with particular emphasis put on the ELMy H-mode operation and plasma-wall interaction processes as well as comparison to H or deuterium (D) plasmas. Both in pure He and mixed He + H plasmas, H-mode operation could be reached but more effort was needed to obtain a stable plasma scenario than in H or D. Even if the power threshold for the LH transition was lower in He, entering the type-I ELMy regime appeared to require equally much or even more heating power than in H. Suppression of ELMs by resonant magnetic perturbations was studied on AUG but was only possible in plasmas with a He content below 19%; the reason for this unexpected behaviour remains still unclear and various theoretical approaches are being pursued to properly understand the physics behind ELM suppression. The erosion rates of tungsten (W) plasma-facing components were an order of magnitude larger than what has been reported in hydrogenic plasmas, which can be attributed to the prominent role of He ^2+ ions in the plasma. For the first time, the formation of nanoscale structures (W fuzz) was unambiguously demonstrated in H-mode He plasmas on AUG. However, no direct evidence of fuzz creation on JET was obtained despite the main conditions for its occurrence being met. The reason could be a delicate balance between W erosion by ELMs, competition between the growth and annealing of the fuzz, and coverage of the surface with co-deposits.

JET, the world’s largest operating tokamak with unique Be/W wall and tritium handling capability, completed a Deuterium-Tritium (D-T) campaign in 2021 (Maggi et al 29th Fusion Energy Conf. ) following a decade of preparatory experiments, dedicated enhancements, technical rehearsals and training (Horton et al 2016 Fusion Eng. Des. 109–111 925). Operation with tritium raises significant technical, safety and scientific challenges not encountered in standard protium or deuterium operation. This contribution describes the tritium operational requirements, pulses and technical preparations, new operating procedures, lessons learned and details on the achieved operational availability and performance. The preparation and execution of the recent JET tritium experiments benefitted from the previous experience in 1991 (Preliminary Tritium Experiment), 1997 (DTE1 campaign) and 2003 (Trace Tritium Campaigns) and consisted of the following five phases: technical rehearsals and scenario preparation, tritium commissioning, 100% tritium campaign, D-T campaign (DTE2), tritium clean-up. Following the clean-up JET resumed normal operation and is currently undertaking a further D-T campaign (DTE3).

This paper reports the first experiment carried out in deuterium–tritium addressing the integration of a radiative divertor for heat-load control with good confinement. Neon seeding was carried out for the first time in a D–T plasma as part of the second D–T campaign of JET with its Be/W wall environment. The technical difficulties linked to the re-ionisation heat load are reported in T and D–T. This paper compares the impact of neon seeding on D–T plasmas and their D counterpart on the divertor detachment, localisation of the radiation, scrape-off profiles, pedestal structure, edge localised modes and global confinement.

The JET hybrid scenario has been developed from low plasma current carbon wall discharges to the record-breaking Deuterium-Tritium plasmas obtained in 2021 with the ITER-like Be/W wall. The development started in pure Deuterium with refinement of the plasma current, and toroidal magnetic field choices and succeeded in solving the heat load challenges arising from 37 MW of injected power in the ITER like wall environment, keeping the radiation in the edge and core controlled, avoiding MHD instabilities and reaching high neutron rates. The Deuterium hybrid plasmas have been re-run in Tritium and methods have been found to keep the radiation controlled but not at high fusion performance probably due to time constraints. For the first time this scenario has been run in Deuterium-Tritium (50:50). These plasmas were re-optimised to have a radiation-stable H-mode entry phase, good impurity control through edge T _i gradient screening and optimised performance with fusion power exceeding 10 MW for longer than three alpha particle slow down times, 8.3 MW averaged over 5 s and fusion energy of 45.8 MJ.

