Search

The results of experiments on the study of the generation of high-power pulsed soft X-ray (SXR) emission with a photon energy higher than 100 eV (in the spectral range with wavelengths λ shorter than 120 Å) during the plasma implosion of nested arrays of mixed composition with different ratios of array radii carried out on a pulse power facility Angara-5-1 with a discharge current level of up to 3.5 MA are presented. The outer array consisted of fibers of a substance with a low atomic number (plastic), and the inner array consisted of a substance with a high atomic number (tungsten, W). In the case of nested arrays of this design, a significant increase in the peak SXR power was obtained compared to single tungsten arrays with the same parameters as for the tungsten array in the inner array. By optimizing the linear mass of the outer array and the ratio of array radii, powerful SXR pulses were prepared with a high pulse power up to 18 TW, pulse energy of ~140 kJ and short pulse duration of ~5 ns. It is shown that by optimizing the linear mass of the outer array (fiber array) it is possible to achieve ~90% conversion of the electromagnetic energy pumped into the vicinity of the array into X-ray emission pinch energy. In this case, the fraction of the kinetic energy of the plasma implosion into the emission energy is not higher than 30%. In shots optimal over the output SXR power, an increase in the fraction of the X-ray emission energy in the spectral range of λ ∈ (30, 40) Å was recorded that is 30–100% than that in single tungsten arrays with similar parameters. [ABSTRACT FROM AUTHOR]

The results of experiments on the effect of soft X-ray radiation (SXR) on thin mylar films of micron thickness are presented. The main result of the research is the development and testing of an adaptive filter—a filter made of mylar (hereinafter, My) film with time-varying transparency. This film is necessary for profiling the multi-terawatt soft X-ray radiation pulse in the experiments on radiation ablation of the targets made of layers of some metals (e.g., Al, Ni, In, Sn, Au, Bi, etc.), currently being carried out at the Angara-5-1 facility. Such a film absorbs almost all the energy of the preliminary pulse (the so-called "pre-pulse") and becomes "transparent" by the time the main terawatt radiation pulse occurs. The distance between this film and the target under study is chosen so as not to damage the target by the spreading filter substance during its radiation heating. Thus, the target layer initial density at the time of its irradiation by the main SXR radiation pulse will increase significantly. The use of an adaptive filter makes it possible to determine the change in the target layer transparency in a wider range of the initial values of its density and to reduce the influence of the target expansion dynamics on the accuracy of measuring its spectral transparency. [ABSTRACT FROM AUTHOR]

The generation of accelerated electron beams in a high-current Z-pinch formed by the implosion of wire cylindrical tungsten arrays on an Angara-5-1 facility is studied. The most intense characteristic and bremsstrahlung X-ray radiation of fast electrons is recorded from the central region of the pinch at the pin-ching stage. The transverse size of the radiation source in the characteristic tungsten radiation Lα is ~1.5‒1.8 mm, which is close to the transverse size of the radiation source in the soft X-ray emission (1‒1.5 mm). The current of accelerated electrons generated during the implosion of the wire array and the formation of a pinch is on the order of the Alfvén current (IA). This result is consistent with the estimate of the current of accelerated electrons made from the measured characteristic radiation intensity Lα of tungsten under the assumption that the mean free path of fast electrons in a pinch is on the order of its length. [ABSTRACT FROM AUTHOR]

Abstract: Radiological methods of treatment of malignant tumors are widespread in medical practice. In addition to the type of radiation and dose and fractionation of the radiation regime, the dose rate is one of the factors that affects the effectiveness of treatment. The therapeutic dose rate lies in the range of tens of mGy/s. At modern high-current accelerators of relativistic electron beams, a significant increase in the dose rate to hundreds of MGy/s is achievable, which is more than 108 times greater than the therapeutic dose rate. It is difficult to predict the nature of processes in tissues and its cells at such radiation intensities. To determine the effect of extreme dose rate on the radiosensitivity of tissues at the Angara-5-1 facility, experiments were conducted to determine the lethal dose (LD50/30) for laboratory mice. Our result on the study of the LD50/30 dose (~100 MGy/s) allows us to make a conclusion about a possible higher lethal dose than the power range of the doses used for medical purposes. [ABSTRACT FROM AUTHOR]

A method for determining the substance density distribution in the plasma produced by a current-driven implosion of multiwire tungsten liners at the Angara-5-1 facility is described. This method is based on the X-ray probing of plasma with radiation from a point source. As a source of this radiation, an X pinch is used. The time resolution (<2 ns) was determined by the X pinch. The probing of both the liner peripheral and near-axial regions is considered. The plasma-attenuated X-pinch radiation was detected using photographic film and p–i–n diodes in the first and second approach, respectively. The spatial resolutions (over the object) in both cases were determined by the sizes of the X pinch and p–i–n diodes and amounted to 4 and 44 μm, respectively. The design of the X-pinch and the dependence of its radiation characteristics (the burst time moment and the radiation-pulse power and duration) on the electric and design parameters of the circuit and load are described. The experimental data on the X-pinch radiation spectrum in the range of photon energies of 1–20 keV and the results of studying the substance-density distribution inside liners during the current-driven implosion at the Angara-5-1 facility are presented. [ABSTRACT FROM AUTHOR]

The set of diagnostic techniques used at the Angara-5-1 facility that make it possible to study the processes which accompany the ultrafast current-driven implosion of liners is described. This set includes electric methods and methods for the detection of various radiations. The liner-plasma shapes are visualized by detecting the intrinsic liner radiation in various wavelength ranges and actively probing liners in the visible and X-ray regions. Examples of the results of studying the current-driven implosion of cylindrical arrays of tungsten wires at the Angara-5-1 facility are presented. [ABSTRACT FROM AUTHOR]