The reference ion cyclotron resonance frequency (ICRF) heating schemes for ITER deuterium–tritium (D-T) plasmas at the full magnetic field of 5.3 T are second harmonic heating of T and ^3 He minority heating. The wave-particle resonance location for these schemes coincide and are central at a wave frequency of 53 MHz at 5.3 T. Experiments have been carried out in the second major D-T campaign (DTE2) at JET, and in its prior D campaigns, to integrate these ICRF scenarios in JET high-performance plasmas and to compare their performance with the commonly used hydrogen (H) minority heating. In 50:50 D:T plasmas, up to 35% and 5% larger fusion power and diamagnetic energy content, respectively, were obtained with second harmonic heating of T as compared to H minority heating at comparable total input powers and gas injection rates. The core ion temperature was up to 30% and 20% higher with second harmonic T and ^3 He minority heating, respectively, with respect to H minority heating. These are favourable results for the use of these scenarios in ITER and future fusion reactors. According to modelling, adding ICRF heating to neutral beam injection using D and T beams resulted in a 10%–20% increase of on-axis bulk ion heating in the D-T plasmas due to its localisation in the plasma core. Central power deposition was confirmed with the break-in-slope and fast Fourier transform analysis of ion and electron temperature in response to ICRF modulation. The tail temperature of fast ICRF-accelerated tritons, their enhancement of the fusion yield and time behaviour as measured by an upgraded magnetic proton recoil spectrometer and neutral particle analyser were found in agreement with theoretical predictions. No losses of ICRF-accelerated ions were observed by fast ion detectors, which was as expected given the high plasma density of n _e ≈ 7–8 × 10 ^19 m ^−3 in the main heating phase that limited the formation of ICRF-accelerated fast ion tails. ^3 He was introduced in the machine by ^3 He gas injection, and the ^3 He concentration was measured by a high-resolution optical penning gauge in the sub-divertor region. The DTE2 experiments with ^3 He minority heating were carried with a low ^3 He concentration in the range of 2%–4% given the fact that the highest neutron rates with ^3 He minority heating in D plasmas were obtained at low ^3 He concentrations of ∼2%, which also coincided with the highest plasma diamagnetic energy content. In addition to ^3 He introduced by ^3 He gas injection, an intrinsic concentration of ^3 He of the order of 0.2%–0.4% was measured in D-T plasmas before ^3 He was introduced in the device, which is attributed to the radioactive decay of tritium to ^3 He. According to modelling, even such low intrinsic concentrations of ^3 He lead to significant changes in ICRF power partitioning during second harmonic heating of T due to absorption of up to 30% of the wave power by ^3 He.

After the second Deuterium–Tritium Campaign (DTE2) in the JET tokamak with the ITER-Like Wall (ILW) and full tritium campaigns that preceded and followed after the DTE2, a sequence of fuel recovery methods was applied to promote tritium removal from wall components. The sequence started with several days of baking of the main chamber walls at 240 °C and at 320 °C. Subsequently, baking was superimposed with Ion-Cyclotron Wall Conditioning (ICWC) and Glow Discharge Conditioning (GDC) cleaning cycles in deuterium. Diverted plasma operation in deuterium with different strike point configurations, including a Raised Inner Strike Point (RISP) configuration, and with different plasma heating—Ion Cyclotron Resonance Frequency (ICRF) and Neutral Beam Injection (NBI)—concluded the cleaning sequence. Tritium content in plasma and in the pumped gas was monitored throughout the experiment. The applied fuel recovery methods allowed reducing the residual tritium content in deuterium NBI-heated plasmas to about 0.1% as deduced from neutron rate measurements. This value is well below the requirement of 1% set by the maximum 14 MeV fusion neutron budget allocated in the ensuing deuterium plasma campaign. The quantified tritium removal over the course of the experiment was $\left( {13.4 \pm 0.7} \right) \times {10^{22}}$ atoms or $\left( {0.67 \pm 0.03} \right)$ g with ∼58% attributed to baking, ∼12.5% to ICWC, ∼26% to GDC, and ∼3.5% to first low power RISP plasmas. The experimentally estimated amount of removed tritium is in good agreement with long-term tritium accounting by the JET tritium reprocessing plant, in which the unaccounted amount was reduced by $0.71$ g after the cleaning experiment.